similar to: Polycom Firmware

I am having the same issue as below. Has this issue been solved or does anyone know an answer? This error recently began and we have multiple phones out of commission. PLEASE HELP!! http://lists.digium.com/pipermail/asterisk-users/2006-August/162841.html How did you find out about 468*??? It's sure as poop not documented in the Polycom Admin Guide anywhere. -----Original Message-----

Hello everyone, Please forgive the exclamation points but I have been battling this one off and on for about four days now. Sorry for the cross post. It all started with a box of IP 501s. I contacted my reseller and obtained the latest BootRom and SIP firmware. Unzipped, configured, copied over to my FTP server (running AstLinux, of course). The phone booted, so far so good. Updated

Could not find your post for 4 months ago. -------------- Original message -------------- From: "Anton Krall" <akrall-lists@intruder.com.mx> > Yes, check a post that I made about 4 months ago, I posted the cofig for > setting the speaker, handset and ring volumes .. > > |-----Original Message----- > |From: asterisk-users-bounces@lists.digium.com >

I'm setting up a new Asterisk system on a Dell server and I'm getting "fuzzy" voice between the Polycom IP SoundStation 550 and the Asterisk server. I've checked all of my codec settings and both the Asterisk and the Polycom agree on u-Law encoding. I'm using the latest release of the Asterisk code (1.4.17) and other software. If I call between phones (i.e. two

Ever since I upgraded my Polycom 500 to the newest sip.ld (kept the old bootrom), when I dial things like "*98" for voicemail, the screen shows "9*8" and doesn't dial my voicemail system! Is this user error, or errors in the new firmware? Chris Coulthurst chris@shuksan.com -------------- next part -------------- An HTML attachment was scrubbed... URL:

Docs? Polycom has docs? Where would one find this fabled land of... err I mean Polycom does stating what ftp servers are supported? Doug. -----Original Message----- From: Ken D'Ambrosio [mailto:ken@jots.org] Sent: Tuesday, March 07, 2006 12:12 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Cc: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re:

http://downloads.polycom.com/voice/voip/sip_sw_releases_matrix.html Howdy, all. What's the difference between "split" and "combined" firmware, which can be seen at the above link? I've googled to no avail, I'm afraid. Thanks! -Ken -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean.

I am using version 1.4.1.0040 and 2.6.1.0003. I have read about newer versions out there, how can I get them? I'm having an intermittent issue regarding DHCP with one of my phones, and I recall when I loaded 1.4.1 on this one phone, it failed once, then it succeeded the second time. I am wondering if a firmware update will help. Or is there any known issues with Fedora Core 2 dhcpd and IP

Good morning, I have a Polycom 601 with two side cars. I created a list of contacts in XML and it shows up on the side cars exaclty how I set it up in the XXXXXXXXXXXX-directory.xml file (in the order that I wanted it etc.). However when I hit the directories button and then contact directory I see the list in alphabetical order based on the last name. I want it to show up in this list as well in

Is anyone getting '500 Internal Server' errors back from their Polycom phones when Asterisk sends a SIP NOTIFY message to them? I called Polycom tech support, who where utterly useless. Of course Polycom won't officially support it anyway, as they only support Asterisk Business Edition. We're using 1.2.9, but it's been ocurring for quite some time. We have about 35 phones and

Somebody was helpful enough to give me the very latest release of Polycom's firmware (2.1.0). Unfortunately, I still get that issue. So I'm stuck asking again: Anybody ever got that? Mike _____ From: Mike [mailto:list@virtutel.ca] Sent: Wednesday, April 11, 2007 13:37 To: 'Asterisk Users Mailing List - Non-Commercial Discussion' Subject: Polycom 501 issue with latest

I got em. You want em? Anyone know how I can get these to the site listed on the Wiki? Thanks, Wiley -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050512/dfee13b3/attachment.htm

I'm attempting to set up my SoundPoint 501 with my Asterisk server. I've configured DHCP and TFTP and successfully updated both the BootRom and SIP application. I've also created a custom cfg file for this phone's MAC address and the settings seem to be taking just fine. I can see that the phone registers with my Asterisk server but 'sip show peers' reports that the phone

Hi, I am currently playing with DD-WRT and I like it. I am looking for something that is more "SIP Aware". Anyone know one those that are out there ? Thanks. Dovid -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20071126/eb28ce44/attachment.htm

Hi, I've upgraded a few Polycom 501 to SIP 2.0.3b (can't get 2.1.0 because of Polycom's firmware policy, but this is the "latest publicly available" from Polycom's web site). I've noticed that some keys get "sticky" though. Soft buttons for example (i.e. "end call") need to be pressed 2-3 times for them to react. I've downgraded to

I have a couple of Polycom phones, bootrom 2.5.0, SIP 1.3.1.0056. Works great with Asterisk when I power on the phone. However, after some time, say an hour, I cannot receive calls on this phone. On Asterisk, when I do "database show", it does show the phone in there, but it cannot reach the phone. Is there a way to keep alive the connection with Polycom? Any suggestions? Thanks, --

I was progressively upgrading this phone from 3.1.2 to 3.2.3, then to 4.0.0. v3.2.3 worked fine, but when I went to 4.0.0 (Even adding the more specific 2345-11500-040.bootrom.ld), it won't run, and just keeps rebooting. Now I've got a really nice doorstop unless someone knows how to get out of this predicament. Help! 0925003705|cfg |3|00|Beginning to provision phone 0925003705|dns

I'm having problems updating my bootrom to the latest (3.2.2) version. Basically, my phone starts downloading the bootrom, but I am completely certain that it doesn't actually complete the process. It gives me an "error updating bootROM!" message, but it only takes about 2 seconds to complete the download (which, because of my WAN link and FTP server environnement I know is

I have a question about DHCP and boot server supporting more than 1 model of Polycom phones. According to Polycom "standards", Polycom phone boots up to get a DHCP address and at the same time getting a boot server string (with username and password) to logon to boot server to download SIP, bootROM and etc. That is okay if there is only one type of phone (that requires a specific SIP

i recently bought an SP4000 conference phone but having problem provisioning it using ftp, every time it just hangs at "Updating initial configuration..." screen. when i switch it to tftp, it'll work fine. i though it was bootrom/firmware issue so i upgrade it to bootrom 3.2.2/sip 2.0.1 but it makes no difference. any thoughts? p.s. i'm using debian sarge proftpd 1.2.10 and the