similar to: RESOLVED - TE405P vs. SoundCard problem (in reality - TE405P No Voice Problem)

My Asterisk server believes that a Digium TE405P and sound are incompatible. Basically, no matter what else I do to the machine it terms of hardware, if the TE405P is installed, none of the playback/background/etc commands work. MOH works fine. So far, I have tried: 1) Seven different PCI soundcards with different chipsets. (Go go Computer Junk Store!) 2) Disabling each and every device

Folks, I'm experimenting with bringing multiple (8) analog lines from our local telco into a Carrier Access ADIT 600 channel bank with an FXO module, then having this talk to Asterisk via the T1 TDM controller on the ADIT and a TE405P card. I don't know if this will work well (ie: give me decent echo cancellation, call disconnect supervision, caller ID etc) but I haven't had much

I am trying to install a TE405P which is to be connected to E1 trunks. I have set the jumpers to E1 (closed), but modprobe wct4xxp still fails with the message: ZT_CHANCONFIG failed for channel 97 - which obviously means the card is still in T1 mode. I have tried everything I can think of, any ideas? TIA

I pulled a working TE405P from one box and put it in another box. I compiled the zaptel modules, modprobe zaptel, modprobe wct4xxp, but no lights on the card come on. I do an lspci and the card shows up there. I ran ztcfg -vv and got the error message Unable to open master device '/dev/zap/ctl' so I followed the instructions in README.udev the error message went away, but now when I

Hi, I am new with asterisk. I am setting a Wildcard TE405P. E1s in Italy come in on a pair of RG-59 coax cables with BNC connectors. So I need an adapter/balun http://www.allcomtlc.com/al_g703n3.htm . I have It but I am not sure that It works. I have configured my asterisk in this way: zaptel.conf span=1,1,0,ccs,hdb3,crc4 dchan=16 bchan=1-15,17-31 loadzone=it defaultzone=it zapata.conf

I'm installing TE405P card. This is my zaptel.conf. -------------------------------------- span=1,0,0,ccs,hdb3,crc4 span=2,1,0,ccs,hdb3,crc4 span=3,0,0,ccs,hdb3,crc4 span=4,0,0,ccs,hdb3,crc4 loadzone = us defaultzone= us -------------------------------------- When i modprobe wct4xxp, -------------------------------------- PCI: Found IRQ 11 for device 02:0b.0 PCI: Sharing IRQ 11 with

I successfully installed asterisk@home 0.6, but when i try to load the wct4xxp module for the TE405P I just got, I get the following: Found TE410P at base address fb7ffc00, remapped to e0220c00 TE410P version c01a009b Tried to load 1c8ac800 into 00000000, but got 188ac800 instead Tried to load 1c8ac000 into 00000001, but got 188ac000 instead Tried to load 07fc07fc into 00000002, but got 03fc07fc

Hi, I'm wondering why zttest shows Best: 99.976 -- Worst: 99.967 -- Average: 99.971469, Difference: 99.971469 Shouldn't it be 100% as timing is hardware and comes from PRI? Am I missing some kernel config? Regards, Atis My /etc/zaptel.conf is span=1,4,0,esf,b8zs span=2,3,0,esf,b8zs span=3,2,0,esf,b8zs span=4,1,0,esf,b8zs #lspci 07:03.0 Communication controller: Digium, Inc. Wildcard

Dear All I installed a Digium card TE405P with zaptel and its running successfully with no alarms, but asterisk is not running . Any one have a cure or advice 03:09.0 Communication controller: Digium, Inc. Wildcard TE405P quad-span T1/E1/J1 card 5.0V (rev 02) Nov 14 07:56:58 localhost kernel: wct4xxp: Clearing yellow alarm on span 2 Nov 14 07:56:58 localhost kernel: wct4xxp: Clearing

Hi all, I'm having some problems getting TDMoE setup for the 1st time. I have a TE405P installed in the main server with an ethernet cross-connection to the secondary machine. (Yes, I know about IAX2 but I want to use TDMoE to simulate using T1s.) I'm using -HEAD from yesterday. On the main machine /etc/zaptel.conf: loadzone = us defaultzone=us

Hi, i am running * 1.0.9 with a newer version of the TE405P. Modprobe wct4xxp and ztcfg are OK. zap show channels only shows me the following. my zapata.conf: [pstn] switchtype=euroisdn pridialplan=unknown prilocaldialplan=unknown usecallingpres=yes busydetect=no ; not need on pri callprogress=no ; was yes but wiki says experimatley could be produce hangups callwaitingcallerid=yes ; show

Hi to all, I have a problem with this wildcard and one E1 line. The server is a Asus P4P800S with the 865PE chipset, and 512MB RAM. The kernel version is 2.4.26. I have donwload and build the latest CVS version of zaptel, libpri and asterisk following the ufficial instructions of digium. I have set up my server in this way: zaptel.conf loadzone=it defaultzone=it

Hello all, We have a TE405P set up with span 1 running to a channel bank, a PRI running into span 2, and a PPP internet T1 running into span 3. We have the first 2 spans up and running without a problem. We have hdlc compiled into the kernel and after making the appropriate changes to zaptel.conf and loading the zaptel, wct4xxp, and hldc modules we can bring up the third span with the internet

Hi, Urgently response would be wonderful, system is a Fedora Core 2. I have a Ericsson BP250 connected to 1 port on the TE405P and another connected to a local telco ISDN30. I have been running CVS-HEAD from about a 2 months ago and upgraded it again just in cause it was a version issue (didn't fix it) but this is what I am getting. When a person calls out from an extension on the BP250 to

We originally purchased a TE405P so we could connect our Asterisk server directly to the T1 PRI from our provider, however due to all the problems reported with T1 PRI's interacting directly with Asterisk, we scrapped that idea and decided to stick with our Cisco router making the conversion to SIP. Anyways, we found a new potential use for it. We have an old location with an existing PBX,

This works fine. Message: 26 Date: Tue, 7 Jun 2005 17:22:23 +0800 From: "Ma Zhiyong" <mazhiyong@sohu.com> Subject: [Asterisk-Users] te405p and dell poweredge To: <asterisk-users@lists.digium.com> Message-ID: <004501c56b42$6a12fcd0$7301a8c0@hylaclient> Content-Type: text/plain; charset="gb2312" Hi, I want to install * and te405p on Dell Poweredge 1850. Can I

http://www.mixdown.ca/~asterisk/ The card seems to be working fine. Don't expect warranty on it though. :-) Why? Because I wanted a quad-span T1 card which worked in the high-end systems I was intending it for, but that I could also keep a few in stock and if the system mainboard failed, pull the card an put it in a standard PC system. I didn't want to have to stock 3.3V and 5V

Anyone care to elaborate on the differences between the T400P and the TE405P? -Darren -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050908/e817f8bb/attachment.htm

Hi I got the 2nd Gen firmware upgraded on the TE405P. I recompiled after putting in the upgraded board but did not change any conf, but the spans become active but will not come up. I guess I am missing something or are the any changes to the zaptel/libpri software that is required. I cannot find any info about this or does this new firmware only work with latest CVS. I am using 1.0.9 with

Hi Everybody, Is there anyone who already uses Asterisk with TE405P card? Is this card going well with the old E400P or T400P drivers? Are there a lot of differences? In the card's data sheet writes this sentece: "Digium has designed the TE405P to be fully compatible with existing software applications..." Is this meaning the the old drivers are also OK for this card? Thank you