similar to: ztscan ports = zaptel channels ??

Hello, I've installed Asterisk and Asterisk GUI 2.0. The GUI says "No Analog Card found" and /etc/asterisk/ztscan.conf is empty. I see the following message from asterisk, <snip> -- Executing [executecommand at asterisk_guitools:1] System("Local/executecommand at asterisk_guitools-a145,2", "uptime >

Aloha, I'm not sure why I'm getting this error, but I can't seem to get chan_dahdi to load. SIP & IAX2 are working fine. Debian 4 w/ 2.6.28 kernel. Asterisk 1.6.1.5, dahdi-linux 2.2.0.2, dahdi-tools-2.2.0 CLI> module load chan_dahdi.so Unable to load module chan_dahdi.so Command 'module load chan_dahdi.so' failed. [Sep 1 10:57:51] WARNING[31696]: pbx.c:4550

Hi list, I'm trying to setup an asterisk 1.8.0 with MFC/R2, but I'm having these error messages loading chan_dahdi: > module load chan_dahdi.so ERROR[9241]: chan_dahdi.c:11848 mkintf: Signalling requested on channel 1 is MFC/R2 but line is in ISDN PRI signalling ERROR[9241]: chan_dahdi.c:16180 build_channels: Unable to register channel '1-15' I got the config in

Hello everybody, I try to install -Ubuntu 8.04 server- a B410P and a TDM2400P together with Asterisk 1.4.26-2, dahdi-linux-2.2.0.2 and dahdi-tools-2.2.0. Problem I face is the following one: CLI> module load chan_dahdi.so == Registered application 'DAHDISendKeypadFacility' == Registered application 'ZapSendKeypadFacility' == Parsing

I just had to move all my disk drives and PCI cards, including the Digium TDM400P, into a new box when the motherboard died. Now that the new box is up and running, my FXS ports no longer work although the FXO port does. I am hoping someone can help me diagnose and debug. I am running Fedora 8, asterisk asterisk-1.4.21, and zaptel-1.4.9 . Yes, I realize that this is old software and that zaptel

I have a box with 12 T1s (4 Te410P cards). The PSTN provider is reporting slips and ask me to update the clock source. I have my system.conf set as the following but when I run dahdi_scan only the ports on Card 1 are showing up with syncsrc=1 system.conf : span=1,1,0,esf,b8zs bchan=2-24 mtp2=1 span=2,2,0,esf,b8zs bchan=26-48 mtp2=25 span=3,3,0,esf,b8zs bchan=49-72

Hi everybody, I have a 1.6.0.5 asterisk system and I?m having many problems with my pstn cards. This system has a Digium B410P with 4 BRIs configured, and an OpenVox A400E. The issue is that it?s impossible to make the system recognize the A400E, despite the ?lspci? output is: 0a:00.0 Network controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface 11:00.0 ISDN controller: Digium,

I have spent some time this morning trying to add an Astribank to our current Asterisk, but it failed, so I just removed the hardware, restore the config files to the original setup and started asterisk.; I could see that no Zap channels are started so I did load chan_zap.so: pbx*CLI> module load chan_zap.so [Feb 26 10:32:18] WARNING[3809]: pbx.c:2968 ast_register_application: Already have an

Hi everybody, In an Asterisk 1.6.0.5, dahdi-linux-2.1.0.4, dahdi-tools-2.1.0.2, with a Digium B410P and an OpenVox A400E, I can't make "dahdi_scan" to recognize the OpenVox. This card was working correctly but suddenly stopped working and I cannot make it work again. Both ?lspci? and ?dahdi_hardware? detect it but ?dahdi_scan? not and I cannot use it. >lsppci: *0a:00.0

Hi all. I have this problem with my Digium 2E1 card and PRI, for hours It works well, with some meesages... [Aug 10 09:20:31] NOTICE[32270] chan_dahdi.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 But PRI continue up....hours later... PRI go down. I thought the problem was in the telco, but the strange thing is that I have a loop cable in the second E1 and when I scan both E1

Hi, I have a Junghanns QuadBri installed and seems to be detected and working correctly using the wcb4xxp driver All ports are configured as TE The problem is when I connect an ISDN line - the LED turns green and Dahdi status shows Alarm OK But when I try to make a call I get "All circuits are busy" cause 27 I have searched and web and tried numerous configs but it doesn't want to

Hi All, Sorry if this has been around a millions times.. I have been off this list for a few months now.. I have installed the latest asterisknow (upgraded asterisk to 1.6 as well) and I am having a hard time getting my X100P and TDM400P working.. Its all new to me with dahdi because my old server is still running Asterisk 1.0.2 so there have been lost of changes.. Can someone point me in

Hello! I am trying to configure my digium TE220 dual-span pci express card with Dahdi. I seemed to have managed to set up the card with the Dahdi kernel, as demonstrated by executing dahdi_scan: [1] active=yes alarms=RED description=T2XXP (PCI) Card 0 Span 1 name=TE2/0/1 manufacturer=Digium devicetype=Wildcard TE220 (4th Gen) location=Board ID Switch 0 basechan=1 totchans=31 irq=16

Hello, I have been struggling with the configuration of this card on my box. I have a T1 line and I am trying to setup asterisk with it. I followed all the instructions and I still see a blinking red light on the card. I use fedora 12. If everything is fine should I see a green line when I plug in the T1 line ? I want to isolate the issue so I di not start asterisk. When I run asterisk I get

Usually I used real Digium cards in asterisk systems, so I'm running into this for the first time. dahdi_tool reports that dahdi_dummy is in state UNCONFIGURED. This isn't super surprising, as it seems like the configuration files for DAHDI are really intended only for configuring real physical cards. But that begs the question: Is there any legal DAHDI configuration for dahdi_dummy such

Tengo en una maquia ubuntu 8.10 el kernel es Linux 2.6.27-14-generic Quiero configurar una tarjeta x100p i usarla con asterisk, asi que descague compile e instale lo siguiente: asterisk-1.4.24 dahdi-linux-2.1.0.4 dahdi-tools-2.1.0.2 libpri-1.4.9 Sin embargo no logro configurar la tarjeta con exito, ya probe casi? todo. Esto aparece si ejecuto lspci: 04:06.0 Communication controller: Motorola

TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and

Hi, I'm having problems with a TE420P card, in which I cannot make calls using spans 2 through 4. After a couple of days of working correctly, spans 2, 3 and 4 start failing (can not make calls). The system is configured to work with SS7. After the ACM message goes out, immediately a REL message is returned. I searched for error messages in /var/log/messages and could not find a clue

Hi again! I tried to attach two VoIP-phones to my new Asterisk 13.14.1 on a Banana PI with Armbian/Debian 9. First test was to call a test service that say the time. Works! Second test was to record my voice and play it again. Works! Third test was to call the other VoIP-phone. It does NOT work... :( Then I noticed that, by starting, Asterisk says the following messages: [Feb 15 18:42:54]

Hi list, After upgrading from Asterisk v1.2 to v1.4.14, all kinds Zaptel error messages related to my HFC-S PCI card disappeared, but now I can't access the card's resources because it always seems to be busy. Any idea why? Thanks, Jaap PS -- Below is some info regarding my configuration. =========================== Zaptel version: 1.4.7 (incl. firmware and modules). OS: Debian