similar to: Sync Source: Internally clocked

I have 7965 and am trying to convert the firmware to SIP (SIP45.8-3-4SR1S). Does anyone have a valid XMLDefault.cnf.xml they could share? I have tried the version at voip-info<info.org/wiki/view/Asterisk+phone+cisco+79x1+xml+configuration+files+for+SIP&view_comment_id=14768#Troubleshooting>for the 7941/7961 but unfortunately /var/log/messages shows in.tftp stops sending after

<P>hi Everyone,</P> <P>We are configuring an ISDN PRI E1 with an E100P card, when you load the drivers, and starts the asterisk, cards also starts fine, givin following output,</P> <P>*CLI> <BR>&nbsp; == D-Channel on span 1 up<BR>&nbsp;&nbsp;&nbsp; -- B-channel 1 successfully restarted on span 1<BR>&nbsp;&nbsp;&nbsp; --

Hi, I configured an asterisk box with 1 Digium Wildcard TE110P T1/E1 Card 0 I setup the jumper in e1 position. my zaptel.conf : defaultzone=it loadzone=it #gestione PRI span=1,0,0,ccs,hdb3,crc4,yellow bchan=1-15 # set this to 1-15,17-31 for E1 dchan=16 # set this to 16 for E1 bchan=17-31 # set this to 1-15,17-31 for E1 # Asterisk starts correctly, I see th 30 channels. Anyway I cannot put

Hi ! I'm trying to configurate my first asterisk system. My test plant has an E100P Card and a 4 FXS TDM 400P card. I've an E1 configured for 15 channels. Telco says that crc4 is configurated so my zaptel.conf is: loadzone = it defaultzone=it span=1,0,0,ccs,hdb3,crc4 bchan=1-15 dchan=16 unused=17-31 fxoks=32-35 zttool shows no alarms. I've also tried changing the timing

Hi, I'm trying to connect a PC with a TE410P to an E1/IP equipment. Unfortunately I keep getting a yellow alarm from zaptel (in zttool) and a Loss of Framing alarm on the remote equipment. The E1/IP is connected on the other side to a PRI interface on a GSM MSC. I have configured the span as: span=1,1,0,ccs,hdb3 (also tried span=1,0,0,ccs,hdb3) and the channels as: bchan=1-15,17-31

Hi I'm having difficulties getting up my TE110P (running as a E1) when I connect it to the PRI. If I start the server with a loopback connector everything seems fine and the led is green but when I connect it to the PRI the flashing starts .... I can't seem to find anything in the log that suggests what could be wrong .....Aug 8 11:33:00 DEBUG[1369]: Updated conferencing on 31,

Perhaps everything isn't as spiffy as I thought When running zttool the card still reports as internally clocked Zaptel.conf: # Global data span=1,1,0,ccs,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 loadzone=se defaultzone=se And as pointed out by Peter I do get a lot of D-channel warnings ... Aug 9 16:21:25 NOTICE[1350]: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 And

<p>I am new to the group but have searched the doc's FAQ's etc before posting here.</p><p>&nbsp;We are attempting tie our asterisk server/service to the building's PBX, the building is in the UK and the local PBX is a meridian option 11 installed and mainteined by BT.</p><p>BT Have installed a NTBK50AA E1-PRI card in the meridian with daughter cards

Hello, I have a problem with zaptel. I hope you can help me. I installed and configure zaptel. ZAPTEL.CONF span=1,1,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 loadzone = de defaultzone=de But the output of cat /proc/zaptel/* Span 1: WCT1/0 "Digium Wildcard TE110P T1/E1 Card 0" (MASTER) HDB3/CCS/CRC4 RECOVERING 1 WCT1/0/1 Clear (In use) RED

Hi, Has anyone connected * to a Colt E1 line in Europe? If so could you send me the zaptel.conf and zapata.conf. Thanks, Aaron __________________________________ Do you Yahoo!? New and Improved Yahoo! Mail - Send 10MB messages! http://promotions.yahoo.com/new_mail

Hi to all, I have a problem with this wildcard and one E1 line. The server is a Asus P4P800S with the 865PE chipset, and 512MB RAM. The kernel version is 2.4.26. I have donwload and build the latest CVS version of zaptel, libpri and asterisk following the ufficial instructions of digium. I have set up my server in this way: zaptel.conf loadzone=it defaultzone=it

I need your help I have a sangoma A104D on my dell server; I got card status ok with no alarm If I dialed the extension 6210006, it shows the output as stated below, but there is no ringing from the pstn number nor the iax softphone am using on my pc. I will be glad if someone can give me a working config? What I want to achieve is to send all my call to the pstn on A104D? The pstn am

Hi All, This is our 2nd E1 client that we try to use crc4 either with the e100p or with the e405p without luck. After some trials, we ask the telco to switch off crc4 on their side and everything works flawlessly. Is there anything in the crc4 calculation that may be broken? We took a look at wct1xxx.c and wct4xx.c but there doesn't seem to be much there to be fixed (apparently the crc4

Hello, I have an E100P, and in the zaptel.conf I have: span=1,1,0,ccs,hdb4,crc4,yellow fxsks=1-10 the light on the card is green( BTW what do all those states of the card that zttool reports YELLO, RED, BLUE ..., is there a doc for zttool?, or for the card?) in the asterisks` zapata.conf I have: [channels] context=default switchtype=euroisdn signalling=fxs_ks usecallerid=yes hidecallerid=no

Skipped content of type multipart/alternative

Hi All, I'm having problems trying to get a TE120P operational in Canada. I keep getting a congestion error when I try to make a call. I'm not sure if my switching, parity, etc is correct. I'm hoping that someone will be able to verify my config. The Telco is SaskTel, with a 10 channel 50 DDI service. Zap show channels show and ztcfg -vv looks ok and the zttool show

I have a TE205P, jumpered for E1, added the missing wct4xxp-line to /etc/modprobe.d/zaptel, zaptel.conf is just span=1,1,0,ccs,hdb3,crc4,yellow span=2,2,0,ccs,hdb3,crc4,yellow bchan=1-15 dchan=16 bchan=17-31 bchan=32-46 dchan=47 bchan=48-62 Which, according to my reading of the documentation I could find, should be correct. ztcfg doesn't complain about anything, yet all I ever get is RED

Nik, I'm not sure that "NOP" is correct, but I'm in the states so I'll to defer to someone who knows E1/PRI. When I run zttool I have "OK" under the alarms. Is there a way you can call the telco and confirm the settings? Make sure that framing, coding and D channels are set up on their end the same way you're set up. As for asterisk, here's what I get

Hi guys, I've been installing and configuring a TE110p card. The compile and install went very well. I'm using this on FC4 and I compile with linux26 as well checked I on the udev configs. zttool and ztcfg both indicate that the card is ready. But when I try to "load chan_zap.so" then I get the following Unable to load module chan_zap.so Jan 5 21:43:33 ERROR[6808]:

Hi all, Our asterisk PBX, randomly restarts all the channels of the E1 connection. It sends this message "There is no D-Channel, using channel 16 anyway".Then the asteisk recive (or it thinks it recives) yellow alarms at all the B-channels, after that it restart all the channels. When restarting the B-channels it cut all the conversations that is handling at that moment. Does anyone