similar to: no lights on TE405P, but shows up in lspci, modules loaded

I am trying to install a TE405P which is to be connected to E1 trunks. I have set the jumpers to E1 (closed), but modprobe wct4xxp still fails with the message: ZT_CHANCONFIG failed for channel 97 - which obviously means the card is still in T1 mode. I have tried everything I can think of, any ideas? TIA

Hi, I am new with asterisk. I am setting a Wildcard TE405P. E1s in Italy come in on a pair of RG-59 coax cables with BNC connectors. So I need an adapter/balun http://www.allcomtlc.com/al_g703n3.htm . I have It but I am not sure that It works. I have configured my asterisk in this way: zaptel.conf span=1,1,0,ccs,hdb3,crc4 dchan=16 bchan=1-15,17-31 loadzone=it defaultzone=it zapata.conf

Forget the sound card. It isn't related. The subject above should have read 'TE405P No Voice Problem' or something similar. It appears to be a zaptel timing issue, but I have found a workaround. For those of you just tuning in, here is the story: I have a CentOS/Intel 865 box currently running Asterisk 1.2.7.1 and zap 1.2.5, both compiled from the source available off the main

Greetings, According to the FAQ "When you load the module and have no circuit/channel bank the LED's should flash red" I get the "knight rider" lights before the module loads, but after the modules are loaded I don't get any lights, other equipment plugged in or not. The card has been on my shelf a while so I wonder if it needs a firmware upgrade ? Can the cards

Hi, i am running * 1.0.9 with a newer version of the TE405P. Modprobe wct4xxp and ztcfg are OK. zap show channels only shows me the following. my zapata.conf: [pstn] switchtype=euroisdn pridialplan=unknown prilocaldialplan=unknown usecallingpres=yes busydetect=no ; not need on pri callprogress=no ; was yes but wiki says experimatley could be produce hangups callwaitingcallerid=yes ; show

Dear All I installed a Digium card TE405P with zaptel and its running successfully with no alarms, but asterisk is not running . Any one have a cure or advice 03:09.0 Communication controller: Digium, Inc. Wildcard TE405P quad-span T1/E1/J1 card 5.0V (rev 02) Nov 14 07:56:58 localhost kernel: wct4xxp: Clearing yellow alarm on span 2 Nov 14 07:56:58 localhost kernel: wct4xxp: Clearing

Hello, I'm running Fedora Core 3 with udev, and asterisk/zaptel/libpri from cvs. I have followed the README.udev instructions replacing insmod with modprobe and rmmod with modprobe -r and adding the 60-zaptel.rules file, yet no matter what I do I still get this error on boot(or when I run service zaptel restart): [root@pbx ~]# /etc/init.d/zaptel restart Unloading zaptel hardware drivers:

Folks, I'm experimenting with bringing multiple (8) analog lines from our local telco into a Carrier Access ADIT 600 channel bank with an FXO module, then having this talk to Asterisk via the T1 TDM controller on the ADIT and a TE405P card. I don't know if this will work well (ie: give me decent echo cancellation, call disconnect supervision, caller ID etc) but I haven't had much

Hi to all, I have a problem with this wildcard and one E1 line. The server is a Asus P4P800S with the 865PE chipset, and 512MB RAM. The kernel version is 2.4.26. I have donwload and build the latest CVS version of zaptel, libpri and asterisk following the ufficial instructions of digium. I have set up my server in this way: zaptel.conf loadzone=it defaultzone=it

Hi all, i am stuck with the configuration of asterisk - modules are loaded ( zaptel and wct4xxp ) - i have zaptel.conf configure, output of ztcfg -vv --- snip -- rapid:~# ztcfg -vv Zaptel Configuration ====================== SPAN 1: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 2: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 3: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet

My Asterisk server believes that a Digium TE405P and sound are incompatible. Basically, no matter what else I do to the machine it terms of hardware, if the TE405P is installed, none of the playback/background/etc commands work. MOH works fine. So far, I have tried: 1) Seven different PCI soundcards with different chipsets. (Go go Computer Junk Store!) 2) Disabling each and every device

lspci dont show Digium card. The motherboard is Intel 945gnt. 00:00.0 Host bridge: Intel Corporation 945G/P Memory Controller Hub (rev 02) 00:02.0 Display controller: Intel Corporation 945G Integrated Graphics Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01) 00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 (rev

I'm installing my new TE411P's but found in my new system, /dev/zap/channel is missing. Anyone know off hand what actually creates that file? Modprobe didn't complain when I loaded zaptel and wct4xxp modules. Ztcfg complains too: > ztcfg Notice: Configuration file is /etc/zaptel.conf line 0: Unable to open master device '/dev/zap/ctl' 1 error(s) detected Using cvs-head

Hi, I'm cutting my teeth setting up a home asterisk server, but having some trouble getting Zaptel to recognize a X100P clone PCI (Motorola SM56 which should work according to various wiki's). What struck me was that the "/proc/interrupts" do not include IRQ 11 as the "lpcpi -v" is reporting. Am I missing something fundamental here? Any hint is greatly

I successfully installed asterisk@home 0.6, but when i try to load the wct4xxp module for the TE405P I just got, I get the following: Found TE410P at base address fb7ffc00, remapped to e0220c00 TE410P version c01a009b Tried to load 1c8ac800 into 00000000, but got 188ac800 instead Tried to load 1c8ac000 into 00000001, but got 188ac000 instead Tried to load 07fc07fc into 00000002, but got 03fc07fc

hi i'm trying to configure a TE205P on asterisk@home i've edited /etc/sysconfig/zaptel adding this line: MODULES="$MODULES wct2xxp" now, when the system is loading, i can see that the wct2xxp module is loaded correctly but if i try the command: /usr/local/sbin/genzaptelconf i get: STOPPING ASTERISK STOPPING FOP SERVER Generating '/etc/zaptel.conf' Generating

Hi anyone have a idea for debug my digium TE405P card ? My zaptel.conf: span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone = fr defaultzone = fr My Zapata.conf: [channels] language=fr context=from-E1 switchtype = euroisdn pridialplan = unknown signalling = pri_cpe usecallerid=yes hidecallerid=no callwaiting=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes

Hello! I have problems compiling zaptel (tried 1.2.11, 1.2.10 and 1.4.0-beta2 -- all give the same error) with 2.6.19 kernel CC [M] /home/roman/install/asterisk/zaptel-1.4.0-beta2/xpp/card_fxo.o In file included from /home/roman/install/asterisk/zaptel-1.4.0-beta2/xpp/xpd.h:26, from /home/roman/install/asterisk/zaptel-1.4.0-beta2/xpp/card_fxo.c:28:

I'm installing TE405P card. This is my zaptel.conf. -------------------------------------- span=1,0,0,ccs,hdb3,crc4 span=2,1,0,ccs,hdb3,crc4 span=3,0,0,ccs,hdb3,crc4 span=4,0,0,ccs,hdb3,crc4 loadzone = us defaultzone= us -------------------------------------- When i modprobe wct4xxp, -------------------------------------- PCI: Found IRQ 11 for device 02:0b.0 PCI: Sharing IRQ 11 with

I go to my Zaptel 1.4.0 folder and run ./configure; make linux26; make install and I don't see any errors. This is out of my modprobe.conf: install tor2 /sbin/modprobe --ignore-install tor2 && /sbin/ztcfg install torisa /sbin/modprobe --ignore-install torisa && /sbin/ztcfg install wcusb /sbin/modprobe --ignore-install wcusb && /sbin/ztcfg install wcfxo