similar to: Problem with FXS ports of TDM400P

I am in the process of buying a TDM800 card from Yeastar ( http://www.yeastar.com/products.asp?TypeName=TDM800%20PCI%20Card&cTypeName=1 ) Any one has tested this cards? How reliable are them? I am specially interested in the FXO/FXS module. -- Gustavo Felisberto (HumpBack) Web: http://dev.gentoo.org/~humpback Blog: http://blog.felisberto.net/ ------------ It's most certainly GNU/Linux,

I have a costumer with a Siemens PBX installed, and I would like to setup a Asterisk system that would act as a kind of Proxy between the Siemens PBX and the operator network. The current setup is: Siemens PBX 2*PRI <-> Operator what I want is: Siemens PBX 2*PRI <-> Asterisk BOX <-> Operator For the Siemens PBX the Asterisk Box would be a standard Telephony Operator, and the

I have a TDM-400 from digium with 2FXO+2FXS ports. Any idea on how much power will this drain from the 12 and 5 V connector when all ports are in use? -- Gustavo Felisberto (HumpBack) Web: http://dev.gentoo.org/~humpback Blog: http://blog.felisberto.net/ ------------ It's most certainly GNU/Linux, not Linux. Read more at http://www.gnu.org/gnu/why-gnu-linux.html . -------------

I'm using asterisk 1.2.14 When asterisk stores voicemail messages in /var/spool/asterisk/voicemail/default/EXTENSION/INBOX files are created with: -rwx------ 1 asterisk web-aster 6690 Apr 17 16:08 msg0002.WAV -rwx------ 1 asterisk web-aster 6732 Apr 17 16:08 msg0002.gsm -rw------- 1 asterisk web-aster 274 Apr 17 16:08 msg0002.txt -rwx------ 1 asterisk web-aster 65324 Apr 17 16:08

I think I have a bad FXS module on my TDM400P. Channel map: >> >> Channel 01: FXO Kewlstart (Default) (Slaves: 01) >> Channel 02: FXS Kewlstart (Default) (Slaves: 02) >> >> 2 channels configured. >> ZT_CHANCONFIG failed on channel 1: No such device or address (6) The zaptel loads ok, but the wctdm reports No such device or address and stays loaded. The

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

I've got the latest zaptel and cvs asterisk software loaded on my phone server running FC3. And yes, It's fully updated and udev is setup correctly. I've got a TDM400P with one FXS and one FXO module installed. When I load zaptel and wctdm and run ztcfg -vvv, I get this: [root@asterisk ~]# ztcfg -vvv ZT_CHANCONFIG failed on channel 1: No such device or address (6) Zaptel

Hi all, I bought a Sangoma A200 card from an online supplier and explained exactly what I wanted, 3 incoming phone lines to PBX and a life line (some where to connect a standard BT phone to the PBX incase the power goes, making the BT phone ring). I was told to order 1 x FXS module (2 FXS ports) 2 x FXO modules (4 FXO ports) However being a complete noob, I have connected the 3 lines to the

Hi , I have an asterix (1.2.7.1) box with 3 TDM400P and 10 FXO modules, and zaptel (1.2.5). The problem is that 6 modules can't be initaized and i get the folowing error: May 7 09:17:37 WARNING[7739] chan_zap.c: Unable to specify channel 9: No such device May 7 09:17:37 ERROR[7739] chan_zap.c: Unable to open channel 9: No such device here = 0, tmp->channel = 9, channel = 9 ztcfg output

Hello, everyone After having spent several time to look for any solution for my problem, I decided to write here. Here is the problem got a Digium X101 FXO card and Digium TDM400P alias freshmaker (1 fxs module on it on first port ) in my asterisk box. The X101 works perfectly. The problem comes from the TDM400, when i plug a tested working phone on it , i get no dialtone; the goal is to

This has got to be a stupid error I'm making... I have been experimenting with different hardware and software configurations before I decide what to use as a production platform. Up until just recently things were going well. But now it appears I'm unable to get access to my TDM400p from Asterisk. I know the TDM card works fine, used it in another machine where it performed flawlessly.

Hi, I just got my TDM400P card (2 modules) and i installed it no probs. The card is detected fine, but for some reason when I add the card to zaptel.conf i get the following error: --snip-- ZT_CHANCONFIG failed on channel 2: Invalid argument (22) Did you forget that FXS interfaces are configured with FXO signalling and that FXO interfaces use FXS signalling? --snip-- My /etc/zaptel.conf looks

Hi when I turn on my PC I able to load the drivers and start my card, if I reboot the PC I have the following error ztcfg -vvv Zaptel Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) Channel 03: FXS Kewlstart (Default) (Slaves: 03) Channel 04: FXS Kewlstart (Default) (Slaves: 04) 4 channels

Hi I have been having a rough time getting a Sangoma A200/Remora FXO/ FXS Analog AFT card set up properly. The main issue is that the card has four ports and as far as I can tell Asterisk is only seeing two. On the two that it recognizes the "Green" FXS ports are not green, they just are not lit. The "RED" FXO ports are indeed red, but from what I have read your not

I have a TMD400 card installed in a PC with one fxs (installed in slot 2) and two fxos (installed in slots 3 & 4).? fxos work fine but I am unable to get a dial tone for any devices connected to the fxs.? I have correctly connected the power supply to the card and I have even tried moving the card from slot 1 to 2 on the board. Below is from the console when I try to route a call from FXO on

Hello. Well I finally rx'd my dev kit (new batch of TDM's apparently. I'm on Mandrake 9.1 There were no hardware install instructions, it would have been nice to know whether the 4-way power connector was to be used or was for some other future or expansion purpose. It came with a floppy disc, no label and it wasn't even write protected. The only readme file was

As best i could figure it out, I've installed dahdi and rc4. My TDM400P doesn't answer fxo or fxs. /etc/dahdi/system.conf: loadzone = us defaultzone=us fxoks=1,2 fxsks=4 /etc/asterisk/chan_dahdi.conf: [house-phones] context=internal ; Uses the [internal] context in extensions.conf signalling=fxo_ks ; fxo_ks Use FXO signalling for an FXS chanel dahdichan => 1 ;

Hi All, Which is the best signalling to use when connecting an FXS inteface on a TDM400 to a standard telephone. I see that all examples use fxo_ks, but it is my understanding that kewl start is really designed for connections to the CO so that hangup etc. can be detected. So does it make any sense to configure a telephone for fxo_ks? Or should it be configured for fxo_ls? Regards Garry Taylor

I installed the TDM400P and installed it on a system running on Fedora Core1, please refer to the steps below. I connected an analogue phone to the FXS port. When I pick up the speaker I don't hear the dialtone although when I press a number key I hear a DTMF generated. What could be the problem? I appreciate your help 1- First I installed the TDM400P in the PCI slot and connected

(I'm producing a writeup on all the things one run into building an * box. Which after a couple of boxes is showing up aplenty.) So this uses the working h/w and config's from another box. All I do is build in a new computer. Loading the modules I got: __________________________________________________ Zaptel Configuration ====================== Channel map: Channel 01: FXS