asterisk users - Oct 2006 - PBAX-Group with QuadBRI card, outgoing call problem

Hi All ...

 I'm running Asterisk 1.2.13-BRIstuffed-0.3.0-PRE-1v  which has a
Junghanns QuadBri card in it (lspci reports  Cologne Chip Designs GmbH
ISDN network Controller [HFC-4S] (rev 01))

I have a regular KPN ISDN2 Line connected which works fine with the
the zapata.conf
below.

However, I also have a new KPN ISDN Mutli (meervoudig) line (PBAX-Group),
which works fine for incoming calls, however, is not able to successfully make
an outgoing call. I get a 'busy/congested'.

When I do a bri debug I have the following, any help on what I can do to setup
this is welcome!

Regs,

gd



Enabled debugging on span 3
    -- Executing Dial("SIP/gdevlet-089534a8",
"ZAP/8/06xxxxxxxxx") in new stack
3 -- Making new call for cr 132
    -- Requested transfer capability: 0x00 - SPEECH
3 > Protocol Discriminator: Q.931 (8)  len=51
3 > Call Ref: len= 1 (reference 4/0x4) (Originator)
3 > Message type: SETUP (5)
3 > [04 03 80 90 a3]
3 > Bearer Capability (len= 5) [ Ext: 1  Q.931 Std: 0  Info transfer
capability: Speech (0)
3 >                              Ext: 1  Trans mode/rate: 64kbps,
circuit-mode (16)
3 >                              Ext: 1  User information layer 1: A-Law (35)
3 > [18 01 8a]
3 > Channel ID (len= 3) [ Ext: 1  IntID: Implicit, Other Spare: 0,
Exclusive Dchan: 0
3 >                        ChanSel: B2 channel
3                          ]
3 > [28 0c 47 69 72 61 79 20 44 65 76 6c 65 74]
3 > Display (len=12) [ Giray Devlet ]
3 > [6c 06 00 81 33 31 30 31]
3 > Calling Number (len= 8) [ Ext: 0  TON: Unknown Number Type (0)
NPI: Unknown Number Plan (0)
3 >                           Presentation: Presentation permitted,
user number passed network screening (1) '3101' ]
3 > [70 0b 80 30 36 32 34 32 36 32 38 36 37]
3 > Called Number (len=13) [ Ext: 1  TON: Unknown Number Type (0)
NPI: Unknown Number Plan (0) '0624262867' ]
3 > [7d 02 91 81]
3 > High-layer compatibilty (len= 4) [ 3 0x91 3 0x81 3  ]
    -- Called 8/06xxxxxx
3 No response to SETUP message
3 NEW_HANGUP DEBUG: Calling q931_hangup, ourstate Call Initiated,
peerstate Overlap sending
    -- Channel 0/2, span 3 got hangup, cause 18
3 NEW_HANGUP DEBUG: Destroying the call, ourstate Call Initiated,
peerstate Overlap sending
3 NEW_HANGUP DEBUG: Calling q931_hangup, ourstate Call Initiated,
peerstate Overlap sending
    -- Hungup 'Zap/8-1'
  == Everyone is busy/congested at this time (1:0/0/1)
  == Auto fallthrough, channel 'SIP/gdevlet-089534a8' status is
'CHANUNAVAIL'


--------------------


/etc/asterisk/zapata.conf
switchtype = euroisdn
; p2mp TE mode (for connecting ISDN lines in point-to-multipoint mode)
signalling = bri_cpe_ptmp

pridialplan = unknown
prilocaldialplan = unknown
overlapdial=yes
nationalprefix = 0
internationalprefix = 00
;usecallingpres=yes
callerid=asreceived
;priindication = passthrough

echocancel = yes
echocancelwhenbridged = yes
echotraining = 100


context=isdn-incoming
; S/T port 1 - 4
channel => 1-2

On 10/25/06, Giray Devlet <giray.devlet@bitbrains.nl>
wrote:
>
> /etc/asterisk/zapata.conf
> switchtype = euroisdn
> ; p2mp TE mode (for connecting ISDN lines in point-to-multipoint mode)
> signalling = bri_cpe_ptmp
>
Have you tried "signalling = bri_cpe" if you have a group of ISDN
channels, they are more often in a PTP mode than a PTMP.

Just a thought.
Steve

Hi Steve,

 THX!!! This works ...  couldn't really find anywhere what other
options I could use as values for signalling ... thx!

gd

From: "Steve Davies"
<davies147@gmail.com>
>On 10/25/06, Giray Devlet <giray.devlet@bitbrains.nl> wrote:
>>
>> /etc/asterisk/zapata.conf
>> switchtype = euroisdn
>> ; p2mp TE mode (for connecting ISDN lines in point-to-multipoint mode)
>> signalling = bri_cpe_ptmp
>>
>
>Have you tried "signalling = bri_cpe" if you have a group of ISDN
>channels, they are more often in a PTP mode than a PTMP.
>
>Just a thought.
>Steve