similar to: ADIT TDM T1 <> Asterisk MGCP

I've searched but can't find an answer as to how many MGCP paths can a single ADIT/CMG card support? It appears it's only 24 ports, maybe 48. What I'd like to do is install 6 Telco T1's into a single (or more) Adit 600 and route inbound calls towards asterisk. Can I have more than one CMG in a single chassis? Or maybe you know of a better way to connect T1's to

Hi, Anybody out there running Adit600s? I have in my care an Adit600 channel bank connected to an old (version 1.0.6) Asterisk instance with MGCP. When trying a more recent Asterisk (1.4.21.2~dfsg-3+lenny1, Stock current Debian) calls fail. I have attempted to add the "slowsequence = yes" line to mgcp.conf. (It seemed to be the only likely candidate in the example files I found

I've been reading the Google searches trying to understand how to tie together Adit 600 to Asterisk to provide 2 way service. I'm about blind from reading. I assume, the answer is using MGCP between the boxes. However, the examples I found don't really explain fully enough to know how to modify examples to work for me. I'll have in the ADIT with T1's. There is a CMG and

Has anyone had any success using the Adit 600 with the CMG card talking MGCP to asterisk? I want to have a central asterisk server with 10 Adit 600's at various locations providing 24 FXS ports.... Thanks, Isaac

I had MCGP working to a ADIT 600 fine with debain sarge stable / asterisk stable - wanted to try red hat and got the below message - then I re-installed debian and am still getting the same message below - any comments are greatly appreciated - I did play with the config files with no prevail - the Adit seems to be doing its job per tech support at CAC. I listed my conigs below I go off hook

Got at suggestion from CarrierAccess to use the Adit 600 as an VoIP router using MGCP IP protocol, instead of controlling it through an E1. Have anyone tried this configuration? How does MGCP works? I've tried to search for it on Google, but I only find the protocol specification for it. Is Asterisk fully capable of this? I can't find any documentatin covering the use of MGCP in Asterisk.

I've finally got my Adit 600 and are configuring it right now. But I have to say, there aren't much documentation for it. I've setup MGCP and Asterisk seems to find it. But all channels (40 FXS channels) are "Down"! But the MGCP itself is "Up" according to the statistics. I can't find any documents how to set each channel to "Up" in the CLI. Any

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Does anyone know what I need to put in the mgcp.conf to connect to an adit 600? Also if you know what I need to configure on the Adit600 itself, that would help too. - --Tod -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.1 (GNU/Linux) Comment: Using GnuPG with Thunderbird - http://enigmail.mozdev.org

FYI, Follow the Quick Start Guide from Carrier Access to setup the CMG (Customer Media Gateway) Router card. Follow the Asterisk mgcp.conf wiki page setup. The only issue I had was with the CAC CMG card, it defaults to strict policy message exchange and dial-tone will not come across when you go off-hook on a FXS port. To resolve this, get back into the CAC CMG configuration, goto: -profile

Has anyone ever gotten an Adit 600 to work with Asterisk1.4 via MGCP. Asterisk keeps giving me the following error in the LOGs: [Jun 30 08:32:59] NOTICE[26785]: chan_mgcp.c:1726 find_subchannel_and_lock: Gateway 10.0.0.245' (and thus its endpoint '*') does not exist MGCP Config: [AFSWestAdit600] host = dynamic context = default canreinvite = no threewaycalling = yes

ONLY ON MONDAY! Well it used to work - calls between my aaln's that is. I moved from debain to redhat (same conf. files for asterisk) and this is what I get.. looks like several errors. errors I never got before. Also asterisk isn't observing the digits as I dial them like it used to however it still trys to route the call when I'm finished dialing. Anyone with a though on this?

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 It seems like Asterisk are having problems detecting DTMF digits when using an Adit 600 channel bank via MGCP. I've tried to turn on RFC 2833 on both Adit and Asterisk, but no digits at all are working then. Anyone experienced simular with Adit or other channel banks? I'm also unable to use V.90 modem through my setup (Adit600 via MGCP -

Can anyone help me with the term that SBC uses to refer to disconnect supervision? I have an Adit 600 channel bank which has helped improve the disconnect detection time down to about 8 seconds. This is still causing some issues in particular with call progress enabled in * we are having a few disconnects while calls are in session (about 2 reported in first 5 days of use). I have talked both to

Hi All, I'm trying to hook up asterisk (CVS-HEAD-02/09/05-13:44:11 ) to a ADIT 600 via MGCP. Got it working really nice but now have a pretty bad problem: 1. When I perform a flash on the telephone, I usually get a second dialtone, but when I dial, dialtone doesn't break. If I flash back and forth a few times, it will eventually give me no dialtone.. here if I dial, it successfully

All: Any have sample config's for an ADIT600 w/ CMG card connected to an Asterisk box via MGCP? Thanks, Garrett Smith <mailto:gsmith@voipsupply.com> gsmith@voipsupply.com VoIPSupply.com -- a division of B2 Technologies, LLC (716) 250-3408 Direct (716) 630-1548 Fax (716) 903-9495 Cell AOL IM: B2sales VoIPSupply.com is North America's largest VAR

I'm emailing this as the customer in this case, since my carrier appears to be completely unable to solve this. A brief rundown of the problem: - We have several voice lines going through the ADIT, of course into a VoIP type of arrangement. - Voice traffic will become choppy, even drop calls completely, at random but quite often. Modem calls (which we needed unfortunately) are a joke. -

I am forklifting a Merridian option 51c with 112 Nortel Digital Handsets and 400 analog units. For the analog units I have quotes for 9 ADIT 600 48 port fxs units and 17 Rhino 24 port FXS channel banks. I have used neither. Which is the best choice? The price difference is not that great. I am looking at Citelinks 24 port Handset Gateway for the Nortel Digital units. (Any other suggestions

Hi All, I just setup an asterisk system equiped to with a 4 FXO port board to interface it with my phone system (Inter-Tel). I realize that I'll be running our of ports once I start showing what can be done with it. My Inter-tel system supports MGCP connectivity to a gateway. Is there any planned development to make chan_mgcp work as a gateway? Another alternative, was to rig * and the

I have an adit 600 with an fxo card connected to a digium T1 card. If I try to make an outgoing call and the T1 cable is disconnected, asterisks returns congested like it should. But, if the adit 600 is connected to the T1 card, the adit 600 immediately "answers" the call even if there are no physical lines attached. I even removed the fxo card and the adit 600 still

Ok, I've pretty much decided to try the Adit route. Somebody who has experience with these tell me if I'm missing something. I have 15 incoming PSTN lines. T1 is not an option at current location. I want to put in an Adit 600 with 2 8-port FXO boards. The adit will then connect to * via a digium t1 board. I configure zaptel.conf for the T1. What other parts would be needed? How do