similar to: Echo Cancelling VoIP traffic

Hi List, Yesterday night after a power off due to a faulty UPS my asterisk doesn't want to start anymore. Here is what I get on the CLI: Asterisk Ready. *CLI> Disconnected from Asterisk server: Bad file descriptor. Executing last minute cleanups == Destroying musiconhold processes Asterisk uncleanly ending (0). I use 1.2.7 I think on a debian sarge and cdr_pgsql too. Any ideas?

You can even set it to zero. Mine works well when in zero. The line pick up immediately :> -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Chris Stenton Sent: Thursday, February 09, 2006 6:57 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] SPA-3000 VOIP-PSTN

Hi List, Is there a way to tell asterisk to only accept SIP streams from the same IP address that is used for signaling? Thanks, Jean-Michel. -- Jean-Michel Hiver - http://ykoz.net/ D?couvrez la R?union des Technologies IP & Telecom TEL: +262 (0)262 55 03 98 - RCS 434 273 330 SAINT PIERRE

Hi List, I was wondering if anybody had tried running Asterisk inside virtualization software such as Xen. Are there known problems doing it? Cheers, Jean-Michel. -- Jean-Michel Hiver - http://ykoz.net/ D?couvrez la R?union des Technologies IP & Telecom TEL: +262 (0)262 55 03 98 - RCS 434 273 330 SAINT PIERRE

Hi List, Being very new to Xen I have a few generic questions for the list, I hope to grab some useful advice and pointers to documentation. I am evaluating Xen to consolidate a few existing servers into one appliance (mainly in order to reduce power consumption, heat, and hardware failure risks). I plan to have a SER router, an Asterisk LCR router, a voicemail server, a calling card server

Hi, I'd like to use the convenience of apt packaging, but debian sarge's default asterisk is something like 1.0.7. Are there any apt repositories which provide newer versions of the software? Thanks! -- Jean-Michel Hiver - http://ykoz.net/ D?couvrez la R?union des Technologies IP & Telecom TEL: +262 (0)262 55 03 98 - RCS 434 273 330 SAINT PIERRE

Hi List, Do you know if there are any plans to improve i18n for Asterisk? The current i18n way of doing it with asterisk is very limited and most of the time does not work. For example, take voicemail: "message" "received" "at" "seven" "30" "am" might sound good in English. But: "message" "recu" "a"

Hi List, In one of my AGIs (using DeadAGI) I grab the answered time using: my $res = $agi->exec ("DIAL $dialstring"); my $answeredtime = $agi->get_variable ("ANSWEREDTIME"); However this information differs from what's written in the Master.csv file (which happens to be the correct value!) Any ideas why? I'm using asterisk 1.2.7.1 and the

Around 1978, when I was consulting to a multinational company in the business of agriculture, I witnessed this configuration in their communications center in NYC: A paper tape punch attached to a teletype machine was busily punching out a tape that was being spewed into a wastebasket. Somehow, running behind it by several feet of tape, was a paper tape reader on another teletype drawing

IMHO! I just see a skype channel as something good for asterisk. Skype has broad coverage. I can't imagine that skype wouldn't be interested in selling corporate accounts "skype trunk lines". Imagine having unlimited or X amount of continious calls coming in on SkypeIN and out on SkypeOUT from Asterisk. Internal Phones would all talk IAX or SIP to asterisk and use all PBX

Hi List, I am working on least cost routing code on the moment, and I am stumbling on a problem. Say you have provider A having: Prefix XXX 0.10 Prefix XXXYYY 0.20 And provider B having Prefix XXX 0.15 You're stuck, because you cannot decide if provider B's "XXX" prefix also covers XXXYYY numbers or not. If it doesn't, it would be a waste

Hi List, I am looking for a 1 FXO analog termination device, other than the obvious PC + FXO card, and which can achieve decent call quality. The SPA-3000 seems an option... have you got any other ideas? Cheers, Jean-Michel.

Hello, Just want to tap the collective wisdom of this list as to experiences pertaining to the Handytone HT488 and the Sipura SPA-3000 adapters... Basically I'm looking for a FXO/FXS/LAN ATA and these two seems to be the top of the pick..Any comments and experiences esp. with Asterisk compatibility would be great, before I plonk in the bucks. TIA. /wai-sun

Hi List, After quite a bit of struggle, it looks like I'm all ready to roll out prepaid cards on my small island. I now have a 4 E1s with a bit of spare capacity in order to accept incoming calls, and I can route Reunion Island mobile and fix through my own installations. For all other destinations, I need a carrier. I need good wholesale prices to Comoros, Mauritius, Madagascar, India,

Hi List, I would like to know if there is a way to detect gateways which time out (because of network problems or hardware failure for instance) when you send traffic to them. So when you do: Dial(SIP/number@gateway) If a call couldn't get through because the gateway has timed out, i want to do something about it. The idea would be to suspend gateway which time out for 60 minutes,

Greetings, We are currently testing a Sipura SPA-3000 as a gateway from our Asterisk system to a PSTN line for 911 access. We have a number of locations and want to place an SPA-3000 in each, connected to a PSTN line that will provide the correct ANI/ALI information to 911 for each location. It all works great, except for a reasonably significant (4 seconds) delay between when the SPA-3000

Hi List, I've had some issues with some VoIP providers where either: 1 - There is massive PDD but finally the call goes through 2 - There is massive PDD but the call gets rejected anyways I was wondering if there was a way to automatically detect such behaviors when it happens (maybe with a script or something) so I can take the faulty providers out of the routing and maybe automatically

Hi List, I have a 2Mbps SDSL link which gets saturated during peak time because about I have about 3 E1 worth of g729 traffic going thru. So I'm planning to use IAX2 trunking to reduce bandwith requirement and squeeze out each and every bit of this (expensive) bandwith. I've set up two boxes (debian etch), one in a remote data center (which has plenty of bandwith) and one behing

Hey guys. If my Asterisk box connects to the PSTN using SIP and IP over ethernet and doesn't require any authentication, what sort of a trunk would need to be created? Thanks, -- Nick e: nick.hoffman@altcall.com p: +61 7 5591 3588 f: +61 7 5591 6588 If you receive this email by mistake, please notify us and do not make any use of the email. We do not waive any privilege, confidentiality

RAD appear to have bucketloads of products which bridge between various interfaces (E1, BRI, POTS) and their own TDMoIP protocol. The attractive thing about them for me is their availability in Australia. The voip wiki says not much about it (http://www.voip-info.org/wiki/view/TDMoIP), and certainly nothing about if there is any way to get Asterisk to talk TDMoIP. Despite the name, TDMoIP