similar to: can't get TDM400P to answer

Displaying 20 results from an estimated 6000 matches similar to: "can't get TDM400P to answer"

2005 Mar 16
0
Problems with TDM400P and asterisk on Linux 2.6
Hi there, I have a TDM400P (1 x fxs, 1 x fxo) which I'm attempting to run on linux 2.6 (gentoo), without much success at the moment. I have previously had it working on a 2.4 installation, but when I moved to a new box and installed a 2.6-based system, it failed to work. In both cases I'm using whatever (libpri, zaptel, asterisk) is checked out by default (I assume that means HEAD)
2005 Aug 12
3
TDM400P FXO channel hookstate always "Offhook" & outbound digits sent before provider dialtone
I have an Asterisk@Home 1.3 server (Asterisk 1.0.9) and recently added a TDM400P with (1) FXO card on port 4. Inbound calls are always successful but outbound calls fail 75% of the time with intercept messages from my dial tone provider that include "we're sorry, your call did not go through", and "we're sorry, when placing a local call it is now necessary to dial an area
2007 Apr 30
1
TDM400P and Junghanns QuadBRI issue
Hi List, I'm setting up a system with one TDM400P (2*FXO + 2 * FXS) and one Junghanns QuadBRI on a Fedora Core 6 (Kernel 2.6.20-1.2944.fc6). I'm using the bristuff-0.3.0-PRE-1y-e kit. It download zaptel-1.2.16, libpri-1.2.4 and asterisk-1.2.17 When it's the time for ztcfg to do its job it complains with <ZT_SPANCONFIG failed on span 2: No such device or address (6)>
2005 Aug 13
3
TDM400P Card (Rev G) with bad FXS module?
I think I have a bad FXS module on my TDM400P. Channel map: >> >> Channel 01: FXO Kewlstart (Default) (Slaves: 01) >> Channel 02: FXS Kewlstart (Default) (Slaves: 02) >> >> 2 channels configured. >> ZT_CHANCONFIG failed on channel 1: No such device or address (6) The zaptel loads ok, but the wctdm reports No such device or address and stays loaded. The
2009 Apr 11
1
asterisknow 1.5 with X100P and TDM400P
Hi All, Sorry if this has been around a millions times.. I have been off this list for a few months now.. I have installed the latest asterisknow (upgraded asterisk to 1.6 as well) and I am having a hard time getting my X100P and TDM400P working.. Its all new to me with dahdi because my old server is still running Asterisk 1.0.2 so there have been lost of changes.. Can someone point me in
2009 Nov 12
5
my kernel is dazed and confused
Nov 12 08:54:27 steerpike kernel: Uhhuh. NMI received for unknown reason a0 on CPU 0. Nov 12 08:54:27 steerpike kernel: You have some hardware problem, likely on the PCI bus. Nov 12 08:54:27 steerpike kernel: Dazed and confused, but trying to continue Would my Digium TDM410P cause an NMI, or is my computer failing? - Mike
2005 Aug 12
2
Possibly bad FXS module in TDM400P?
I've got the latest zaptel and cvs asterisk software loaded on my phone server running FC3. And yes, It's fully updated and udev is setup correctly. I've got a TDM400P with one FXS and one FXO module installed. When I load zaptel and wctdm and run ztcfg -vvv, I get this: [root@asterisk ~]# ztcfg -vvv ZT_CHANCONFIG failed on channel 1: No such device or address (6) Zaptel
2006 Jan 31
1
Asterisk 1.2.1 + TDM400P + fax machine unreliable ?
Hi, I have a running asterisk 1.2.1 (bristuffed) with a TDM400 Board. Connected to 1 port is am ordanary Fax Machine. Everything 'seems' to work, however receiving faxes is very unreliable. Sometimes I receive a normal page, without problems. Sometimes half of a page and the rest is scrambled, but most often, I receive nothing and the other site reports a Fax error... The Fax machine
2007 Nov 20
1
FXO Hangs up automatically
Hi, I'm having problems using a TDM400P Card. I put my SIM card in a Nokia Premicell and connected it to a TDM400P card but when I make calls to the number, it hangs up automatically. The card also can't call out. Any ideas? I've searched the archives without much success. I appreciate all your help. Details: I'm using Asterisk 1.2.17 on Fedora Core release 5 (Bordeaux). On an
2009 Mar 15
1
No hardware timing source found in /proc/dahdi
Hello all, Ok it is Sunday afternoon and I am going crazy. I have been running in circles so long that I can't think straight. As an example, I sent this message to the wrong address the first try, AAARRRRGGGGGGHHHHH. I have Asterisk 1.6.0.6 and DAHDI Tools Version - 2.1.0.2, DAHDI Version: 2.1.0.4, OpenSuSE 10.3 x86_64, tdm422 at the end of installing dahdi-linux and dahdi-tools I get:
2006 Jan 19
1
TDM400P zttest not working
Hi, I have a TDM400P running with only one FXO port running on a VIA EPIA MS10000 (1Ghz Via Eden). When I run zttest from Zaptel 1.2.1 it hang and when I interrupt it with Ctrl-C that is the result: ?anyone have some idea about why isn't working? Some additional info: # /usr/src/zaptel/zttest -v Opened pseudo zap interface, measuring accuracy... --- Results after 0 passes --- Best:
2011 Apr 02
1
Problem getting TDM400P clone card to go off-hook and dial
I am having problems getting a Nicherons TDM400P wildcard clone to dial out. Everything appears to be configured correctly, but although I see call progress, it never seems to actually pick up the phone. (The following is a test of 911 emergency, where I substitute 811 [repair service] as the actual number dialed.) *CLI> -- Executing [911 at from-internal:1]
2008 Apr 14
4
Unable to load module chan_zap.so
I am having trouble with chan_zap.so not loading. When I load it from modules.conf, Asterisk bails out without any error message. When I load it from the console, it just says "Unable to load module chan_zap.so" no matter what verbose level I am using. dmesg says: Zaptel Version: 1.4.4 Zaptel Echo Canceller: MG2 Freshmaker version: 73 Freshmaker passed register test Module 0:
2005 Jun 22
4
TDM400P DevKit Problem
I installed the TDM400P and installed it on a system running on Fedora Core1, please refer to the steps below. I connected an analogue phone to the FXS port. When I pick up the speaker I don't hear the dialtone although when I press a number key I hear a DTMF generated. What could be the problem? I appreciate your help 1- First I installed the TDM400P in the PCI slot and connected
2008 Feb 25
4
TDM400P dialout problem
Using asterisk 1.4.18 and zaptel 1.4.9 on x86_64, I am having trouble dialing out to the pstn. The call is initiated at Zap/1-1 and should exit via Zap/3. I get the following: -- Starting simple switch on 'Zap/1-1' -- Executing [2111 at internal:1] Dial("Zap/1-1", "Zap/3/8801234") in new stack [Feb 25 02:36:59] DEBUG[7194]: chan_zap.c:1954 zt_call: Dialing
2005 Mar 27
0
analog phone
Hi I have been searching the wiki and mailing lists and I cant see where my config is incorrect. I have a Digium tdm11b (1 fxo + 1 fxs) this is the output of cat /etc/zaptel.conf # Autogenerated by /usr/local/sbin/genzaptelconf -- do not hand edit # Zaptel Configuration File # # This file is parsed by the Zaptel Configurator, ztcfg # # It must be in the module loading order # Span 1: WCTDM/0
2005 Jan 24
0
TDM400P Sync source
Hi, I am trying to track down the reason to my problems with sending and reciving fax with my PRI and 2 TDM400P Cards: PSTN <-> PRI (E100P) <-> * <-> TDM400P <-> Fax Machine I have used Zapbarge to listen to the data stream, but I can't say if it really have some time slips - fax kinda noisy in itself. Using the zttool i saw the Sync source for the TDM are
2009 Nov 23
0
TDM400P alarm state
I'm having real problems with my connection to BT, it is a home line, but after a while it sets an alarm and only a restart of asterisk resets it could some one look at the below configs and suggest any changes to make this more reliable Thanks for your help Robb asterisk version 1.6.1.10 dahdi version SVN-trunk-r7445 dahdi_scan active=yes alarms=OK description=Wildcard TDM400P REV I
2009 Mar 10
3
configuring channels for dahdi
after installing asterisk 1.4.23.1 and dahdi-linux-2.1.0.4 and at CLI> module load chan_dahdi.so receive the following: signalling must be specified before any channels are. CLI> Warning [4663]: chan_dahdi.c:11627 process_dahdi: Ignoring signalling Error[4663]: chan_dahdi.c:10946 build_channels: Unable to reconfigure channel '1' Error[4663]:
2009 May 20
1
Channels configuration with DAHDI
-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all! Days ago I bought a OpenVox A400P card with a port FXS and another FXO that I am testing with my Asterisk installation in my house. I'm using Asterisk 1.4.24.1 with DAHDI Linux 2.1.0.4 and DAHDI Tools 2.1.0.2 on Debian GNU/Linux Lenny. I was reading "The future of telephony" and this [1] document looking for information about