Arnar Gestsson
2006-Jan-05 14:48 UTC
[Asterisk-Users] TE110p and pri_cpe signalling not recognized
Hi guys, I've been installing and configuring a TE110p card. The compile and install went very well. I'm using this on FC4 and I compile with linux26 as well checked I on the udev configs. zttool and ztcfg both indicate that the card is ready. But when I try to "load chan_zap.so" then I get the following Unable to load module chan_zap.so Jan 5 21:43:33 ERROR[6808]: chan_zap.c:10546 setup_zap: Unknown signalling method 'pri_cpe' Jan 5 21:43:33 ERROR[6808]: chan_zap.c:10171 setup_zap: Signalling must be specified before any channels are. Jan 5 21:43:33 WARNING[6808]: loader.c:414 __load_resource: chan_zap.so: load_module failed, returning -1 My config is here below. TIA Arnar Gestsson /etc/zaptel.conf span=1,1,0,ccs,hdb3,crc4 loadzone = nl loadzone=de defaultzone=nl bchan=1-5,7-15,17-31 dchan=16 /etc/asterisk/zapata.conf [trunkgroups] trunkgroup => 1,16 spanmap => 1,1 [channels] language=en context=default switchtype=euroisdn pridialplan=unknown signalling=pri_cpe ;rxwink=300 usecallerid=yes hidecallerid=no callwaiting=yes usecallingpres=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes cancallforward=yes callreturn=yes echocancel=yes echocancelwhenbridged=yes rxgain=5.0 txgain=1.0 echotraining=yes group=1 callgroup=1 pickupgroup=1 immediate=no channel => 1-15,17-31 -- Arnar Gestsson <age@trackwell.com>
Domjan Attila
2006-Jan-05 15:01 UTC
[Asterisk-Users] TE110p and pri_cpe signalling not recognized
Hi, I think you didn't install the libpri. On Thu, 2006-01-05 at 22:48 +0100, Arnar Gestsson wrote:> Hi guys, > > I've been installing and configuring a TE110p card. The compile and > install went very well. I'm using this on FC4 and I compile with > linux26 as well checked I on the udev configs. > > zttool and ztcfg both indicate that the card is ready. > > But when I try to "load chan_zap.so" then I get the following > > > Unable to load module chan_zap.so > Jan 5 21:43:33 ERROR[6808]: chan_zap.c:10546 setup_zap: Unknown > signalling method 'pri_cpe' > Jan 5 21:43:33 ERROR[6808]: chan_zap.c:10171 setup_zap: Signalling must > be specified before any channels are. > Jan 5 21:43:33 WARNING[6808]: loader.c:414 __load_resource: > chan_zap.so: load_module failed, returning -1 > > My config is here below. > > TIA > > Arnar Gestsson > > > /etc/zaptel.conf > > span=1,1,0,ccs,hdb3,crc4 > > loadzone = nl > loadzone=de > defaultzone=nl > > bchan=1-5,7-15,17-31 > dchan=16 > > /etc/asterisk/zapata.conf > > [trunkgroups] > trunkgroup => 1,16 > spanmap => 1,1 > > [channels] > language=en > context=default > switchtype=euroisdn > pridialplan=unknown > signalling=pri_cpe > ;rxwink=300 > usecallerid=yes > hidecallerid=no > callwaiting=yes > usecallingpres=yes > callwaitingcallerid=yes > threewaycalling=yes > transfer=yes > cancallforward=yes > callreturn=yes > echocancel=yes > echocancelwhenbridged=yes > rxgain=5.0 > txgain=1.0 > echotraining=yes > group=1 > callgroup=1 > pickupgroup=1 > immediate=no > channel => 1-15,17-31 > > >-- Domjan Attila <adomjan@tvnet.hu>
stotaro
2006-Jan-05 15:17 UTC
[Asterisk-Users] TE110p and pri_cpe signalling not recognized
I had this problem and while not 100% sure. I think the solution was whitespace at the end of the lines in the conf file. Opened the file with vi, went to each line and hit end to make sure there were no extra spaces, there were, removed them, rebooted and issue went away.> Hi guys, > > I've been installing and configuring a TE110p card. The compile and > install went very well. I'm using this on FC4 and I compile with > linux26 as well checked I on the udev configs. > > zttool and ztcfg both indicate that the card is ready. > > But when I try to "load chan_zap.so" then I get the following > > > Unable to load module chan_zap.so > Jan 5 21:43:33 ERROR[6808]: chan_zap.c:10546 setup_zap: Unknown > signalling method 'pri_cpe' > Jan 5 21:43:33 ERROR[6808]: chan_zap.c:10171 setup_zap: Signalling must > be specified before any channels are. > Jan 5 21:43:33 WARNING[6808]: loader.c:414 __load_resource: > chan_zap.so: load_module failed, returning -1 > > My config is here below. > > TIA > > Arnar Gestsson > > > /etc/zaptel.conf > > span=1,1,0,ccs,hdb3,crc4 > > loadzone = nl > loadzone=de > defaultzone=nl > > bchan=1-5,7-15,17-31 > dchan=16 > > /etc/asterisk/zapata.conf > > [trunkgroups] > trunkgroup => 1,16 > spanmap => 1,1 > > [channels] > language=en > context=default > switchtype=euroisdn > pridialplan=unknown > signalling=pri_cpe > ;rxwink=300 > usecallerid=yes > hidecallerid=no > callwaiting=yes > usecallingpres=yes > callwaitingcallerid=yes > threewaycalling=yes > transfer=yes > cancallforward=yes > callreturn=yes > echocancel=yes > echocancelwhenbridged=yes > rxgain=5.0 > txgain=1.0 > echotraining=yes > group=1 > callgroup=1 > pickupgroup=1 > immediate=no > channel => 1-15,17-31 > > > > -- > Arnar Gestsson <age@trackwell.com> > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > Asterisk-Users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > > > -- > No virus found in this incoming message. > Checked by AVG Free Edition. > Version: 7.1.371 / Virus Database: 267.14.13/221 - Release Date: 1/4/2006 > >