similar to: Newbie Polycom: Cannot conference with >10 digit 3rd party

Hi all. I just installed bunch of IP450's and everything went well and my customer is happy.... except that they are unable to transfer calls to other extenstions. They can dial them directly just fine. However, when the user is in a call and presses the transfer soft key, they get dial tone, and start typing the extension, say 1008. But by the time they get 100 typed in, the phone tries

Any Polycom gurus out there? If so, I have a few config file questions. First off, does anyone have the daylight savings time rules written for this Sunday's big change? Secondly, if there any way in the config file to tell the phone not to display the number of missed calls? I don't mind it keeping the missed calls list, I just don't want that running count. Lastly, I am trying

Hi All, I'm not sure if this is related directly to asterisk or not but on my Polycom 320 when I try to dial a number smaller than 4 digits I get an error on the phone saying "Enter more digits". The dial plan section is listed below. <dialplan dialplan.impossibleMatchHandling="0" dialplan.removeEndOfDial="1"> <digitmap

hi there I'm setting up asterisk@home and I'm using Polycom IP 500 phones. When I call a number that has a digital receptionist (i.e. "dial 1 or such and such, dial 2 for this and that...") the Polycom doesn't seem to send the extra digits. When I try it with X-Lite things appear to work fine, so I think the problem is with the Polycom configuration. Here's some

I'm stumped on this one and any help would be greatly appreciated. I'm just trying to get my Polycom 601 to have multiple extensions on it. For example, on line 1 I want extension 21, on line 2 I want extension 22, and on line 3 I want extension 23. Ideally I'd actually have each extension appear on 2 lines and therefore filling up all 6. I should be able to do that with the

I recently had a bear of a time getting a Polycom Soundpoint 500IP up and registered.. Now that its registered I ran into a problem w/ the dialplan. Needing to dial x101 I'd dial 10 - then get a fast buzy.. Also making a local call - dialing 95551212- would give me a fast busy after the 7th digit - so 9555121.. Same w/ LD calls... This dialplan really got me down as I didn't find

I'm using Polycom Soundpoint phones and I want to use some extensions beginning with # for features setup. I'm getting the fast busy "can't match it" signal. I want to match #50 for call forwarding, for instance, and #505551212 to set the call forwarding number and turn it on. I have tftp set up and sip.cfg contains the following: <dialplan

I'm replacing a SoundPoint IP 600 with a SoundPoint IP 650. I attempted to simply reuse the existing config files for the old phone on the new phone, but the new phone would lock up on the 4th digit when attempted to dial out certain numbers. So, I downloaded the newest firmware and config templates from Polycom, and attempted to migrate the settings. Seems I'm missing something from

I have four Polycom 330 phones connected to an asterisk system. There are other VoIP phones connected too. All of the extensions are four digits beginning with 11. From any of the phones, except the Polycom, picking up the handset to call extension 1103 for example works fine. With the Polycom 330, as I press the second 1 of 1103 it stops taking input and gives me an error. I tried

I am having a strange problem with polycom 501 and dailing. I've read the archives and no one there specifically mentions this problem, so I thought I'd ask here. The problem is that when the user picks up the receiver or pressed new call, sometimes they will enter a number (for example 95072091234) and in the middle of the number the cursor might jump back one digit. So the call above,

Are all of the sip phones in the same context? > -----Original Message----- > From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users- > bounces@lists.digium.com] On Behalf Of Robert Jenkins > Sent: Tuesday, January 16, 2007 1:44 PM > To: 'Asterisk Users Mailing List - Non-Commercial Discussion' > Subject: [asterisk-users] Polycom IP601 - some hints working,

This is a dialpaln issue. I solved the same problem recently. For 4 digit extensions you need to append the dialplan statement in the sip.cfg configuration file as follows <digitmap dialplan.digitmap="[2-9]11|0T|011xxx.T|[0-1][2-9]xxxxxxxxx|[2-9]xxxxxxxxx|[2 -9]xxxT|1xxxT" dialplan.digitmap.timeOut="3"/> Michael > I am not sure what I did but blind transfers do not

I'm having a problem with polycom ip601. If I Dial() directly eg Dial(SIP/4000) it works perfectly. The polycom rings, and stops ringing as soon as I hang up. But if the phone is called via a queue, the polycom continues to ring long after I've hung up. Other phones in the queue (grandstream, cisco) don't have this problem, and stop ringing properly when I hang up. polycom bug

I was reading a Polycom brochure and it appears that there is really no special receptionist console and the console is basically a IP601. Is this correct? The only difference is to purchase an expansion module in order to have more shortcut keys for the girls. So, apart from the hardware, as far as the dialplan is concerned, do I just treat the receptionist console as any other extension? Are

Make sure you set nat=yes for the sip user. Asterisk will then send replies back to the source IP address, rather than what's in the Via: header. > -----Original Message----- > From: Warren (mailing lists) [mailto:warren-lists@icruise.com] > Sent: Friday, October 27, 2006 5:45 AM > To: Asterisk Users Mailing List - Non-Commercial Discussion > Subject: [asterisk-users] Taking a

I was hoping that someone may be able to shed some light on some issues I'm having on trying to get an Asterisk test server up and running. At the moment I have the basics, two Polycom hard phones (301 & 601 with expansion unit (which oddly will not power up)) that can call each other, log into voicemail (one touch) and have custom directories & buddy lists. Unfortunately some of the

How do you disable call waiting on Polycom IP601 phones? I've looked through the user and admin guides and can't see anything about disabling it. -Dan

Hello people, I am having difficulties figuring out the POE power draw in watts from a Polycom IP601. I want to know how many IP601's can be powered from the Cisco Catalyst 3560G-48PS. The IP601 wallwart has: Input 120VAC 60hz 19W, Output 24VDC 500mA. I assume the output is appropriate value to figure out how many phones can be powered. The Cisco 3560 datasheet says "the 48-port PoE

I'm working on replacing a SoundPoint 600 with a 650. I need to merge these two sets of digitmaps in the polycom sip.cfg file, because the 650 locks up when I try to use the digitmap from the 600. I've included the default digitmap from a 3.1.3 RevB polycom release. I'd like to merge these two digitmaps, but I don't want to reintroduce the lockup issue I was having with the

> >> Jason Brown wrote: > >> | Anyone have experiece with polycom phones? > >> | > >> | I am experiencing a really weird problem. In an office > where I have > >> | the following extensions: > >> | On the Polycom phones, when I want to dial from extension > >> 100 to any > >> | extension 120 or above, or dial out, it