This has got to be a stupid error I'm making...
I have been experimenting with different hardware and software
configurations before I decide what to use as a production platform. Up
until just recently things were going well.
But now it appears I'm unable to get access to my TDM400p from Asterisk. I
know the TDM card works fine, used it in another machine where it
performed flawlessly. I have been using the same set of conf files, just
copying them over from machine to machine. The hardware is Pentium 4
all-Intel chipset mainboard.
The one difference here is I'm trying CentOS. I've been through the
problems getting Zaptel to compile with the error in spinlock.h. I got
to...
Zaptel Configuration
=====================
Channel map:
Channel 01: FXO Kewlstart (Default) (Slaves: 01)
Channel 02: FXS Kewlstart (Default) (Slaves: 02)
Channel 03: FXS Kewlstart (Default) (Slaves: 03)
Channel 04: FXS Kewlstart (Default) (Slaves: 04)
4 channels configured.
and thought I was home free. Wrong!
zttool recognizes the card properly and reports status "OK"
Asterisk runs and I can make calls on SIP phones with no problems. However
I get no dial tone on the analog phone and outgoing calls through the TDM
(from the SIP phones of course!) produce this on the console:
NOTICE[5934]: app_dial.c:1010 dial_exec_full: Unable to create channel of
type 'Zap' (cause 66 - Channel not implemented)
== Everyone is busy/congested at this time (1:0/0/1)
-- Executing Congestion("SIP/100-24d1", "") in new stack
== Spawn extension (internal, 91234567, 102) exited non-zero on
'SIP/100-24d1'
The conf files are the same as they were on another working machine, I
just copied them over. I'll be going over them /again/ next.
What am I missing?
Thanks.
-Ben
couple of things... was asterisk compiled after zaptel? from the cli try "load chan_zap.so" and see what you get Ben Gore wrote:> This has got to be a stupid error I'm making... > > I have been experimenting with different hardware and software > configurations before I decide what to use as a production platform. Up > until just recently things were going well. > > But now it appears I'm unable to get access to my TDM400p from Asterisk. I > know the TDM card works fine, used it in another machine where it > performed flawlessly. I have been using the same set of conf files, just > copying them over from machine to machine. The hardware is Pentium 4 > all-Intel chipset mainboard. > > The one difference here is I'm trying CentOS. I've been through the > problems getting Zaptel to compile with the error in spinlock.h. I got > to... > > Zaptel Configuration > =====================> > > Channel map: > > Channel 01: FXO Kewlstart (Default) (Slaves: 01) > Channel 02: FXS Kewlstart (Default) (Slaves: 02) > Channel 03: FXS Kewlstart (Default) (Slaves: 03) > Channel 04: FXS Kewlstart (Default) (Slaves: 04) > > 4 channels configured. > > and thought I was home free. Wrong! > > zttool recognizes the card properly and reports status "OK" > > Asterisk runs and I can make calls on SIP phones with no problems. However > I get no dial tone on the analog phone and outgoing calls through the TDM > (from the SIP phones of course!) produce this on the console: > > NOTICE[5934]: app_dial.c:1010 dial_exec_full: Unable to create channel of > type 'Zap' (cause 66 - Channel not implemented) > == Everyone is busy/congested at this time (1:0/0/1) > -- Executing Congestion("SIP/100-24d1", "") in new stack > == Spawn extension (internal, 91234567, 102) exited non-zero on > 'SIP/100-24d1' > > The conf files are the same as they were on another working machine, I > just copied them over. I'll be going over them /again/ next. > > What am I missing? > > Thanks. > > -Ben > > > > > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > Asterisk-Users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users >
Hello again.. Disregard my last message. I recompiled Asterisk and all is well. I guess all the messing around with trying to get Zaptel to compile correctly screwed something up with the Asterisk configuration. Thanks. -Ben Original message:>This has got to be a stupid error I'm making... > >I have been experimenting with different hardware and software >configurations before I decide what to use as a production platform. Up >until just recently things were going well. > >But now it appears I'm unable to get access to my TDM400p from Asterisk. I >know the TDM card works fine, used it in another machine where it >performed flawlessly. I have been using the same set of conf files, just >copying them over from machine to machine. The hardware is Pentium 4 >all-Intel chipset mainboard. > >The one difference here is I'm trying CentOS. I've been through the >problems getting Zaptel to compile with the error in spinlock.h. I got >to... > >Zaptel Configuration >=====================> > >Channel map: > >Channel 01: FXO Kewlstart (Default) (Slaves: 01) >Channel 02: FXS Kewlstart (Default) (Slaves: 02) >Channel 03: FXS Kewlstart (Default) (Slaves: 03) >Channel 04: FXS Kewlstart (Default) (Slaves: 04) > >4 channels configured. > >and thought I was home free. Wrong! > >zttool recognizes the card properly and reports status "OK" > >Asterisk runs and I can make calls on SIP phones with no problems. However >I get no dial tone on the analog phone and outgoing calls through the TDM >(from the SIP phones of course!) produce this on the console: > >NOTICE[5934]: app_dial.c:1010 dial_exec_full: Unable to create channel of >type 'Zap' (cause 66 - Channel not implemented) > == Everyone is busy/congested at this time (1:0/0/1) > -- Executing Congestion("SIP/100-24d1", "") in new stack > == Spawn extension (internal, 91234567, 102) exited non-zero on >'SIP/100-24d1' > >The conf files are the same as they were on another working machine, I >just copied them over. I'll be going over them /again/ next. > >What am I missing?