thr3ads.net - Nut upsuser - [Nut-upsuser] The dreaded Tripp Lite SMART500RT1U and NUT [Jun 2014]

If this information is useful, please help other people find it:
Share via:

Steve Ballantyne

2014-Jun-27 02:20 UTC

[Nut-upsuser] The dreaded Tripp Lite SMART500RT1U and NUT

Hello Charles,

Thanks for the feedback.  I will try to answer some of these questions:
> 09AE/0001 is essentially a USB-to-serial converter, and is not
> compatible with usbhid-ups. (Theoretically, we could have a companion
> driver that talks the same protocols over a real RS-232 port, but the
> hardware I used to develop the tripplite_usb driver only has a USB
> port.)
Ah, that makes sense.  I can see why this would simplify the
engineering and production of the unit.
> However, we don't have all of the 09AE/0001 protocols decoded in the
> tripplite_usb driver.
I can try to help out on this front?  :-)

SNIP!> >    8.154643     libusb_get_interrupt: Connection timed out
> >    8.156024     libusb_get_interrupt() returned 0 instead of 8 while
sending
> > 3a 00 ff 0d 00 00 00 00 '........'
> >    9.158554     libusb_get_interrupt: Connection timed out
> >    9.159965     libusb_get_interrupt() returned 0 instead of 8 while
sending
> > 3a 00 ff 0d 00 00 00 00 '........'SNIP!
> Hmm, this shouldn't take that long. Does it do that every time you
> start the tripplite_usb driver, or only the first time?
Only when I first start the driver.  It tries about once a second, and
then after a few failures, it connects and takes off.
> >    9.262678     send_cmd: received 00 30 05 58 58 58 58 0d
'.0.XXXX.' (OK)
> >    9.264042     send_to_all: SETINFO ups.debug.0 "30 05 58 58 58
58 0d
> > '0.XXXX.'"
> >    9.265665     send_to_all: SETINFO ups.firmware.aux "protocol
3005"
>
> Here's that 3005 protocol ID.
>
> >    9.267228     send_cmd(msg_len=3, type='W')
> >    9.267744     send_cmd: sending  3a 57 00 a8 0d 00 00 00
'.W......'
> >    9.370082     send_cmd: received 57 00 0d 00 00 00 00 00
'W.......' (OK)
>
> Your unit might support a watchdog timer.
>
> >    9.370367     send_cmd(msg_len=2, type='S')
> >    9.370565     send_cmd: sending  3a 53 ac 0d 00 00 00 00
'.S......'
> >    9.472418     send_cmd: received 53 01 04 00 00 64 00 0d
'S....d..' (OK)
That would make sense to what I am seeing.  If I leave this to run, it
will keep looping, stopping for a split second on "DATAOK".
> Ah, what we should be seeing here is that "01 04" status in
ASCII. I
> think the 3004 protocol also encodes it in binary.
>
> >    9.472712     send_to_all: SETINFO ups.mfr "Tripp Lite"
> >    9.472899     send_cmd(msg_len=2, type='P')
> >    9.473087     send_cmd: sending  3a 50 af 0d 00 00 00 00
'.P......'
> >    9.575667     send_cmd: received 50 30 30 35 30 30 58 0d
'P00500X.' (OK)
> >    9.576026     send_to_all: SETINFO ups.model
"SMART500RT1U"
> >    9.576848     send_to_all: SETINFO ups.power.nominal "500"
>
> 500W sounds right based on the name.
Yes!  It is a 500W, for sure.
> >    9.577346     send_cmd(msg_len=2, type='F')
> >    9.578194     send_cmd: sending  3a 46 b9 0d 00 00 00 00
'.F......'
> >    9.679786     send_cmd: received 46 33 33 34 34 30 31 0d
'F334401.' (OK)
> >    9.680087     send_to_all: SETINFO ups.firmware "F334401"
> >    9.680278     send_cmd(msg_len=2, type='V')
> >    9.680463     send_cmd: sending  3a 56 a9 0d 00 00 00 00
'.V......'
> >    9.782790     send_cmd: received 56 02 00 0c 01 58 58 0d
'V....XX.' (OK)
> >    9.783126     Unknown input voltage range: 0x02
> >    9.783308     Unknown number of switchable load banks: 0x01
>
> Is this a 230V unit? Again, it's looking for the ASCII version of 0x02
> (which would be 0x32)
Nope, this is a standard 120V, for a standard grounded outlet.
Although I suppose perhaps they could have shared some of the guts of
this from larger units that are 220/230v?
> >    9.783476     send_cmd(msg_len=2, type='V')
> >    9.783664     send_cmd: sending  3a 56 a9 0d 00 00 00 00
'.V......'
> >    9.885906     send_cmd: received 56 02 00 0c 01 58 58 0d
'V....XX.' (OK)
> >    9.886240     send_to_all: SETINFO ups.debug.V "02 00 0c 01 58
58 0d
> > '....XX.'"
> >    9.886425     send_cmd(msg_len=2, type='U')
> >    9.886618     send_cmd: sending  3a 55 aa 0d 00 00 00 00
'.U......'
> >    9.988651     send_cmd: received 55 00 00 0d 00 00 00 00
'U.......' (OK)
> >    9.989595     send_to_all: SETINFO ups.id "0"
> >    9.990206     send_to_all: SETFLAGS ups.id RW STRING
> >    9.990984     send_to_all: SETAUX ups.id 5
> >    9.991202     Unit ID: 0
> >    9.991406     send_to_all: SETINFO input.voltage.nominal
"120"
>
> ^ 120V might just be the default.
>
> > That last little bit between DATASTALE and DATAOK seems to loop on
through
> > infinity.  Has anyone actually made this model work with nut?  I have
dug up
> > some other very old threads that all seem to dead end without a
solution.
>
> Don't think so, but I think we can make this work with some code
> changes. Do you have access to a Windows box to verify some of the
> readings, or does it have a readout on the front?
>
> I can also get access to a Raspberry Pi if needed to rebuild the NUT
package.
I can most definitely connect this to a Windows PC.  Just let me know
what I can provide you.  For that matter, I could grant you a remote
shell to this Raspberry Pi and let you take a look.  Let me know if
that would be beneficial and I will send the connection info and
credentials directly to your gmail address.

Thanks,
Steve Ballantyne
Network Engineer
MCSE/MCDST; Novell CLA; LPIC-1; CTT+; A+; Network+; Linux+; Server+;
I-Net+; Security+; SonicWALL CSSA

Charles Lepple

2014-Jun-28 04:13 UTC

head link

[Nut-upsuser] The dreaded Tripp Lite SMART500RT1U and NUT

On Thu, Jun 26, 2014 at 10:20 PM, Steve Ballantyne
<steve.ballantyne at gmail.com> wrote:>> However, we don't have all of the 09AE/0001 protocols decoded in
the
>> tripplite_usb driver.
>
> I can try to help out on this front?  :-)
Definitely.
>> >    9.783126     Unknown input voltage range: 0x02
>> >    9.783308     Unknown number of switchable load banks: 0x01
>>
>> Is this a 230V unit? Again, it's looking for the ASCII version of
0x02
>> (which would be 0x32)
>
> Nope, this is a standard 120V, for a standard grounded outlet.
> Although I suppose perhaps they could have shared some of the guts of
> this from larger units that are 220/230v?
Well, that number scales some of the voltages. Not much we can do
until we find out more about the other values.
> I can most definitely connect this to a Windows PC.  Just let me know
> what I can provide you.
The ideal situation is a trace of all the USB commands that the
Windows software sends. However, I think this is just a binary version
of the 3003 protocol, so experimenting might be easier.

Most important are the "OB" and "LB" status bits.
Unfortunately, there
is no good way to generate the LB signal besides running the battery
down. You might need more than a Raspberry Pi to do this in short
order. I like to use incandescent lights instead of computers for test
loads, because if the UPS pulls power at an inopportune time, you
won't have nearly as much filesystem damage on a light bulb.

I think the 'M' command shows the min and max voltages - see if there
is something similar in the Windows display.

Also, any load values would be helpful.

For a 500W UPS, I assume it's one 12V (or 2x 6V) battery pack?

Attached is a patch to try to map some of the 3005 differences into
the driver. It should apply to the NUT 2.7.2 tarball, but it was
generated from the Git master branch. If you do check out from Github,
you'll need to install autoconf, automake and libtool. AsciiDoc is
pretty slow, so you can pass "--without-doc" to the ./configure
script. You may also want to add "--with-drivers=tripplite_usb" so
that it doesn't try to compile everything.

-- 
- Charles Lepple
-------------- next part --------------
A non-text attachment was scrubbed...
Name: tripplite_3005.patch
Type: text/x-patch
Size: 3847 bytes
Desc: not available
URL:
<http://lists.alioth.debian.org/pipermail/nut-upsuser/attachments/20140628/a7e23666/attachment.bin>

Steve Ballantyne

2014-Jun-29 02:05 UTC

head link

[Nut-upsuser] The dreaded Tripp Lite SMART500RT1U and NUT

Hello Charles,

I think we are making progress!  I grabbed nut using git, and applied
your patch without any problems.  Getting to the point that I could
run a configure on my RPi - was something else.  I found this blog
post, which was very helpful (for anyone else that may try it):
http://atelier-orchard.blogspot.com/2013/11/raspberry-pixf86-video-fbdev.html
 It's not in English, but you get can get the general idea of how to
move along.

Also, tripplite_usb failed to build for me with a bunch of undefined
errors.  I was able to fix it by editing the Makefile and adding -lusb
to the LD_FLAGS.

So - here I am starting up nut in debugging level 5, and it looks
"promising"?  :-)

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2014.06.28 21:54:46 =~=~=~=~=~=~=~=~=~=~=~
]0;pi at raspberrypi: ~/nut[01;32mpi at raspberrypi [01;34m~/nut
$ sudo ./drivers/tripplite_usb  -u root -a SMART500RT1U -DDDDD
Network UPS Tools - Tripp Lite OMNIVS / SMARTPRO driver 0.24
(2.7.2-signed-19-g90e2790)
Warning: This is an experimental driver.
Some features may not function correctly.

   0.000000    debug level is '5'
   0.009251    Checking device (067B/2303) (001/010)
   0.012869    - VendorID: 067b
   0.014340    - ProductID: 2303
   0.015978    - Manufacturer: Prolific Technology Inc.
   0.017231    - Product: USB-Serial Controller D
   0.018168    - Serial Number: unknown
   0.018857    - Bus: 001
   0.019029    Trying to match device
   0.019201    Device does not match - skipping
   0.020250    Checking device (09AE/0001) (001/009)
   0.023743    - VendorID: 09ae
   0.023986    - ProductID: 0001
   0.024141    - Manufacturer: TRIPP LITE
   0.024868    - Product: TRIPP LITE SMART500RT1U
   0.025049    - Serial Number: unknown
   0.025207    - Bus: 001
   0.025357    Trying to match device
   0.026318    Device matches
   0.027669    Detected a UPS: TRIPP LITE/TRIPP LITE SMART500RT1U
   0.028001    send_to_all: SETINFO ups.vendorid "09ae"
   0.028254    send_to_all: SETINFO ups.productid "0001"
   0.028468    send_to_all: SETINFO device.type "ups"
   0.029259    send_to_all: SETINFO driver.version
"2.7.2-signed-19-g90e2790"
   0.030842    send_to_all: SETINFO driver.version.internal "0.24"
   0.031065    send_to_all: SETINFO driver.name "tripplite_usb"
   0.031266    send_cmd(msg_len=2, type='
   0.031536    send_cmd: sending  3a 00 ff 0d 00 00 00 00 '........'
   1.134977    libusb_get_interrupt: Connection timed out
   1.136412    libusb_get_interrupt() returned 0 instead of 8 while
sending 3a 00 ff 0d 00 00 00 00 '........'
   2.138238    libusb_get_interrupt: Connection timed out
   2.139578    libusb_get_interrupt() returned 0 instead of 8 while
sending 3a 00 ff 0d 00 00 00 00 '........'
   3.141962    libusb_get_interrupt: Connection timed out
   3.143315    libusb_get_interrupt() returned 0 instead of 8 while
sending 3a 00 ff 0d 00 00 00 00 '........'
   4.145557    libusb_get_interrupt: Connection timed out
   4.146884    libusb_get_interrupt() returned 0 instead of 8 while
sending 3a 00 ff 0d 00 00 00 00 '........'
   5.148790    libusb_get_interrupt: Connection timed out
   5.150121    libusb_get_interrupt() returned 0 instead of 8 while
sending 3a 00 ff 0d 00 00 00 00 '........'
   6.152078    libusb_get_interrupt: Connection timed out
   6.153425    libusb_get_interrupt() returned 0 instead of 8 while
sending 3a 00 ff 0d 00 00 00 00 '........'
   7.155406    libusb_get_interrupt: Connection timed out
   7.156855    libusb_get_interrupt() returned 0 instead of 8 while
sending 3a 00 ff 0d 00 00 00 00 '........'
   8.158953    libusb_get_interrupt: Connection timed out
   8.160283    libusb_get_interrupt() returned 0 instead of 8 while
sending 3a 00 ff 0d 00 00 00 00 '........'
   9.162442    libusb_get_interrupt: Connection timed out
   9.163820    libusb_get_interrupt() returned 0 instead of 8 while
sending 3a 00 ff 0d 00 00 00 00 '........'
   9.266486    send_cmd: received 00 30 05 58 58 58 58 0d '.0.XXXX.'
(OK)
   9.267788    Using binary SMART protocol (3005)
   9.269255    send_to_all: SETINFO ups.firmware.aux "protocol 3005"
   9.270696    send_cmd(msg_len=3, type='W')
   9.271796    send_cmd: sending  3a 57 00 a8 0d 00 00 00 '.W......'
   9.373487    send_cmd: received 57 00 0d 00 00 00 00 00 'W.......'
(OK)
   9.373744    send_cmd(msg_len=2, type='S')
   9.374505    send_cmd: sending  3a 53 ac 0d 00 00 00 00 '.S......'
   9.476233    send_cmd: received 53 01 04 00 00 64 00 0d 'S....d..'
(OK)
   9.476533    send_to_all: SETINFO ups.mfr "Tripp Lite"
   9.476718    send_cmd(msg_len=2, type='P')
   9.477542    send_cmd: sending  3a 50 af 0d 00 00 00 00 '.P......'
   9.579226    send_cmd: received 50 30 30 35 30 30 58 0d 'P00500X.'
(OK)
   9.579630    send_to_all: SETINFO ups.model "SMART500RT1U"
   9.580498    send_to_all: SETINFO ups.power.nominal "500"
   9.580690    send_cmd(msg_len=2, type='F')
   9.580881    send_cmd: sending  3a 46 b9 0d 00 00 00 00 '.F......'
   9.682969    send_cmd: received 46 33 33 34 34 30 31 0d 'F334401.'
(OK)
   9.683895    send_to_all: SETINFO ups.firmware "F334401"
   9.684100    send_cmd(msg_len=2, type='V')
   9.684297    send_cmd: sending  3a 56 a9 0d 00 00 00 00 '.V......'
   9.786346    send_cmd: received 56 02 00 0c 01 58 58 0d 'V....XX.'
(OK)
   9.786612    Unknown number of switchable load banks: 0x01
   9.786779    Switchable load banks: 1
   9.786948    send_cmd(msg_len=2, type='V')
   9.787138    send_cmd: sending  3a 56 a9 0d 00 00 00 00 '.V......'
   9.889087    send_cmd: received 56 02 00 0c 01 58 58 0d 'V....XX.'
(OK)
   9.889423    send_to_all: SETINFO ups.debug.V "02 00 0c 01 58 58 0d
'....XX.'"
   9.889634    send_to_all: SETINFO outlet.1.id "1"
   9.890441    send_to_all: SETINFO outlet.1.desc "Load 1"
   9.890702    send_to_all: SETINFO outlet.1.switchable "1"
   9.890907    send_to_all: SETINFO outlet.1.switch "1"
   9.891096    send_to_all: SETFLAGS outlet.1.switch RW STRING
   9.892121    send_to_all: SETAUX outlet.1.switch 3
   9.892951    send_to_all: SETINFO outlet.2.id "2"
   9.893179    send_to_all: SETINFO outlet.2.desc "Load 2"
   9.894177    send_to_all: SETINFO outlet.2.switchable "0"
   9.894970    send_to_all: ADDCMD load.on
   9.895171    send_to_all: ADDCMD load.off
   9.895337    send_cmd(msg_len=2, type='U')
   9.895731    send_cmd: sending  3a 55 aa 0d 00 00 00 00 '.U......'
   9.997588    send_cmd: received 55 00 00 0d 00 00 00 00 'U.......'
(OK)
   9.998444    send_to_all: SETINFO ups.id "0"
   9.999497    send_to_all: SETFLAGS ups.id RW STRING
   9.999749    send_to_all: SETAUX ups.id 5
   9.999919    Unit ID: 0
  10.000672    send_to_all: SETINFO input.voltage.nominal "120"
  10.000895    send_to_all: SETINFO battery.voltage.nominal "12"
  10.001097    send_to_all: SETINFO ups.debug.load_banks "1"
  10.002045    send_to_all: SETINFO ups.delay.shutdown "64"
  10.002259    send_to_all: SETFLAGS ups.delay.shutdown RW STRING
  10.002448    send_to_all: SETAUX ups.delay.shutdown 3
  10.002633    send_to_all: ADDCMD shutdown.return
Attached to Tripp Lite SMART500RT1U
  10.003768    send_cmd(msg_len=2, type='S')
  10.004587    send_cmd: sending  3a 53 ac 0d 00 00 00 00 '.S......'
  10.106335    send_cmd: received 53 01 04 00 00 64 00 0d 'S....d..'
(OK)
  10.106677    send_to_all: SETINFO ups.debug.S "01 04 00 00 64 00 0d
'....d..'"
  10.107513    send_to_all: SETINFO ups.status "OL"
  10.107814    send_cmd(msg_len=2, type='L')
  10.108823    send_cmd: sending  3a 4c b3 0d 00 00 00 00 '.L......'
  10.211079    send_cmd: received 4c 00 00 00 07 58 58 0d 'L....XX.'
(OK)
  10.211427    send_to_all: SETINFO ups.debug.L "00 00 00 07 58 58 0d
'....XX.'"
  10.211709    send_cmd(msg_len=2, type='D')
  10.212540    send_cmd: sending  3a 44 bb 0d 00 00 00 00 '.D......'
  10.314200    send_cmd: received 44 00 7b 00 8b 0d 00 00 'D.......'
(OK)
  10.314545    send_to_all: SETINFO ups.debug.D "00 7b 00 8b 0d 00 00
'.......'"
  10.314742    send_cmd(msg_len=2, type='V')
  10.315785    send_cmd: sending  3a 56 a9 0d 00 00 00 00 '.V......'
  10.417567    send_cmd: received 56 02 00 0c 01 58 58 0d 'V....XX.'
(OK)
  10.417872    send_cmd(msg_len=2, type='M')
  10.418080    send_cmd: sending  3a 4d b2 0d 00 00 00 00 '.M......'
  10.520316    send_cmd: received 4d 00 75 00 7f 0d 00 00 'M.u.....'
(OK)
  10.520657    send_to_all: SETINFO ups.debug.M "00 75 00 7f 0d 00 00
'.u.....'"
  10.520853    send_cmd(msg_len=2, type='T')
  10.521641    send_cmd: sending  3a 54 ab 0d 00 00 00 00 '.T......'
  10.623318    send_cmd: received 54 21 00 02 58 01 58 0d 'T...X.X.'
(OK)
  10.623659    send_to_all: SETINFO ups.debug.T "21 00 02 58 01 58 0d
'...X.X.'"
  10.623852    send_cmd(msg_len=2, type='P')
  10.624634    send_cmd: sending  3a 50 af 0d 00 00 00 00 '.P......'
  10.726438    send_cmd: received 50 30 30 35 30 30 58 0d 'P00500X.'
(OK)
  10.726781    send_to_all: SETINFO ups.debug.P "30 30 35 30 30 58 0d
'00500X.'"
  10.726971    send_to_all: DATAOK
  10.727871    dstate_init: sock
/var/state/ups/tripplite_usb-SMART500RT1U open on fd 5
  10.729279    send_to_all: SETINFO driver.parameter.pollinterval "2"
  10.730340    send_to_all: SETINFO device.mfr "Tripp Lite"
  10.730565    send_to_all: SETINFO device.model "SMART500RT1U"
  10.730760    send_cmd(msg_len=2, type='S')
  10.731809    send_cmd: sending  3a 53 ac 0d 00 00 00 00 '.S......'
  10.834055    send_cmd: received 53 01 04 00 00 64 00 0d 'S....d..'
(OK)
  10.834373    send_cmd(msg_len=2, type='L')
  10.834584    send_cmd: sending  3a 4c b3 0d 00 00 00 00 '.L......'
  10.937047    send_cmd: received 4c 00 00 00 07 58 58 0d 'L....XX.'
(OK)
  10.937362    send_cmd(msg_len=2, type='D')
  10.937572    send_cmd: sending  3a 44 bb 0d 00 00 00 00 '.D......'
  11.039299    send_cmd: received 44 00 7b 00 8b 0d 00 00 'D.......'
(OK)
  11.039609    send_cmd(msg_len=2, type='V')
  11.039819    send_cmd: sending  3a 56 a9 0d 00 00 00 00 '.V......'
  11.141543    send_cmd: received 56 02 00 0c 01 58 58 0d 'V....XX.'
(OK)
  11.141856    send_cmd(msg_len=2, type='M')
  11.142633    send_cmd: sending  3a 4d b2 0d 00 00 00 00 '.M......'
  11.244423    send_cmd: received 4d 00 75 00 7f 0d 00 00 'M.u.....'
(OK)
  11.244740    send_cmd(msg_len=2, type='T')
  11.244945    send_cmd: sending  3a 54 ab 0d 00 00 00 00 '.T......'
  11.346902    send_cmd: received 54 21 00 02 58 01 58 0d 'T...X.X.'
(OK)
  11.347209    send_cmd(msg_len=2, type='P')
  11.347416    send_cmd: sending  3a 50 af 0d 00 00 00 00 '.P......'
  11.450029    send_cmd: received 50 30 30 35 30 30 58 0d 'P00500X.'
(OK)
  12.732166    send_cmd(msg_len=2, type='S')
  12.732472    send_cmd: sending  3a 53 ac 0d 00 00 00 00 '.S......'
  13.498966    send_cmd: received 53 01 04 00 00 64 00 0d 'S....d..'
(OK)
  13.500378    send_cmd(msg_len=2, type='L')
  13.501956    send_cmd: sending  3a 4c b3 0d 00 00 00 00 '.L......'
  13.604452    send_cmd: received 4c 00 00 00 07 58 58 0d 'L....XX.'
(OK)
  13.605955    send_cmd(msg_len=2, type='D')
  13.607466    send_cmd: sending  3a 44 bb 0d 00 00 00 00 '.D......'
  13.709952    send_cmd: received 44 00 7c 00 8b 0d 00 00 'D.......'
(OK)
  13.710289    send_to_all: SETINFO ups.debug.D "00 7c 00 8b 0d 00 00
'.......'"
  13.710488    send_cmd(msg_len=2, type='V')
  13.711316    send_cmd: sending  3a 56 a9 0d 00 00 00 00 '.V......'
  13.812948    send_cmd: received 56 02 00 0c 01 58 58 0d 'V....XX.'
(OK)
  13.813265    send_cmd(msg_len=2, type='M')
  13.813469    send_cmd: sending  3a 4d b2 0d 00 00 00 00 '.M......'
  13.915820    send_cmd: received 4d 00 75 00 7f 0d 00 00 'M.u.....'
(OK)
  13.916146    send_cmd(msg_len=2, type='T')
  13.916351    send_cmd: sending  3a 54 ab 0d 00 00 00 00 '.T......'
  14.018069    send_cmd: received 54 21 00 02 58 01 58 0d 'T...X.X.'
(OK)
  14.018384    send_cmd(msg_len=2, type='P')
  14.018590    send_cmd: sending  3a 50 af 0d 00 00 00 00 '.P......'
  14.121062    send_cmd: received 50 30 30 35 30 30 58 0d 'P00500X.'
(OK)
  14.733109    send_cmd(msg_len=2, type='S')
  14.735078    send_cmd: sending  3a 53 ac 0d 00 00 00 00 '.S......'
  14.837041    send_cmd: received 53 01 04 00 00 64 00 0d 'S....d..'
(OK)
  14.837368    send_cmd(msg_len=2, type='L')
  14.837575    send_cmd: sending  3a 4c b3 0d 00 00 00 00 '.L......'
  14.939282    send_cmd: received 4c 00 00 00 07 58 58 0d 'L....XX.'
(OK)
  14.939678    send_cmd(msg_len=2, type='D')
  14.940503    send_cmd: sending  3a 44 bb 0d 00 00 00 00 '.D......'
  15.042159    send_cmd: received 44 00 7b 00 8b 0d 00 00 'D.......'
(OK)
  15.042502    send_to_all: SETINFO ups.debug.D "00 7b 00 8b 0d 00 00
'.......'"
  15.043276    send_cmd(msg_len=2, type='V')
  15.043631    send_cmd: sending  3a 56 a9 0d 00 00 00 00 '.V......'
  15.145271    send_cmd: received 56 02 00 0c 01 58 58 0d 'V....XX.'
(OK)
  15.145657    send_cmd(msg_len=2, type='M')
  15.146481    send_cmd: sending  3a 4d b2 0d 00 00 00 00 '.M......'
  15.248151    send_cmd: received 4d 00 75 00 7f 0d 00 00 'M.u.....'
(OK)
  15.248466    send_cmd(msg_len=2, type='T')
  15.248680    send_cmd: sending  3a 54 ab 0d 00 00 00 00 '.T......'
  15.350894    send_cmd: received 54 21 00 02 58 01 58 0d 'T...X.X.'
(OK)
  15.351210    send_cmd(msg_len=2, type='P')
  15.351418    send_cmd: sending  3a 50 af 0d 00 00 00 00 '.P......'
  15.453137    send_cmd: received 50 30 30 35 30 30 58 0d 'P00500X.'
(OK)
  16.734021    send_cmd(msg_len=2, type='S')
  16.734325    send_cmd: sending  3a 53 ac 0d 00 00 00 00 '.S......'
  17.501817    send_cmd: received 53 01 04 00 00 64 00 0d 'S....d..'
(OK)
  17.503193    send_cmd(msg_len=2, type='L')
  17.505396    send_cmd: sending  3a 4c b3 0d 00 00 00 00 '.L......'
  17.607935    send_cmd: received 4c 00 00 00 07 58 58 0d 'L....XX.'
(OK)
  17.609518    send_cmd(msg_len=2, type='D')
  17.610533    send_cmd: sending  3a 44 bb 0d 00 00 00 00 '.D......'
  17.712807    send_cmd: received 44 00 7c 00 8b 0d 00 00 'D.......'
(OK)
  17.713145    send_to_all: SETINFO ups.debug.D "00 7c 00 8b 0d 00 00
'.......'"
  17.713950    send_cmd(msg_len=2, type='V')
  17.714182    send_cmd: sending  3a 56 a9 0d 00 00 00 00 '.V......'
  17.815823    send_cmd: received 56 02 00 0c 01 58 58 0d 'V....XX.'
(OK)
  17.816145    send_cmd(msg_len=2, type='M')
  17.816957    send_cmd: sending  3a 4d b2 0d 00 00 00 00 '.M......'
  17.918798    send_cmd: received 4d 00 75 00 7f 0d 00 00 'M.u.....'
(OK)
  17.919115    send_cmd(msg_len=2, type='T')
  17.919319    send_cmd: sending  3a 54 ab 0d 00 00 00 00 '.T......'
  18.021673    send_cmd: received 54 21 00 02 58 01 58 0d 'T...X.X.'
(OK)
  18.021992    send_cmd(msg_len=2, type='P')
  18.022200    send_cmd: sending  3a 50 af 0d 00 00 00 00 '.P......'
  18.123915    send_cmd: received 50 30 30 35 30 30 58 0d 'P00500X.'
(OK)
  18.734697    send_cmd(msg_len=2, type='S')
  18.734994    send_cmd: sending  3a 53 ac 0d 00 00 00 00 '.S......'
  18.836767    send_cmd: received 53 01 04 00 00 64 00 0d 'S....d..'
(OK)
  18.837096    send_cmd(msg_len=2, type='L')
  18.837302    send_cmd: sending  3a 4c b3 0d 00 00 00 00 '.L......'
  18.939418    send_cmd: received 4c 00 00 00 07 58 58 0d 'L....XX.'
(OK)
  18.940313    send_cmd(msg_len=2, type='D')
  18.940544    send_cmd: sending  3a 44 bb 0d 00 00 00 00 '.D......'
  19.042634    send_cmd: received 44 00 7c 00 8b 0d 00 00 'D.......'
(OK)
  19.043585    send_cmd(msg_len=2, type='V')
  19.043805    send_cmd: sending  3a 56 a9 0d 00 00 00 00 '.V......'
  19.145770    send_cmd: received 56 02 00 0c 01 58 58 0d 'V....XX.'
(OK)
  19.146653    send_cmd(msg_len=2, type='M')
  19.146883    send_cmd: sending  3a 4d b2 0d 00 00 00 00 '.M......'
  19.248878    send_cmd: received 4d 00 75 00 7f 0d 00 00 'M.u.....'
(OK)
  19.249767    send_cmd(msg_len=2, type='T')
  19.249991    send_cmd: sending  3a 54 ab 0d 00 00 00 00 '.T......'
  19.351995    send_cmd: received 54 21 00 02 58 01 58 0d 'T...X.X.'
(OK)
  19.352888    send_cmd(msg_len=2, type='P')
  19.353119    send_cmd: sending  3a 50 af 0d 00 00 00 00 '.P......'
  19.455629    send_cmd: received 50 30 30 35 30 30 58 0d 'P00500X.'
(OK)
  20.736059    send_cmd(msg_len=2, type='S')
  20.736356    send_cmd: sending  3a 53 ac 0d 00 00 00 00 '.S......'
  21.504675    send_cmd: received 53 01 04 00 00 64 00 0d 'S....d..'
(OK)
  21.506853    send_cmd(msg_len=2, type='L')
  21.508402    send_cmd: sending  3a 4c b3 0d 00 00 00 00 '.L......'
  21.611195    send_cmd: received 4c 00 00 00 07 58 58 0d 'L....XX.'
(OK)
  21.612791    send_cmd(msg_len=2, type='D')
  21.613067    send_cmd: sending  3a 44 bb 0d 00 00 00 00 '.D......'
  21.714789    send_cmd: received 44 00 7b 00 8b 0d 00 00 'D.......'
(OK)
  21.715168    send_to_all: SETINFO ups.debug.D "00 7b 00 8b 0d 00 00
'.......'"
  21.716130    send_cmd(msg_len=2, type='V')
  21.716358    send_cmd: sending  3a 56 a9 0d 00 00 00 00 '.V......'
  21.818034    send_cmd: received 56 02 00 0c 01 58 58 0d 'V....XX.'
(OK)
  21.818349    send_cmd(msg_len=2, type='M')
  21.818557    send_cmd: sending  3a 4d b2 0d 00 00 00 00 '.M......'
  21.920908    send_cmd: received 4d 00 75 00 7f 0d 00 00 'M.u.....'
(OK)
  21.921229    send_cmd(msg_len=2, type='T')
  21.921431    send_cmd: sending  3a 54 ab 0d 00 00 00 00 '.T......'
  22.023152    send_cmd: received 54 21 00 02 58 01 58 0d 'T...X.X.'
(OK)
  22.023465    send_cmd(msg_len=2, type='P')
  22.024245    send_cmd: sending  3a 50 af 0d 00 00 00 00 '.P......'
  22.126141    send_cmd: received 50 30 30 35 30 30 58 0d 'P00500X.'
(OK)
  22.736742    send_cmd(msg_len=2, type='S')
  22.737034    send_cmd: sending  3a 53 ac 0d 00 00 00 00 '.S......'
  22.838748    send_cmd: received 53 01 04 00 00 64 00 0d 'S....d..'
(OK)
  22.839115    send_cmd(msg_len=2, type='L')
  22.839382    send_cmd: sending  3a 4c b3 0d 00 00 00 00 '.L......'
  22.941110    send_cmd: received 4c 00 00 00 07 58 58 0d 'L....XX.'
(OK)
  22.941432    send_cmd(msg_len=2, type='D')
  22.941643    send_cmd: sending  3a 44 bb 0d 00 00 00 00 '.D......'
  23.043611    send_cmd: received 44 00 7c 00 8b 0d 00 00 'D.......'
(OK)
  23.044771    send_to_all: SETINFO ups.debug.D "00 7c 00 8b 0d 00 00
'.......'"
  23.045669    send_cmd(msg_len=2, type='V')
  23.045908    send_cmd: sending  3a 56 a9 0d 00 00 00 00 '.V......'
  23.148484    send_cmd: received 56 02 00 0c 01 58 58 0d 'V....XX.'
(OK)
  23.148795    send_cmd(msg_len=2, type='M')
  23.149004    send_cmd: sending  3a 4d b2 0d 00 00 00 00 '.M......'
  23.250732    send_cmd: received 4d 00 75 00 7f 0d 00 00 'M.u.....'
(OK)
  23.251046    send_cmd(msg_len=2, type='T')
  23.251353    send_cmd: sending  3a 54 ab 0d 00 00 00 00 '.T......'
  23.353102    send_cmd: received 54 21 00 02 58 01 58 0d 'T...X.X.'
(OK)
  23.353413    send_cmd(msg_len=2, type='P')
  23.354181    send_cmd: sending  3a 50 af 0d 00 00 00 00 '.P......'
  23.456221    send_cmd: received 50 30 30 35 30 30 58 0d 'P00500X.'
(OK)

  24.738110    send_cmd(msg_len=2, type='S')
  24.738414    send_cmd: sending  3a 53 ac 0d 00 00 00 00 '.S......'

M  25.504530    send_cmd: received 53 01 04 00 00 64 00 0d 'S....d..'
(OK)
  25.506212    send_cmd(msg_len=2, type='L')
  25.507751    send_cmd: sending  3a 4c b3 0d 00 00 00 00 '.L......'
  25.610516    send_cmd: received 4c 00 00 00 07 58 58 0d 'L....XX.'
(OK)
  25.612137    send_cmd(msg_len=2, type='D')
  25.612415    send_cmd: sending  3a 44 bb 0d 00 00 00 00 '.D......'
  25.714768    send_cmd: received 44 00 7b 00 8b 0d 00 00 'D.......'
(OK)
  25.715196    send_to_all: SETINFO ups.debug.D "00 7b 00 8b 0d 00 00
'.......'"
  25.715411    send_cmd(msg_len=2, type='V')
  25.716276    send_cmd: sending  3a 56 a9 0d 00 00 00 00 '.V......'
  25.818389    send_cmd: received 56 02 00 0c 01 58 58 0d 'V....XX.'
(OK)
  25.818702    send_cmd(msg_len=2, type='M')
  25.818911    send_cmd: sending  3a 4d b2 0d 00 00 00 00 '.M......'
  25.921012    send_cmd: received 4d 00 75 00 7f 0d 00 00 'M.u.....'
(OK)
  25.921908    send_cmd(msg_len=2, type='T')
  25.922133    send_cmd: sending  3a 54 ab 0d 00 00 00 00 '.T......'

  26.024131    send_cmd: received 54 21 00 02 58 01 58 0d 'T...X.X.'
(OK)
  26.024440    send_cmd(msg_len=2, type='P')
  26.024644    send_cmd: sending  3a 50 af 0d 00 00 00 00 '.P......'
  26.126499    send_cmd: received 50 30 30 35 30 30 58 0d 'P00500X.'
(OK)
  26.738798    send_cmd(msg_len=2, type='S')
  26.739205    send_cmd: sending  3a 53 ac 0d 00 00 00 00 '.S......'
  26.840964    send_cmd: received 53 01 04 00 00 64 00 0d 'S....d..'
(OK)
  26.841278    send_cmd(msg_len=2, type='L')
  26.841482    send_cmd: sending  3a 4c b3 0d 00 00 00 00 '.L......'
  26.943342    send_cmd: received 4c 00 00 00 07 58 58 0d 'L....XX.'
(OK)
  26.943664    send_cmd(msg_len=2, type='D')
  26.943878    send_cmd: sending  3a 44 bb 0d 00 00 00 00 '.D......'
  27.045860    send_cmd: received 44 00 7b 00 8b 0d 00 00 'D.......'
(OK)
  27.046746    send_cmd(msg_len=2, type='V')
  27.047811    send_cmd: sending  3a 56 a9 0d 00 00 00 00 '.V......'
  27.149468    send_cmd: received 56 02 00 0c 01 58 58 0d 'V....XX.'
(OK)
  27.149778    send_cmd(msg_len=2, type='M')
  27.150550    send_cmd: sending  3a 4d b2 0d 00 00 00 00 '.M......'
  27.252339    send_cmd: received 4d 00 75 00 7f 0d 00 00 'M.u.....'
(OK)
  27.252654    send_cmd(msg_len=2, type='T')
  27.252863    send_cmd: sending  3a 54 ab 0d 00 00 00 00 '.T......'
  27.355117    send_cmd: received 54 21 00 02 58 01 58 0d 'T...X.X.'
(OK)
  27.355441    send_cmd(msg_len=2, type='P')
  27.355804    send_cmd: sending  3a 50 af 0d 00 00 00 00 '.P......'
  27.457570    send_cmd: received 50 30 30 35 30 30 58 0d 'P00500X.'
(OK)
  28.740148    send_cmd(msg_len=2, type='S')
  28.740435    send_cmd: sending  3a 53 ac 0d 00 00 00 00 '.S......'
  29.506383    send_cmd: received 53 01 04 00 00 64 00 0d 'S....d..'
(OK)
  29.507771    send_cmd(msg_len=2, type='L')
  29.509988    send_cmd: sending  3a 4c b3 0d 00 00 00 00 '.L......'
  29.612497    send_cmd: received 4c 00 00 00 07 58 58 0d 'L....XX.'
(OK)
  29.613828    send_cmd(msg_len=2, type='D')
  29.615070    send_cmd: sending  3a 44 bb 0d 00 00 00 00 '.D......'
  29.717374    send_cmd: received 44 00 7c 00 8b 0d 00 00 'D.......'
(OK)
  29.717720    send_to_all: SETINFO ups.debug.D "00 7c 00 8b 0d 00 00
'.......'"
  29.717915    send_cmd(msg_len=2, type='V')
  29.718114    send_cmd: sending  3a 56 a9 0d 00 00 00 00 '.V......'
  29.820365    send_cmd: received 56 02 00 0c 01 58 58 0d 'V....XX.'
(OK)
  29.820680    send_cmd(msg_len=2, type='M')
  29.820889    send_cmd: sending  3a 4d b2 0d 00 00 00 00 '.M......'
  29.922615    send_cmd: received 4d 00 75 00 7f 0d 00 00 'M.u.....'
(OK)
  29.923014    send_cmd(msg_len=2, type='T')
  29.923229    send_cmd: sending  3a 54 ab 0d 00 00 00 00 '.T......'
  30.025616    send_cmd: received 54 21 00 02 58 01 58 0d 'T...X.X.'
(OK)
  30.025918    send_cmd(msg_len=2, type='P')
  30.026125    send_cmd: sending  3a 50 af 0d 00 00 00 00 '.P......'
  30.128359    send_cmd: received 50 30 30 35 30 30 58 0d 'P00500X.'
(OK)
  30.740839    send_cmd(msg_len=2, type='S')
  30.741135    send_cmd: sending  3a 53 ac 0d 00 00 00 00 '.S......'
  30.842861    send_cmd: received 53 01 04 00 00 64 00 0d 'S....d..'
(OK)
  30.843227    send_cmd(msg_len=2, type='L')
  30.843435    send_cmd: sending  3a 4c b3 0d 00 00 00 00 '.L......'
  30.945447    send_cmd: received 4c 00 00 00 07 58 58 0d 'L....XX.'
(OK)
  30.946484    send_cmd(msg_len=2, type='D')
  30.946717    send_cmd: sending  3a 44 bb 0d 00 00 00 00 '.D......'
  31.048828    send_cmd: received 44 00 7b 00 8b 0d 00 00 'D.......'
(OK)
  31.049747    send_to_all: SETINFO ups.debug.D "00 7b 00 8b 0d 00 00
'.......'"
  31.050467    send_cmd(msg_len=2, type='V')
  31.050737    send_cmd: sending  3a 56 a9 0d 00 00 00 00 '.V......'
  31.152695    send_cmd: received 56 02 00 0c 01 58 58 0d 'V....XX.'
(OK)
  31.153004    send_cmd(msg_len=2, type='M')
  31.153213    send_cmd: sending  3a 4d b2 0d 00 00 00 00 '.M......'
  31.255700    send_cmd: received 4d 00 75 00 7f 0d 00 00 'M.u.....'
(OK)
  31.256017    send_cmd(msg_len=2, type='T')
  31.256214    send_cmd: sending  3a 54 ab 0d 00 00 00 00 '.T......'
  31.357942    send_cmd: received 54 21 00 02 58 01 58 0d 'T...X.X.'
(OK)
  31.358258    send_cmd(msg_len=2, type='P')
  31.358466    send_cmd: sending  3a 50 af 0d 00 00 00 00 '.P......'
  31.460306    send_cmd: received 50 30 30 35 30 30 58 0d 'P00500X.'
(OK)
  32.742203    send_cmd(msg_len=2, type='S')
  32.742512    send_cmd: sending  3a 53 ac 0d 00 00 00 00 '.S......'
  33.509240    send_cmd: received 53 01 04 00 00 64 00 0d 'S....d..'
(OK)
  33.510607    send_cmd(msg_len=2, type='L')
  33.512818    send_cmd: sending  3a 4c b3 0d 00 00 00 00 '.L......'
  33.615361    send_cmd: received 4c 00 00 00 07 58 58 0d 'L....XX.'
(OK)
  33.617516    send_cmd(msg_len=2, type='D')
  33.617785    send_cmd: sending  3a 44 bb 0d 00 00 00 00 '.D......'
  33.719724    send_cmd: received 44 00 7c 00 8b 0d 00 00 'D.......'
(OK)
  33.720061    send_to_all: SETINFO ups.debug.D "00 7c 00 8b 0d 00 00
'.......'"
  33.720256    send_cmd(msg_len=2, type='V')
  33.721037    send_cmd: sending  3a 56 a9 0d 00 00 00 00 '.V......'
  33.823099    send_cmd: received 56 02 00 0c 01 58 58 0d 'V....XX.'
(OK)
  33.823415    send_cmd(msg_len=2, type='M')
  33.823621    send_cmd: sending  3a 4d b2 0d 00 00 00 00 '.M......'
^C]0;pi at raspberrypi: ~/nut[01;32mpi at raspberrypi [01;34m~/nut $

Steve Ballantyne
Network Engineer
MCSE/MCDST; Novell CLA; LPIC-1; CTT+; A+; Network+; Linux+; Server+;
I-Net+; Security+; SonicWALL CSSA


On Sat, Jun 28, 2014 at 12:13 AM, Charles Lepple <clepple at gmail.com>
wrote:
> Attached is a patch to try to map some of the 3005 differences into
> the driver. It should apply to the NUT 2.7.2 tarball, but it was
> generated from the Git master branch. If you do check out from Github,
> you'll need to install autoconf, automake and libtool. AsciiDoc is
> pretty slow, so you can pass "--without-doc" to the ./configure
> script. You may also want to add "--with-drivers=tripplite_usb"
so
> that it doesn't try to compile everything.

Steve Ballantyne

2014-Jul-01 13:17 UTC

head link

[Nut-upsuser] The dreaded Tripp Lite SMART500RT1U and NUT

Hello Charles,

Thank you for all of your help this far.  I have made some great
progress.  I was hung up with all sorts of USB problems which we can
chalk up to a "blonde moment" for me (or more accurately, a *bald*
moment).  In all my starting over and screwing around, I had forgotten
to reinstall libusb-compat.  Duh!  I am now to a point that I think we
can dig a little deeper.

The patch that you provided me works fine, and allows a connection
with some basic values (see bottom of thread).

On Sat, Jun 28, 2014 at 12:13 AM, Charles Lepple <clepple at gmail.com>
wrote:> The ideal situation is a trace of all the USB commands that the
> Windows software sends. However, I think this is just a binary version
> of the 3003 protocol, so experimenting might be easier.
SNIP, SNIP> I think the 'M' command shows the min and max voltages - see if
there
> is something similar in the Windows display.
How would I go about providing you this stuff?  Can you point me to
something that would help trace out the USB data?  I can install the
software, and run it, but I would need some guidance on grabbing the
USB debug info.  This UPS has produces some really helpful data if we
can manage to yank it out of there.  Examples, charge remaining (in
percentage), temperature, age of the battery, date of last self test,
etc.
> Attached is a patch to try to map some of the 3005 differences into
> the driver. It should apply to the NUT 2.7.2 tarball, but it was
> generated from the Git master branch. If you do check out from Github,
> you'll need to install autoconf, automake and libtool. AsciiDoc is
> pretty slow, so you can pass "--without-doc" to the ./configure
> script. You may also want to add "--with-drivers=tripplite_usb"
so
> that it doesn't try to compile everything.
Your patch, along with a lot of other Raspbian/Debian changes got me
up and running.  For any other fool that would dare attempt this ... I
am providing what it took to get this up and running.  Note that there
are some direct links in here to mirrors that could go belly up.  And
I may not be choosing the most ideal of permissions.  While you might
be able to copy and paste this into a shell script and run it ... I
would suggest stepping using these steps only as guidance.

### BEGIN SCRIPT ###

#some depencies from repo
sudo apt-get -y install m4 libtool libudev-dev automake

#fixing autoconf for later
sudo ln -s /usr/share/autoconf/Autom4te /usr/local/share/autoreconf/Autom4te
sudo ln -s /usr/bin/autom4te /usr/local/bin/autom4te
sudo ln -s /usr/bin/autoconf /usr/local/bin/autoconf
sudo ln -s /usr/bin/autoheader /usr/local/bin/autoheader

#installing nut dependencies
mkdir nut-depends
cd ./nut-depends

# acscripts from source
wget
http://sourceforge.net/projects/acscripts.berlios/files/acscripts-0.0.1.13.tar.bz2
tar xf acscripts-0.0.1.13.tar.bz2
sudo mkdir /usr/lib/scripts
sudo mv acscripts-0.0.1.13 /usr/lib/scripts/acscripts

#autoreconf from source
wget
http://sourceforge.net/projects/autoreconf/files/0.0.0.1/autoreconf-0.0.0.1.tar.bz2
tar xf autoreconf-0.0.0.1.tar.bz2
cd autoreconf-0.0.0.1
./configure && sudo make install
cd ..

#libusb and libusb-compat from source
wget
"http://downloads.sourceforge.net/project/libusb/libusb-1.0/libusb-1.0.18/libusb-1.0.18.tar.bz2?r=http%3A%2F%2Fwww.libusb.org%2F&ts=1404210716&use_mirror=softlayer-ams"
-O libusb-1.0.18.tar.bz2
tar -xjf libusb-1.0.18.tar.bz2
cd libusb-1.0.18
./configure && sudo make install
cd ..
wget
"http://downloads.sourceforge.net/project/libusb/libusb-compat-0.1/libusb-compat-0.1.4/libusb-compat-0.1.4.tar.bz2?r=http%3A%2F%2Fwww.libusb.org%2F&ts=1404210428&use_mirror=softlayer-ams"
-O libusb-compat-0.1.4.tar.bz2
tar -xjf libusb-compat-0.1.4.tar.bz2
cd libusb-compat-0.1.4
./configure && sudo make install
cd ..

#get back to home root
cd ..

#download nut from dev repo
git clone git://github.com/networkupstools/nut.git
cd nut

#patch for TrippLite SMART500RT1U
wget
http://lists.alioth.debian.org/pipermail/nut-upsuser/attachments/20140628/a7e23666/attachment.bin
-O charles-tripplite.patch
patch -p1 < charles-tripplite.patch

echo "Running autogen ..."
./autogen.sh

#create some groups and directories and mod some persmissions
sudo groupadd nut
sudo usermod -a -G nut pi
sudo usermod -a -G nut root
sudo mkdir /var/run/nut
sudo chown root:nut /var/run/nut
sudo mkdir -p /var/state/ups
sudo chown root:nut /var/state/ups
sudo chmod 0770 /var/state/ups

#now we ./configure and make it
./configure --without-doc --with-drivers=tripplite_usb,upsdrvctl

#still tries to build docs, even though I said NO to docs
cp Makefile Makefile.orig
sed -i 's/include common clients conf data tools docs drivers/include
common clients conf data tools drivers/' Makefile

make
sudo make install

### END SCRIPT ###

### BEGIN CONFIG FILE CHANGES / STARTUP ###

sudo vi /usr/local/ups/etc/ups.conf

[SMART500RT1U]
        driver = tripplite_usb
        port = auto
        desc = "Tripp Lite SmartUPS 500RT 1U"

sudo vi /etc/udev/rules.d/90-nut-ups.rules

# TrippLite UPS [09ae:0001]
ACTION=="add", \
SUBSYSTEM=="usb", \
ATTR{idVendor}=="09ae", ATTR{idProduct}=="0001", \
MODE="0666", GROUP="nut"

sudo vi /usr/local/ups/etc/upsd.users

[pi]
        password = pi
        upsmon master
MONITOR SMART500RT1U at localhost 1 pi pass master

sudo vi /usr/local/ups/etc/upsd.conf # DEFAULTS
# LISTEN ::1 3493
# LISTEN localhost 3493

sudo chown root:nut /usr/local/ups/etc/upsd.conf /usr/local/ups/etc/upsd.users
sudo chmod 0640 /usr/local/ups/etc/upsd.conf /usr/local/ups/etc/upsd.users

sudo /usr/local/ups/sbin/upsdrvctl -u pi start

sudo /usr/local/ups/sbin/upsd -u pi -4

### END CONFIG FILE CHANGES / STARTUP ###


## TESTING DUMP! ##

# Plugged into 120v outlet ...
pi at raspberrypi ~/nut $ /usr/local/ups/bin/upsc SMART500RT1U at localhost
battery.voltage.nominal: 12
device.mfr: Tripp Lite
device.model: SMART500RT1U
device.type: ups
driver.name: tripplite_usb
driver.parameter.pollinterval: 2
driver.parameter.port: auto
driver.version: 2.7.2-signed-19-g90e2790
driver.version.internal: 0.24
input.voltage.nominal: 120
outlet.1.desc: Load 1
outlet.1.id: 1
outlet.1.switch: 1
outlet.1.switchable: 1
outlet.2.desc: Load 2
outlet.2.id: 2
outlet.2.switchable: 0
ups.debug.D: 00 79 00 8b 0d 00 00 '.y.....'
ups.debug.L: 00 00 00 07 58 58 0d '....XX.'
ups.debug.load_banks: 1
ups.debug.M: 00 74 00 7f 0d 00 00 '.t.....'
ups.debug.P: 30 30 35 30 30 58 0d '00500X.'
ups.debug.S: 01 04 00 00 64 00 0d '....d..'
ups.debug.T: 20 00 02 57 01 58 0d '...W.X.'
ups.debug.V: 02 00 0c 01 58 58 0d '....XX.'
ups.delay.shutdown: 64
ups.firmware: F334401
ups.firmware.aux: protocol 3005
ups.id: 0
ups.mfr: Tripp Lite
ups.model: SMART500RT1U
ups.power.nominal: 500
ups.productid: 0001
ups.status: OL
ups.vendorid: 09ae

# UNPLUGGED!
pi at raspberrypi ~/nut $ /usr/local/ups/bin/upsc SMART500RT1U at localhost
battery.voltage.nominal: 12
device.mfr: Tripp Lite
device.model: SMART500RT1U
device.type: ups
driver.name: tripplite_usb
driver.parameter.pollinterval: 2
driver.parameter.port: auto
driver.version: 2.7.2-signed-19-g90e2790
driver.version.internal: 0.24
input.voltage.nominal: 120
outlet.1.desc: Load 1
outlet.1.id: 1
outlet.1.switch: 1
outlet.1.switchable: 1
outlet.2.desc: Load 2
outlet.2.id: 2
outlet.2.switchable: 0
ups.debug.D: 00 00 00 84 0d 00 00 '.......'
ups.debug.L: 00 00 00 07 58 58 0d '....XX.'
ups.debug.load_banks: 1
ups.debug.M: 00 00 00 7f 0d 00 00 '.......'
ups.debug.P: 30 30 35 30 30 58 0d '00500X.'
ups.debug.S: 01 04 00 01 64 00 0d '....d..'
ups.debug.T: 20 00 00 00 01 58 0d '.....X.'
ups.debug.V: 02 00 0c 01 58 58 0d '....XX.'
ups.delay.shutdown: 64
ups.firmware: F334401
ups.firmware.aux: protocol 3005
ups.id: 0
ups.mfr: Tripp Lite
ups.model: SMART500RT1U
ups.power.nominal: 500
ups.productid: 0001
ups.status: OB
ups.vendorid: 09ae

# Replugged!
pi at raspberrypi ~/nut $ /usr/local/ups/bin/upsc SMART500RT1U at localhost
battery.voltage.nominal: 12
device.mfr: Tripp Lite
device.model: SMART500RT1U
device.type: ups
driver.name: tripplite_usb
driver.parameter.pollinterval: 2
driver.parameter.port: auto
driver.version: 2.7.2-signed-19-g90e2790
driver.version.internal: 0.24
input.voltage.nominal: 120
outlet.1.desc: Load 1
outlet.1.id: 1
outlet.1.switch: 1
outlet.1.switchable: 1
outlet.2.desc: Load 2
outlet.2.id: 2
outlet.2.switchable: 0
ups.debug.D: 00 79 00 81 0d 00 00 '.y.....'
ups.debug.L: 00 00 00 07 58 58 0d '....XX.'
ups.debug.load_banks: 1
ups.debug.M: 00 00 00 7f 0d 00 00 '.......'
ups.debug.P: 30 30 35 30 30 58 0d '00500X.'
ups.debug.S: 01 04 00 00 5a 00 0d '....Z..'
ups.debug.T: 20 00 02 58 01 58 0d '...X.X.'
ups.debug.V: 02 00 0c 01 58 58 0d '....XX.'
ups.delay.shutdown: 64
ups.firmware: F334401
ups.firmware.aux: protocol 3005
ups.id: 0
ups.mfr: Tripp Lite
ups.model: SMART500RT1U
ups.power.nominal: 500
ups.productid: 0001
ups.status: OL
ups.vendorid: 09ae
pi at raspberrypi ~/nut $


Steve Ballantyne
Network Engineer
MCSE/MCDST; Novell CLA; LPIC-1; CTT+; A+; Network+; Linux+; Server+;
I-Net+; Security+; SonicWALL CSSA

Reasonably Related Threads

Search for more apparently analagous threads

Nut upsuser - Jun 2014 - The dreaded Tripp Lite SMART500RT1U and NUT

[Nut-upsuser] The dreaded Tripp Lite SMART500RT1U and NUT

[Nut-upsuser] The dreaded Tripp Lite SMART500RT1U and NUT

[Nut-upsuser] The dreaded Tripp Lite SMART500RT1U and NUT

[Nut-upsuser] The dreaded Tripp Lite SMART500RT1U and NUT

Reasonably Related Threads