similar to: Adit 600 and echo

Digium X100P / new cards are is available on ebay for $43. http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=3073050567&category=3309 <http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=3073050567&category=3309 > Hope this helps to who want to play with X100P! Are these being sold by Digium ? I don't know ?? - SamW -------------- next part -------------- An HTML

101's for 68.00 http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=3042066051&category=11175 102's for 79.95 http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=3042066389&category=11175 Just passing what I find along.... bkw

The Orion echo canceller is just ok. The Tellabs units work just as well if you don't mind 10 mins of soldering. I have the orion running with an adit 600 and a TE110P. Echo cancel is fairly good, but I have loads of problems with DTMF digits. -Darren ________________________________ From: asterisk-users-bounces@lists.digium.com

Hi, Not sure if anyone will be intersted but I have put together an install guide for Asterisk on RedHat 9.. Its nothing special but it may be of use to the newbies.. Like me.. If you would like a copy let me know and I will send it to you.. later.. -- ______________________________________________ http://www.linuxmail.org/ Now with e-mail forwarding for only US$5.95/yr Powered by Outblaze

If anyone is looking, I just ran accross an ebay auction for X100P Cards at what I thought was a very reasonable price. http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=3046843672&category=48483&rd=1 --------------------------------- Do you Yahoo!? Yahoo! SiteBuilder - Free, easy-to-use web site design software -------------- next part -------------- An HTML attachment was

Is this an acceptable machine or does it have to be "rackmount" ? http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=250111166910 - rh -- Abba Communications Spokane, WA www.abbacomm.net

Since i'm sure there are others out there in the same position as me, being disappointed that the original T400P and E400P cards are no longer available from Digium, I thought I would pass on a place I found to get them. I needed the older card, since I didn't want to have to get a motherboard with 3.3v pci slots on it.

Another question, Is anybody using the Tellabs 2572 EC with a PRI. When we moved from our analog lines to a PRI, I thought it would be simple stuff moving the EC to the PRI. Changed signaling, made sure that channel 24 wasn't being ECd and everything came up. But, I was getting complaints of random echo on the PRI. Local echo. Also, we weren?t able to do any kind of modem dial-outs (Adit

I've been reading the Google searches trying to understand how to tie together Adit 600 to Asterisk to provide 2 way service. I'm about blind from reading. I assume, the answer is using MGCP between the boxes. However, the examples I found don't really explain fully enough to know how to modify examples to work for me. I'll have in the ADIT with T1's. There is a CMG and

Has anyone had any success using the Adit 600 with the CMG card talking MGCP to asterisk? I want to have a central asterisk server with 10 Adit 600's at various locations providing 24 FXS ports.... Thanks, Isaac

I have an adit 600 with an fxo card connected to a digium T1 card. If I try to make an outgoing call and the T1 cable is disconnected, asterisks returns congested like it should. But, if the adit 600 is connected to the T1 card, the adit 600 immediately "answers" the call even if there are no physical lines attached. I even removed the fxo card and the adit 600 still

Ok, I've pretty much decided to try the Adit route. Somebody who has experience with these tell me if I'm missing something. I have 15 incoming PSTN lines. T1 is not an option at current location. I want to put in an Adit 600 with 2 8-port FXO boards. The adit will then connect to * via a digium t1 board. I configure zaptel.conf for the T1. What other parts would be needed? How do

Folks, I'm experimenting with bringing multiple (8) analog lines from our local telco into a Carrier Access ADIT 600 channel bank with an FXO module, then having this talk to Asterisk via the T1 TDM controller on the ADIT and a TE405P card. I don't know if this will work well (ie: give me decent echo cancellation, call disconnect supervision, caller ID etc) but I haven't had much

Hello, I am connecting Asterisk to an Adit 600 via a T100P. Unfortunately I am not able to get any lights on the T100P and the Adit 600 only shows red. I have already modprobed the t100p. Has anyone successfully connected these before? I've tried both a cross-over cable and a standard cat 5 cable, but I can't seem to get them to work. Any suggestions? Thanks! Craig

Say I get an ADIT 600 with two FXS8A and one FXO8A from ebay. a. Is it good for Asterisk? b. How do I connect the extensions and lines to it? Do I need a special jack? Can I get that jack in every corner? c. where can I find help for configuring it? d. what kind of backup does it have? Does it need to be reconfigured after a power outage? Shoval Tomer, IT Manager, SofTov Advanced Systems, Ltd.

Did CentOS get an alpha yet How does this one look? http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=160115818814 will it do the job or not? - rh -- Abba Communications Spokane, WA www.abbacomm.net

Hi, I'm using an Adit 600 Channel Bank with *. I love it and it works really great for my FXS lines. One problem that I have with it (It's really not a problem yet, but it's a potential one) is that I've scoured the manaual for the Adit to see if there's a way to dump out a config file from the bank so in the event of a power and battery failure I don't have to type in the

Got at suggestion from CarrierAccess to use the Adit 600 as an VoIP router using MGCP IP protocol, instead of controlling it through an E1. Have anyone tried this configuration? How does MGCP works? I've tried to search for it on Google, but I only find the protocol specification for it. Is Asterisk fully capable of this? I can't find any documentatin covering the use of MGCP in Asterisk.

I am trying to find a manual for the Carrier Access Adit 600. Does anyone know where I might be able to find one? Thanks -Jon -- Jon J. Brandon jon@monsoonretail.com http://www.monsoonretail.com

I've finally got my Adit 600 and are configuring it right now. But I have to say, there aren't much documentation for it. I've setup MGCP and Asterisk seems to find it. But all channels (40 FXS channels) are "Down"! But the MGCP itself is "Up" according to the statistics. I can't find any documents how to set each channel to "Up" in the CLI. Any