similar to: PowerWalker VFI 3000RT LCD: Device or resource busy

Hello, I have just installed nut_2.6.0 from Debian testing, do anyone know the correct driver for this ups? The blazer_usb don't report battery-charge, the bundled software report charge and runtime. root at pluto<~>upsc powerwalker battery.voltage: 40.86 battery.voltage.nominal: 36.0 beeper.status: enabled device.mfr: device.model: HV 1K device.type: ups driver.name: blazer_usb

Hi all, I have problem with UPS from PowerWalker model VFI 2000 RT LCD over USB (didn't try serial yet). UPS should work via HID driver but ups.status is not rendered properly. Specification of UPS says USB HID compatible. HID driver is the only one which talks with UPS as i try a few from /lib/nut. I use driver usbhid-ups (which communicate with ups), but subdriver resolving is

Hello! I'm trying to use nut with a Ippon Smart Winner 3000 UPS (http://shop.key.ru/photo/items/45535.jpg) which looks like a custom-labeled OEM model of the megatec branch. I tried both the megatec_usb and the blazer_usb drivers for it, with a obvious config section: [ippon] driver = blazer_usb port = auto vendorid = 06da productid = 0003 desc = "Ippon Smart Winner 3000" If I

Hi Arnaud and NUT team You may recall some time ago, I and a few others posted questions about the above referenced (cheap and cheerful) USB-based UPS - specifically regarding FreeBSD USB support in NUT. The original posting was entitled "Zigor Ebro 650 compatibility". I've since tried the latest Windows port of NUT with my WinXP laptop connected to the Zigor Ebro and finally

> > hmm, apparently the UPS doesn't close the replies to our queries with > the expected CR and we (I) did not consider that case in nutdrv_qx -- > noted: > https://github.com/networkupstools/nut/issues/441 > > But blazer_usb, being less strict on the terminating CR of Q1 replies, > should work with your device. > > > root at artu:~# upsc Elit at artu > >

Hello, I have two UPS from PowerWalker: VFI 1500RM LCD and VFI 3000RM LCD both equiped with SNMP card, but NUT with snmp-ups does not support them. PowerWalker declare support RFC1213, RFC162 but there is a problem with some snmp values: # upsdrvctl start Network UPS Tools - UPS driver controller 2.6.4 Network UPS Tools - Generic SNMP UPS driver 0.66 (2.6.4) Detected 3K on host 10.0.0.236

Hello, I have a UPS branded as "Energit MXE II" that comes with the infamous Winpower software (as already discussed in this old thread <http://nut-upsdev.alioth.debian.narkive.com/m0FWk43o/blazer-usb-compatibility-with-ippon-backpro-upses-phoenix-power-co-ltd-usb-to-serial-controller>). This same UPS appears to be sold as "Centralion Titan Elite" and maybe other names

I'm running Ubuntu 14.04.1 with nut 2.7.1-1ubuntu1, using a Powerwalker/INNO TECH ups. It used to working fine, but lately blazer_usb just executes a few commands and then terminates with a "Got disconnected by another driver" message. Any suggestions? Example output from blazer_usb with loads of debug: # /lib/nut/blazer_usb -DDDDDDDDDDDDDDDDDDDDDD -a nasups Network UPS Tools -

Hi to everyone! I'm posting here after digging around the nut-upsuser and nut-upsdev mailing list, hoping I didn't miss something important. I'm trying to make my ups working with nut: it's a Tecnoware ERA LCD 0.85 which uses the so-hated UPSilon 2000 software to connect via usb. Personally I checked and seems that this junk software only works from windows, I'm trying to

Hi to all and happy new year! I'm writing here as I'm trying to get nut supporting the UPS in the subject; I didn't check well before buying and nowI discovered this is kinda bad hardware (it doesn't have a valid USB id, it just reports 0000:0001 and linux support doesn't really work as they stated), but before changing it I wanted to try to find a solution to get it work with

Merry Christmas to you all and best wishes! I ran into exactly the same problem as described. OS: FreeBSD 9.0-Rel UPS: Eaton E-Series NV 600H NUT: from Ports, nut-2.6.5_1 driver: blazer_usb I am sure the problem is not permission-related as it occurs even when the driver runs as root. My tested recipe for USB permissions is: 1. run usbconfig to find where the device is connected. In my case:

Hello guys, Please help me to resolve the issue. I bought 'SVEN Power Pro+ 500 USB' UPS few days ago and tried to setup NUT 2.6.0 to work with it. blazer_ups driver doesn't recognize the UPS :( The Manufacturer provides 'PowerD' software for linux with installation instractions on a CD (see example below). --------===------- Welcom to PowerManager System!

hi! When I turn on my pc everything works fine, but if I restart fails (I'm not sure if this is true at 100%)?(then, i can do 'sudo /etc/init.d/nut restart' and it works) But what is certain is that sometimes when start up the pc it works and sometimes fails, can be a problem with the start time (i have a fast ssd) and the initialization of the driver and the usb port? thanks! syslog:

@fsp Please forward to development, manufacturing and quality management department: Model EP1000(PPF6000/100), 431107300095, 4711140480534, Art-Nr. 8296861, 70539, 14Z00000, 35-0200116-01G @nut-users http://www.networkupstools.org/ 2.4.3 debian stable, 2.6.2 upstream, linux 2.6.38-debian-bpo # /usr/local/src/nut-2.6.2/drivers/blazer_usb -u root -DDDDD -a ups Network UPS Tools - Megatec/Q1

Hi, I am unable to get my UPS working with NUT. Information: lsb_release -a: Distributor ID: Raspbian Description: Raspbian GNU/Linux 8.0 (jessie) Release: 8.0 Codename: jessie apt-cache policy nut-server: nut-server: Installed: 2.7.2-4 Candidate: 2.7.2-4 Version table: *** 2.7.2-4 0 500 http://mirrordirector.raspbian.org/raspbian/ jessie/main armhf Packages

On 10/08/2012 21:58, nut-upsuser-request at lists.alioth.debian.org wrote: >>> Arnaud Quette<aquette.dev<at> gmail.com> writes: >>>> 2012/6/3 Chris Rees<crees<at> freebsd.org>: >>>>> Hi all, >>>> Hi Chris, >>>> >>>>> After some research I've found that this device should run with the

Hi I Bought a cheap Plexus 800VA UPS from ebuyer : http://www.ebuyer.com/product/240319 to use with my Netgear ReadyNAS duo. Initial version of NUT was very old and NAS didn't detect it although in the NAS log it said "UPS Disconnected". Syslog did send the following : Jan 25 12:46:36 nas-27lfc kernel: usb 1-1: new low speed USB device using uhci_hcd and address 2 Jan 25 12:46:37

Hi all, I've bought UPS FSP EP 850 because I have similar UPS, FSP EP 1000. It is working on my other server with with Fedora 14, kernel 2.6.35.14-106.fc14.x86_64 and installed nut-2.6.2-1. My new UPS is detected by kernel (see below lsusb output) and is partially detected by blazer_usb driver also. But it doesn't communicate with driver (see below blazer_usb output). I run all

> We need to make sure this isn't something vm-related I suspect that this is definitely vm related now. I've tried Ubuntu server 10.10 as you suggested, and also Debian wheezy and both do the same thing. I saw in another thread that the author of the .vib of nut for ESXi is on this mailer - hopefully he can shed some light on what's happening. I would even be happy if I can

Hi, The UPS is now connected via HID-USB, but seems to randomly disconnect. Sometimes after a few hours, other times days... Any suggestions? -------- Original Message -------- Subject: Re: [Nut-upsuser] Powerwalker VI 2200VA LCD Local Time: October 2, 2016 11:50 PM UTC Time: October 2, 2016 9:50 PM From: hyouko at gmail.com To: Lars de Bruin <lars at larsdebruin.net> nut-upsuser