Displaying 20 results from an estimated 3000 matches similar to: "Unable to create channel of type 'Zap' with ecmg2 and kernel 2.6.23"
2009 Feb 25
4
TE121 on Asterisk
Hello, I just bought a TE121 T1/E1 card, and now trying to install it on a
1.4.23.1 asterisk with dahdi 2.1.0.4
Actually first everything went on well and i managed to see my card on dahdi.
Here's the output:
#asterisk# dahdi_hardware
pci:0000:04:08.0 wcte12xp+ d161:8000 Wildcard TE121
and this is the scan:
--------------------------
asterisk# dahdi_scan
[1]
active=yes
alarms=RED
2005 Sep 19
1
problems with PRI
Hi, I configured an asterisk box with 1
Digium Wildcard TE110P T1/E1 Card 0
I setup the jumper in e1 position.
my zaptel.conf :
defaultzone=it
loadzone=it
#gestione PRI
span=1,0,0,ccs,hdb3,crc4,yellow
bchan=1-15 # set this to 1-15,17-31 for E1
dchan=16 # set this to 16 for E1
bchan=17-31 # set this to 1-15,17-31 for E1
#
Asterisk starts correctly, I see th 30 channels.
Anyway I cannot put
2005 Sep 16
0
Zap failed
I have configured /etc/asterisk/zapata.conf, but now Asterisk refuses to
start:
Asterisk 1.0.9, Copyright (C) 1999-2004 Digium.
Written by Mark Spencer <markster@digium.com>
....
[chan_zap.so] => (Zapata Telephony w/PRI)
== Parsing '/etc/asterisk/zapata.conf': Found
Sep 16 20:36:51 ERROR[6750]: chan_zap.c:6246 mkintf: Unable to get
parameters
Sep 16 20:36:51 ERROR[6750]:
2005 Mar 18
0
T100P: Can't Make/Receive Zap Calls (Long Newbie Blah)
All,
Alright, I've looked around the internet, the voip-info.org wiki, and
browsed the contents of this mailing list. While I've found a couple of
scenarios that are close to this one, I haven't found one that uses my
particular card (T100P). Without further delay --
I have successfully configured internal SIP services between a Snom 200
and a Windows X-Lite client and have
2008 Feb 26
6
[URGENT] Zap channels fail to load
I have spent some time this morning trying to add an Astribank to our
current Asterisk, but it failed, so I just removed the hardware,
restore the config files to the original setup and started asterisk.;
I could see that no Zap channels are started so I did load chan_zap.so:
pbx*CLI> module load chan_zap.so
[Feb 26 10:32:18] WARNING[3809]: pbx.c:2968 ast_register_application:
Already have an
2009 Mar 27
4
Help: RED alarm on Wildcard TE122 card
Hi, I have been trying to get a Wildcard TE122 card running here the
last couple of days.
libpri and zaptel are all installed and configured to E1 specs. The
jumper on the card is on, so configured for E1 (I'm in Norway).
When running zttool, I get 'Alarms: RED' on the single card installed.
Other information in zttool:
Current alarms: Red Alarm
Sync source: Internally clocked
2007 May 21
1
CAS signalling conflicts with Clear channel
Hi,
My asterisk server was working with a 4-FXO analog
card (TDM400P).
I recently added two digital cards: a TE120P (1 PRI)
and a B410P (4 BRI).
The B410P is still unconfigured but inserted in a PCI
slot.
The TE120P's jumper is set to E1 as it will connect to
a commercial PBX's PRI card also configured as E1.
My analog channels used to be 1-4 but since I added
the new cards I changed
2007 Jul 28
1
Query1
Hi,
I am facing problem in configuring D-channel for TE120P card.I did the
following things
/etc/zaptel.conf
span=1,1,0,ccs,hdb3
bchan=1-15,17-31
dchan=16
/etc/asterisk/zaptel.conf
group=1
signalling=pri_cpe
2010 Nov 27
1
DAHDI 2.4.0 produces HDLC errors with echo canceler
Hi,
After upgrading to DAHDI 2.4.0 from Zaptel, I noticed a lot of HDLC
errors on my console:
[Nov 27 01:15:09] NOTICE[2743] chan_dahdi.c: PRI got event: HDLC Bad
FCS (8) on Primary D-channel of span 1
[Nov 27 01:15:09] NOTICE[2743] chan_dahdi.c: PRI got event: HDLC Abort
(6) on Primary D-channel of span 1
These errors prevented calls from being made and received on my PRI spans.
This seems
2020 Sep 06
0
dahdi_cfg -vvv error , PRI show spans command not found
dahdi_cfg -vvv error `cut: '/sys/bus/dahdi_devices/devices/pci:0000:01:00.0/spantype': No such file or directory`
PRI show spans --command not found
test call not working.
-- dahdi_genconf -vvv
Default parameters from /etc/dahdi/genconf_parameters
Generating /etc/dahdi/assigned-spans.conf
cut: '/sys/bus/dahdi_devices/devices/pci:0000:01:00.0/spantype': No such file or
2009 May 27
3
1.6.0.9: Now "Unable to create ... 'DAHDI'"
Still trying to upgrade to 1.6.0.9 for 1.4.
It worked - it worked all day yesterday, but this morning:
-- Executing [646xxxyyyy at longdistance:1]
Answer("SIP/172-08276a60", "") in new stack
..........
-- Executing [646xxxyyy at longdistance:6] Dial("SIP/172-08276a60",
""DAHDI/g2"/1646xxxyyyy") in new stack
May 27 09:56:57]
2009 Jan 12
2
a zaptel problem
Hello,
I have a problem with zaptel. I hope you can help me.
I installed and configure zaptel.
ZAPTEL.CONF
span=1,1,0,ccs,hdb3,crc4
bchan=1-15,17-31
dchan=16
loadzone = de
defaultzone=de
But the output of cat /proc/zaptel/*
Span 1: WCT1/0 "Digium Wildcard TE110P T1/E1 Card 0" (MASTER) HDB3/CCS/CRC4
RECOVERING
1 WCT1/0/1 Clear (In use) RED
2006 Mar 12
1
interop problem: "Missing handling for mandatory IE 24 (cs0, Channel Identification)"
Hi everybody,
I've connected Asterisk 1.2.5 (libpri 1.2.2, zaptel 1.2.4, Linux 2.6.13.2) to
an Avaya-Tenovis PBX via a PRI/E1-line. Calls from SIP-phones via * to the
PBX work fine. However, incoming calls to * only result in:
--
XXX Missing handling for mandatory IE 24 (cs0, Channel Identification) XXX
--
which seems to be an * problem, because a Windows-fax-machine works fine on a
PRI
2004 Aug 04
4
Problems with E100P
Hi,
I'm having trouble configuring and E1 link , I know the E1 is a PRI
and the switchtype is 5ess. The problem is that everytime I try to dial
I got and error saying that it was unable to open the zap channel .
Devices are created in the /dev/zap directory and I can open them with a
cat /dev/zap/1. I can also see the channels in /proc/zaptel/1.
Thanks in advance
[zaptel.conf]
2005 Aug 05
1
Problem running Astrerisk after defined card in /etc/asterisk/zapatal.conf
I have configured /etc/asterisk/zapata.conf, but now Asterisk refuses to start:
Aug 5 10:47:29 ERROR[1076842624]: chan_zap.c:5976 mkintf: Unable to get parameters
Aug 5 10:47:29 ERROR[1076842624]: chan_zap.c:9478 setup_zap: Unable to register channel '1-15'
Aug 5 10:47:29 WARNING[1076842624]: loader.c:328 ast_load_resource: chan_zap.so: load_module failed, returning -1
== Unregistered
2006 May 23
1
chan_zap.so error, asterisk stopped
Hi!I've a problem with asterisk,it doesn't start..it's stopped..I used the
amportal start command and this is the result:
SETTING FILE PERMISSIONS
Permissions OK
STARTING ASTERISK
Asterisk ended with exit status 1
Asterisk died with code 1.
Automatically restarting Asterisk.
Asterisk ended with exit status 1
Asterisk died with code 1.
Automatically restarting Asterisk.
2007 Sep 24
0
Asterisk Dropping Calls
Hello,
I am having an issue whereby calls are being dropped randomly. I have an
ISDN 30 E1 line going into a Wildcard TE220 (4th Gen). My Asterisk
install is based on Trixbox 2.0. However, I have updated the source code
to the following. The Asterisk release is asterisk-1.2.20. Zaptel
release is zaptel-1.2.18. And libpri release is libpri-1.2.4.
I have include an extract from the Asterisk log
2007 Sep 30
0
Asterisk Dropping Calls (Richard Young)
>
> Hi,
Remove
usecallingpres=yes
busydetect=yes
from your zapata.conf file. and the restart asterisk. Hopefully you will not
faced drop call issues.
Regards,
Vidura Senadeera.
Message: 3
> Date: Mon, 24 Sep 2007 12:29:40 +0100
> From: "Richard Young" <Richard.Young at intrintech.com>
> Subject: [asterisk-users] Asterisk Dropping Calls
> To:
2005 Sep 15
0
TE110P - Asterisk@Home Install Problems - Televantage 3 T1
I figured it out. The old system (Televantage 3 and 4 I think) has limited specifications on the T1. After setting up the system, I was able to send and recieve calls. I still have some work to do like figuring out faxing and a floating receptionist, but this is a nice start.
----------------------------------------------------Televantage T1 Requirements:
Framing: D4 Superframe or Extended
2006 Mar 31
1
Asterisk, QSIG and Tenovis PBX?
Hi,
we are still trying to properly connect a Tenovis PBX to an Asterisk server
(asterisk 1.2.6, libpri 1.2.2, zaptel 1.2.5, Digium Wildcard TE110P), this
time with QSIG.
Calling from a Tenovis phone to a SIP phone (i.e. traditional phone ->
Tenovis PBX -> QSIG -> Asterisk -> SIP phone) works with the following
messages:
---
Don't know what to do if second ROSE component is of