similar to: Help with IAX Trunk

Hi, do I have a chance to use iax trunking on OpenBSD where there is no zaptel driver or ztdummy available? Do I can use sth. else as timing source? kind regards Sebastian

HI, My Asterisk is registed with my SER. My client are connected to asterisk when they dial any no like 62222 asterisk passes this is ser and then again ser passes this no 2222 (strip 1) back to my asterisk. but insted of ringing this exten it says loop detected. can some one tell me what is wrong. thanks arun -------------- next part -------------- An HTML attachment was scrubbed... URL:

HI I bought 20 license from Digium and install in my server and b'coz of some problem I've to change my server is it possible that I can use those lice and register again in my new server ? Is it possible that I'll be able to use those lice in my old box also ? thanks arun -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi Im trying to install my TC400B trans coder card when I do: modprobe wctc4xxp tail -f /var/log/messages says: May 13 14:56:36 pbx2 kernel: Registered codec translator 'DTE Encoder' with 92 transcoders (srcs=0000000c, dsts=00000101) May 13 14:56:36 pbx2 kernel: Registered codec translator 'DTE Decoder' with 92 transcoders (srcs=00000101, dsts=0000000c) May 13 14:56:36 pbx2

Hi I've configured the queue on my asterisk box and everything is working fine. In my queue I've 3 agents logged in the queue. When call comes they are able to receive the calls without any problem. But some time they are on break and there extension rings and no one is there to answer the call (we don't want them to log off from the queue) but we have one normal user in the same

Hi, In my dial plan I've configured two trunks to make outbound calls (trunk1 and trunk2) to same service provider but I want when any of my exten starts with _2. should goto trunk2 and there should be some kind of disturbance (like some noise or some background noise) when my calls goes to trunk2 to make the call quality bad. Mainly I want to achieve bad call quality on trunk2 by adding

Hi sorry for asking the same question again: here is my details: I've 50 exten in my sip and I'm using snom300 to my asterisk box this asterisk box is connected to another asterisk box using IAX trunk over 1MB full duplex line. I'm using g729 as the preffered codec. Can you please tell me how many calls can go at the same time without causing the any type of problem. thanks arun

Hi, in my dial plan I've configured two trunks to make outbound calls (one for national calls and other international). I want to allow only 2-3 extension to make use of my international trunk to make outbound calls so I want some kind of auth. based on their callerid . Please guide. thanks arun -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, I'm running a php script to generate calls using Asterisk Manager and its working fine. this script call a specified land line number if the phone is answered then It will connect to an extension and play an IVR. But I see in Asterisk CLI its placing the call and it shows channel answered but I don't receive call on my land line and it starts playing the IVR. Please guide me how to

Hi All, I'm just posting this questions to both forums as its related to both. In hope to get some help on below issue: Asterisk 1.4.x CCM = 4.x CME = 4.x codec = g711ulaw Here is my setup: 600X Phones ----> Asterisk ---- SIP Trunk ----> Call Manager -----> CME -----> 461X Phones 461X Phones ----> CME -----> my dial peer points to Asterisk IP for 600X Phones so in

Hi, I've an PRI coming to my asterisk ,calls are coming fine and my agents are able to answer no prob. but I've an agreement with my telco with some incoming no if the no of calls on these no are more then 3 then send to another no. they use busy signal to divert call on another number so I'm sending the call to Congestion() if no of calls in this group are more then 3. But my

I am trying to set up an IAX2 trunk between two servers. Server A has the following in iax.conf: [general] ... [ServerB] type=friend trunk=yes host=dynamic secret=myPassword context=myContext Server B has the following in extensions.conf: [outgoing] exten=>_40X,1,Dial,IAX2/ServerB:myPassword@x.x.x.x/${EXTEN} I am using bmtools to monitor the bandwidth usage, and I am not seeing a difference.

Or perhaps how to configure and refer to two parallel IAX trunks with different codecs? I have a situation where I'm using G.729A as my IAX trunking codec. Now I need to push some short duration, low bitrate modem traffic over the link (a credit card terminal). Obviously the modem audio isn't going to survive the G.729 codec process intact, so for the times the device is used I'd like

I have looked through the archives, and can only find old references to this problem that appear to be no longer relevant, so I thought I'd ask again. I am having a problem with periodic breaks in audio over an IAX trunk. The interruption only happens in one direction, and (I think) only with clients built on the open source libiax. Codec is irrelevant, and jitterbuffer on/off seems to

I have read that an IAX trunk requires a timing device. What wasn't clear to me was whether it is like TDM ie 1 timing device for the trunk, or if each end requires a timing device. I have a zaptel card in one server; do I have to have one in the second server in order to do an IAX trunk? I set up a trunk and so far calls can be made one way, but not the other. It is probably just not

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, I'm attempting to hook up the E400P card to a Siemens ISDN module. I have no knowledge of these Siemens products, so I'm acting on what I've been told about it. The Siemens side is configured to "ISDN30: ECMA QSIG". The Siemens manual states the card provides 30 ISDN B-channels which can be used for trunking or

I understood that a timing device (ztdummy if no zaptel hardware is present) was not necessary anymore with linux kernel 2.6. When I enable iax2 trunking I get this warning chan_iax2.c:8908 build_user: Unable to support trunking on user 'xxxxxx' without zaptel timing The linux kernel is 2.6.22-14-386 Can I ignore this message, and is trunking working despite this warning? The ztdummy

I have 1 * box having x100p installed and the other has no zaptel card at all. both of the * box has compiled in ztdummy module and both have been activated by modprobe ztdummy. When using trunk to connect the 2 *box. The one without zaptel card complaint about unable to accept trunked packet: no matching peer. On the one has zaptel card I have tried to remove the ztdummy module and connect

I have successfully installed and configured the asterisk, the incoming and the outgoing calls are working fine, its a tremendous solution :) Now i want to enable trunking between two asterisk boxes, in the iax.conf i have put: [karachi] ... ... ... trunk=yes ... ... ... everything seems to work fine but when i load asterisk it says: -------------- Feb 17 10:59:14 WARNING[18726]:

starting 161.1-beta3: chan_iax2.c:10925 build_user: Unable to support trunking on user 'iax-out' without DAHDI timing But I have these "timing" modules: ls /usr/lib/asterisk/modules/res_tim* /usr/lib/asterisk/modules/res_timing_dahdi.so /usr/lib/asterisk/modules/res_timing_pthread.so Do I need to do some magic to get these loaded? modules.conf is set to auto. Is this what