similar to: E1 te110p problem

Hi, I wonder if anyone is using Digium's TE110P card on an E1 connection. I have been try to, but so far it wasn't much of a success. It only works more or less in EuroISDN as PRI CPE. And even that config gives me some trouble with channel negotiation. My current config: *zaptel.conf:* span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=be defaultzone=be *zapata.conf:* [trunkgroups]

Hi All, I have configure my Asterisk as follow (using Asterisk@home): [zaptel.conf] span=1,1,0,ccs,hdb3,yellow bchan=1-15,17-31 dchan=16 loadzone = uk defaultzone=uk [zapata.conf] [channels] switchtype=euroisdn pridialplan=local prilocaldialplan=local internationalprefix=00 nationalprefix=0 usecallingpres=yes busydetect=no ; not need on pri callprogress=no ; was yes but wiki says experimatley

Hi guys, I've been installing and configuring a TE110p card. The compile and install went very well. I'm using this on FC4 and I compile with linux26 as well checked I on the udev configs. zttool and ztcfg both indicate that the card is ready. But when I try to "load chan_zap.so" then I get the following Unable to load module chan_zap.so Jan 5 21:43:33 ERROR[6808]:

Hello all. I have here a TE110P (configured as E1) and a TDM400P (with four X100P - FXS). Both boards are recognized by the operating system as showed above: 0000:08:00.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device b1d9:0003 Flags: bus master, medium devsel, latency 64, IRQ 169 I/O ports at e800 [size=256]

Hello, I'm having problem with a wildcard TE110P. As soon as I load the module (wcte11xp for kernel 2.6.10), it spawns a yellow error with or without an E1 plugged-in. Any one managed to set it up in France? Here are my files: zaptel.conf: span=1,0,0,ccs,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 zapata.conf: [channels] language=fr context=default switchtype=euroisdn pridialplan=unknown

I am running Asterisk 1.0.9 and have been running all my calls through a VSP over a IAX2 trunk however we have recently purchased and connected a TE110p to a PRI ( E1 with 16 voice channels ) through Optus. I can make outgoing calls via it fine, however incoming calls are dropped after a few seconds ( or as soon as a command like Playback, or the call is picked up if forwarded to a SIP

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello List, since some days i run into the problem that one span on a TE407P is not comming up correctly. With intense debug on that span i get: < [ 02 01 7f ] < Unnumbered frame: < SAPI: 00 C/R: 1 EA: 0 < TEI: 000 EA: 1 < M3: 3 P/F: 1 M2: 3 11: 3 [ SABME (set asynchronous balanced mode extended) ] < 0 bytes of data

Hi, I bought a Digium Quad E1 card model TE406P. Till now, I can't make it work... I mean, I have red alarm when I configure one E1. The provider is in France (France T?l?com) and I use the following zaptel config : span=1,1,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 I'm using Linux 2.6.15 and when I run ztcfg -vvvv, it seems that all channels are configured... So can someone

Dear users. My current setup uses a euroISDN E1 with 8 cahnnels for incoming and outgoing calls from a digium te110p. Currently all phones use SIP. However, I need to add some faxes lines and some POS credit card machines. These will require POTS lines with a fixed DDI. I have purchased the tdm400p and 4 FXS modules. My problem is with the zaptel.conf and zapata.conf. I am a little confused as

I am trying to use TE110p card for Euro ISDN with Ericsson AMS switch. I consistently get one of the following errors: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 or PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 My zaptel.conf file: -------------------------------- span=1,0,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 loadzone=us defaultzone=us

hi, i'm having problems getting asterisk spliced between an E1 PRI (german Telco Arcor) and an Ericsson Business Phone 250 digital PBX. The Asterisk Server has a TE405P with it's port 1 connected to the E1 PRI provided by our telecommunications provider Arcor and port 2 connected to the E1 PRI of our Ericsson BP250. the setup before: Arcor TelCo PRI(E1)

I have a 'CONGESTION' Status with R2 protocol. While testing this scenario sip GW--?Asterisk ?Digium E1 R2 Protocol?Cisco E1 R2 protocol?sip Gw Find below my error and configuration ,where are the errors in my configuration ? ========================================================================= Connected to Asterisk SVN-branch-1.6.2-r235775 currently running on

Dear All, I'm integrating avaya commuication manager difinity ver 1.0 with asterisk using B2B E1. following are the details of my H/W, zaptel configs and software installed. Digium TE110p asterisk 1.2.19 cent OS 4.4 zaptel 1.2.18 libpri 1.2.4 etc/zaptel.conf span=1,0,0,cas,hdb3 bchan=1-15,17-31 dchan=16 when i ztcfg -vvv im having this error message and the E1 is not getting up. "cas

As these problems are very time sensitive and frustrating, I suggest you document each change you make and do them one at a time so you can actually know what the problem was and not introduce new problems in the process. Find someone who is on the phone quite a bit and will give you an honest evaluation of the call dropping situation (unless you yourself are experiencing this issue too).

I keep getting a red alarm when trying to setup asterisk to use my TE420B EC. I only have a blank context setup in my extensions.conf as I haven't started to config that until I can clear this red alarm. I don't have physical access to the server, so I can't go reseat the modules/card/ethernet cable, though I have hands on location that have done this a couple times

We're rolling out Cisco 7940 phones, linked to *, which is running a TE405p EuroISDN. We have 2 ISDN lines, one we had for testing, and one for general (40+ users) use. During the testing phase, we had 10 phones linked to the second ISDN line, and there were no problems with echo at all. Lucky me. However, since we have started rolling out, we've had quite loud complaints that there is

Hi, thank you for last info. we've tried to use te110p but failed. We're quite surprised that cable wasn't included with the card as any documentation, at least on HW setup and installation, yet cable pinout for connection to PRI interfaces.... 1. We have followed instructions on your site and from Beronet guide, but card just keeps blinking and nothing happens (also no useful

Hi all, Our asterisk PBX, randomly restarts all the channels of the E1 connection. It sends this message "There is no D-Channel, using channel 16 anyway".Then the asteisk recive (or it thinks it recives) yellow alarms at all the B-channels, after that it restart all the channels. When restarting the B-channels it cut all the conversations that is handling at that moment. Does anyone

Hi, I have an asterisk installation with 2 E1 cards Software version is Asterisk 1.2.6 Libpri 1.2.2 Zaptel 1.2.5 I'm having problem with fax transmission, let me explain better my setup: My fist TE110P E1 card is connected to the telco line the second TE110P E1 one to an Nexspan PBX so the server is basically sitting between the line, and the pbx. every call coming from the line is

Hola! I've a Digium E1 card, zaptel recognizes it as (loading the module with debug=1) Setting up DMA (write/read = 321b2000/321b2200) Controller version: 43 Framer: DS21554, Revision: 5 (E1) Found a Wildcard: Digium Wildcard E100P E1/PRA Using CCS/HDB3 coding/framing with CRC4 120 Ohms Calling startup (flags is 4099) Started DMA Got interrupt: 0x0005 /etc/zaptel.conf: