similar to: [OT] Does Energy Savings mode exist with BRI/PtP ?

Hello, I'm a graduate student. We are setting up an IVR system for research purpose on a BRI channel. (We can't afford PRI line as its cost is about 10x of the BRI). The line will be connected to the CTI card. Using asterisk server we will be recording the calls. I'm confused about whether we should apply for point-to-point connectivity or point-to-multipoint. P2P costs more than

Hi list! I am installing an * box that will be installed on a site with KPN BRI ISDN in The Netherlands. I am using bristuff fron Junghanns. Does anybody know the correct settings for this? I will not have internet access there which makes it harder to google around on location. switchtype = euroisdn is pretty obvious but what about these settings: signalling = bri_cpe_ptmp ; p2p TE mode

hello: thanks for Tzafrir Cohen for dahdi testing. I installed dahdi-2.1-r3c svn code and asterisk1-6 for testing OpenVox B400P and junghans card. i fund that there is bug (i think) to dectect NT or TE mode. actually on the board, i set it as TE mode, but after start wcb4xxp, but it show the port is NT mode. to detect the TE mode, I modefy the code in base.c

Is there a recommended way to find out the cause of DIALSTATUS = CONGESTION for PRI/BRI channels? Currently I am evaluating the DIALSTATUS variable and I also count the active ISDN channels for the ISDN trunk in question. Counting the active ISDN channels seems somewhat clumsy as the mapping to a specific trunk must be done by hand (or write even more code). I have a setup where outgoing calls

Hello, If my understanding is correct, these days it seems that many ISDN BRI lines are configured in energy saving mode in which signalling D-channel is "dropped" until a new call comes in. Is it possible to replicate this behaviour with Asterisk (when Asterisk is in NT mode and is seen as a public ISDN by another PBX, for instance) ? If not, would you it would be a useful addition to

Hi I have a small ISDN PABX , (BRI) at home - Siemens Gigaset 4175 which has cordless DECT extensions. I have set up asterisk on FC3 with two HFC cards and I am using the latest bristuff. I am trying to use * between my ISDN line and my PABX. One card is in TE mode and can receive and make calls OK. I can make and receive external calls to a SIP phone. I cannot get the other card to talk to my

Hi, When startin * it tells me: ================================ [chan_zap.so] => (Zapata Telephony w/PRI) == Parsing '/etc/asterisk/zapata.conf': Found Sep 3 17:21:59 DEBUG[1076873856]: chan_zap.c:1208 update_conf: Updated conferencing on 1, with 0 conference users -- Registered channel 1, PRI Signalling signalling Sep 3 17:21:59 DEBUG[1076873856]: chan_zap.c:1208 update_conf:

Hi, I'm trying to connect quadbri between powered ISDN phone and ISDN line: ISDN <---1---> TE - * - NT <--2--> Phone I use quadbri, suse 9.2 and latest 0.2.0-RC7k bristuff. I've used sample settings provided with package, but do get strange error (I think that I have wrong setting for P2P or P2MP setting and cables 1 and 2). If I connect phone to ISDN with straight cable

Hi! Has anybody seen anything like this using zaphfc? On outgoing calls (via isdn) , the line gets hung-up as soon as the called party answers. As seen below i get some protocol error (6) - but i'm not sure if this is related to the "hang-up" which apparently comes a little earlier?! Incomming calls on the isdn (zaphfc) interface is working just fine (P.S. what about the

Hi! I'm goining to connect an AVM C4 to 4 BRI-lines in PTP-Mode, all BRI-lines will have the same number (1234-XX for example). I don't know if this is possible and I can't test it, because I don't have these lines yet. Is anybody out there, running such a configuration? I'm looking for some example configs. Especially I want to know how it is possible, to let asterisk

Hallo all, I am trying to get * with chan_capi and a ptp-ISDN with 4 lines on a AVM C4 card to work. But weather inbound nor outbound is working :( My capi.conf: ; ; CAPI config ; ; [general] nationalprefix=0 internationalprefix=00 rxgain=0.8 txgain=0.8 [interfaces] mode=immediate isdnmode=ptp msn=8993 incomingmsn=* mode=immediate controller=1,2,3,4 softdtmf=1 ;accountcode= context=demo

Hi, i've downloaded/compiled/installed the bristuffed asterisk Asterisk 1.0.7-BRIstuffed-0.2.0-RC8a and i'm using it with an hfc card. It runs on a debian 3.1 sarge machine with kernel 2.6.11. Asterisk works well if i configure the card using isdn4linux. I'm having problems dialing out (not tried the input yet). This is the output from asterisk: -- Accepting AUTHENTICATED call from

Hi, I am using Asterisk on a DSS1 ISDN-BRI with ISDN4Linux (and a Fritz Card PnP). The ISDN-BRI is in PTP-Mode (Point to Point "german: Anlagenanschluss") which is enabled within I4L with "hisaxctrl fcpcipnp0 7 1". Everything works fine except that I can not see the called number/MSN of incoming calls within Asterisk and because of this I can not route incoming calls

Hello, I have an installation in Austria; ISDN service provided by Austria Telekom. The main number of the service is 6 digits. Incoming calls may contain 2 additional digits, which I then use to route the call to the correct extension. Telekom sends me all the digits. My problem is that when someone tries to dial an 8 digit number to an extension from an outside analog phone, AT sends the call

O.K. thanks a lot, Felix and Peer Oliver. But somehow asterisk keeps telling me while startup: [chan_capi.so] => (Common ISDN API for Asterisk) Jan 24 14:30:47 NOTICE[9796]: chan_capi.c:3271 load_module: Unused contr1 Jan 24 14:30:47 NOTICE[9796]: chan_capi.c:3271 load_module: Unused contr2 Jan 24 14:30:47 NOTICE[9796]: chan_capi.c:3271 load_module: Unused contr3 Jan 24 14:30:47

Hi ! I've fetched a spare AVM B1 card from the cellar, and installed it. After "modprobe b1pci" I did "capiinit" and capiinit moaned about a missing t1.b4. So I search the web and found one at http://www.avm.de/ftp/cardware/b1/x_misc/ddi/. When I now look at the controller, I finally see p2p-mode: # cat /proc/capi/controllers/1 name b1pciv4-a400 io

Hi- Anyone using the Junghann's quad BRI card and the Digium E100P in the same system? I'm having a configuration problem where I can configure the cards one at a time (with the appropriate drivers loaded) in a system, but when I try them both together, neither will work. They both work fine one at a time. Probably has something to do with the channel numbering. I've tried

Has anyone a working /etc/asterisk/capi.conf example for Germany or Switzerland using the AVM C4 - ISDN Card. I try to connect asterisk to 3 wires BRI-ISDN (Swisscom). I appreciate your help and it would save me a lot of time, figuring it out by myself. regards, Claudio

Hi All ... I'm running Asterisk 1.2.13-BRIstuffed-0.3.0-PRE-1v which has a Junghanns QuadBri card in it (lspci reports Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01)) I have a regular KPN ISDN2 Line connected which works fine with the the zapata.conf below. However, I also have a new KPN ISDN Mutli (meervoudig) line (PBAX-Group), which works fine for incoming calls,

Hi, I need to rebuild a system which has 4 BRI ports and is connected to Point-to-multiPoint lines, in a country where telco often "drop lines for energy savings". I'm planning to use latest 11.4.0 asterisk version along with dahdi and libpri (no misdn). Which version are recommended for Dahdi and Libpri ? My main requirements are, beside having calls coming in and out: - keep a