Ketema Harris
2009-Feb-24 20:41 UTC
[asterisk-users] Configuring chan_dahdi.conf for Sangoma A200/Remora FXO/FXS Analog AFT card
Hi I have been having a rough time getting a Sangoma A200/Remora FXO/
FXS Analog AFT card set up properly.
The main issue is that the card has four ports and as far as I can
tell Asterisk is only seeing two. On the two that it recognizes the
"Green" FXS ports are not green, they just are not lit. The
"RED" FXO
ports are indeed red, but from what I have read your not supposed to
plug the analog phone into those. So from my standpoint its not
"working" below is some more info about my system. Any help would be
appreciated.
I am running the following:
http://wiki.sangoma.com/sangoma-hardware#A200
Asterisk 1.6.0.5
dahdi-linux-2.1.0.4
dahdi-tools-2.1.0.2
wanpipe-3.3.15.20
linux kernel 2.6.27
The card is detected, but I can only get two channels configured.
Here is my chan_dahdi.conf
[trunkgroups]
[channels]
context=default
usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
canpark=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=yes
relaxdtmf=yes
rxgain=0.0
txgain=0.0
group=1
callgroup=1
pickupgroup=1
immediate=no
progzone=us
tonezone=0
jbenable=yes
;Sangoma AFT-A200 [slot:4 bus:5 span:1] <wanpipe1>
context=default
group=0
echocancel=yes
signalling=fxs_ks
channel => 1
context=default
group=0
echocancel=yes
signalling=fxs_ks
channel => 2
dahdi show version
DAHDI Version: 2.1.0.4 Echo Canceller: MG2
dahdi show status
Description Alarms IRQ bpviol CRC4
Fra Codi Options LBO
wrtdm Board 1 OK 0 0 0
CAS Unk YEL 0 db (CSU)/0-133 feet (DSX-1)
dahdi show channels
Chan Extension Context Language MOH Interpret
Blocked State
pseudo from-zaptel
default In Service
1 default
default In Service
2 default
default In Service
Whenever asterisk starts or chan_dahdi.so is reloaded I get the
following:
[Feb 24 15:23:41] WARNING[10206]: chan_dahdi.c:14304 process_dahdi:
Ignoring signalling at line 38.
-- Reconfigured channel 1, FXS Kewlstart signalling
[Feb 24 15:23:41] WARNING[10206]: chan_dahdi.c:14304 process_dahdi:
Ignoring signalling at line 44.
-- Reconfigured channel 2, FXS Kewlstart signalling
My goal is:
1) Get Dialtone for my analog phone.
2) Be able to send and make calls from my analog phone
3) Be able to receive and send faxes from my fax machine
My service provider is VOIP, so I will never be getting or sending
calls from/to the traditional telco. But I do believe I should be
able to send and receive calls from this device out to my SIP provider.
Ketema Harris
2009-Feb-24 20:55 UTC
[asterisk-users] Configuring chan_dahdi.conf for Sangoma A200/Remora FXO/FXS Analog AFT card
I forgot to add that I have tried changing the chan_dahdi.conf file by
adding:
context=default
group=1
echocancel=yes
signalling=fxo_ks
channel => 3
context=default
group=1
echocancel=yes
signalling=fxo_ks
channel => 4
This addition simply caused dahdi not to load at all:
[Feb 24 15:54:52] WARNING[11026]: chan_dahdi.c:14304 process_dahdi:
Ignoring signalling at line 38.
-- Reconfigured channel 1, FXS Kewlstart signalling
[Feb 24 15:54:52] WARNING[11026]: chan_dahdi.c:14304 process_dahdi:
Ignoring signalling at line 44.
-- Reconfigured channel 2, FXS Kewlstart signalling
[Feb 24 15:54:52] WARNING[11026]: chan_dahdi.c:14304 process_dahdi:
Ignoring signalling at line 50.
[Feb 24 15:54:52] ERROR[11026]: chan_dahdi.c:13459 build_channels:
Unable to reconfigure channel '3'
[Feb 24 15:54:52] WARNING[11026]: chan_dahdi.c:14667 reload: Reload of
chan_dahdi.so is unsuccessful!
On Feb 24, 2009, at 3:41 PM, Ketema Harris wrote:
> Hi I have been having a rough time getting a Sangoma A200/Remora FXO/
> FXS Analog AFT card set up properly.
>
> The main issue is that the card has four ports and as far as I can
> tell Asterisk is only seeing two. On the two that it recognizes the
> "Green" FXS ports are not green, they just are not lit. The
"RED" FXO
> ports are indeed red, but from what I have read your not supposed to
> plug the analog phone into those. So from my standpoint its not
> "working" below is some more info about my system. Any help
would be
> appreciated.
>
> I am running the following:
>
> http://wiki.sangoma.com/sangoma-hardware#A200
>
> Asterisk 1.6.0.5
> dahdi-linux-2.1.0.4
> dahdi-tools-2.1.0.2
> wanpipe-3.3.15.20
> linux kernel 2.6.27
>
> The card is detected, but I can only get two channels configured.
> Here is my chan_dahdi.conf
>
> [trunkgroups]
>
> [channels]
> context=default
> usecallerid=yes
> hidecallerid=no
> callwaiting=yes
> usecallingpres=yes
> callwaitingcallerid=yes
> threewaycalling=yes
> transfer=yes
> canpark=yes
> cancallforward=yes
> callreturn=yes
> echocancel=yes
> echocancelwhenbridged=yes
> relaxdtmf=yes
> rxgain=0.0
> txgain=0.0
> group=1
> callgroup=1
> pickupgroup=1
> immediate=no
> progzone=us
> tonezone=0
> jbenable=yes
>
> ;Sangoma AFT-A200 [slot:4 bus:5 span:1] <wanpipe1>
> context=default
> group=0
> echocancel=yes
> signalling=fxs_ks
> channel => 1
>
> context=default
> group=0
> echocancel=yes
> signalling=fxs_ks
> channel => 2
>
> dahdi show version
> DAHDI Version: 2.1.0.4 Echo Canceller: MG2
>
> dahdi show status
> Description Alarms IRQ bpviol CRC4
> Fra Codi Options LBO
> wrtdm Board 1 OK 0 0 0
> CAS Unk YEL 0 db (CSU)/0-133 feet (DSX-1)
>
> dahdi show channels
> Chan Extension Context Language MOH Interpret
> Blocked State
> pseudo from-zaptel
> default In Service
> 1 default
> default In Service
> 2 default
> default In Service
>
> Whenever asterisk starts or chan_dahdi.so is reloaded I get the
> following:
>
> [Feb 24 15:23:41] WARNING[10206]: chan_dahdi.c:14304 process_dahdi:
> Ignoring signalling at line 38.
> -- Reconfigured channel 1, FXS Kewlstart signalling
> [Feb 24 15:23:41] WARNING[10206]: chan_dahdi.c:14304 process_dahdi:
> Ignoring signalling at line 44.
> -- Reconfigured channel 2, FXS Kewlstart signalling
>
> My goal is:
>
> 1) Get Dialtone for my analog phone.
> 2) Be able to send and make calls from my analog phone
> 3) Be able to receive and send faxes from my fax machine
>
> My service provider is VOIP, so I will never be getting or sending
> calls from/to the traditional telco. But I do believe I should be
> able to send and receive calls from this device out to my SIP
> provider.
>
> _______________________________________________
> -- Bandwidth and Colocation Provided by http://www.api-digital.com --
>
> asterisk-users mailing list
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-users
John Novack
2009-Feb-24 21:27 UTC
[asterisk-users] Configuring chan_dahdi.conf for Sangoma A200/Remora FXO/FXS Analog AFT card
What does Sangoma have to say? They have, in the past, given excellent support and their cards have a 5 year warranty. Best try there first. John Novack Ketema Harris wrote:> Hi I have been having a rough time getting a Sangoma A200/Remora FXO/ > FXS Analog AFT card set up properly. > > The main issue is that the card has four ports and as far as I can > tell Asterisk is only seeing two. On the two that it recognizes the > "Green" FXS ports are not green, they just are not lit. The "RED" FXO > ports are indeed red, but from what I have read your not supposed to > plug the analog phone into those. So from my standpoint its not > "working" below is some more info about my system. Any help would be > appreciated. > > I am running the following: > > http://wiki.sangoma.com/sangoma-hardware#A200 > > Asterisk 1.6.0.5 > dahdi-linux-2.1.0.4 > dahdi-tools-2.1.0.2 > wanpipe-3.3.15.20 > linux kernel 2.6.27 > > The card is detected, but I can only get two channels configured. > Here is my chan_dahdi.conf > > [trunkgroups] > > [channels] > context=default > usecallerid=yes > hidecallerid=no > callwaiting=yes > usecallingpres=yes > callwaitingcallerid=yes > threewaycalling=yes > transfer=yes > canpark=yes > cancallforward=yes > callreturn=yes > echocancel=yes > echocancelwhenbridged=yes > relaxdtmf=yes > rxgain=0.0 > txgain=0.0 > group=1 > callgroup=1 > pickupgroup=1 > immediate=no > progzone=us > tonezone=0 > jbenable=yes > > ;Sangoma AFT-A200 [slot:4 bus:5 span:1] <wanpipe1> > context=default > group=0 > echocancel=yes > signalling=fxs_ks > channel => 1 > > context=default > group=0 > echocancel=yes > signalling=fxs_ks > channel => 2 > > dahdi show version > DAHDI Version: 2.1.0.4 Echo Canceller: MG2 > > dahdi show status > Description Alarms IRQ bpviol CRC4 > Fra Codi Options LBO > wrtdm Board 1 OK 0 0 0 > CAS Unk YEL 0 db (CSU)/0-133 feet (DSX-1) > > dahdi show channels > Chan Extension Context Language MOH Interpret > Blocked State > pseudo from-zaptel > default In Service > 1 default > default In Service > 2 default > default In Service > > Whenever asterisk starts or chan_dahdi.so is reloaded I get the > following: > > [Feb 24 15:23:41] WARNING[10206]: chan_dahdi.c:14304 process_dahdi: > Ignoring signalling at line 38. > -- Reconfigured channel 1, FXS Kewlstart signalling > [Feb 24 15:23:41] WARNING[10206]: chan_dahdi.c:14304 process_dahdi: > Ignoring signalling at line 44. > -- Reconfigured channel 2, FXS Kewlstart signalling > > My goal is: > > 1) Get Dialtone for my analog phone. > 2) Be able to send and make calls from my analog phone > 3) Be able to receive and send faxes from my fax machine > > My service provider is VOIP, so I will never be getting or sending > calls from/to the traditional telco. But I do believe I should be > able to send and receive calls from this device out to my SIP provider. > > _______________________________________________ > -- Bandwidth and Colocation Provided by http://www.api-digital.com -- > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > >-- Dog is my co-pilot -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20090224/ed6f2561/attachment.htm