similar to: Re: Problem with blind transfer and Polycom phones !! more info

I'm working on replacing a SoundPoint 600 with a 650. I need to merge these two sets of digitmaps in the polycom sip.cfg file, because the 650 locks up when I try to use the digitmap from the 600. I've included the default digitmap from a 3.1.3 RevB polycom release. I'd like to merge these two digitmaps, but I don't want to reintroduce the lockup issue I was having with the

This is a dialpaln issue. I solved the same problem recently. For 4 digit extensions you need to append the dialplan statement in the sip.cfg configuration file as follows <digitmap dialplan.digitmap="[2-9]11|0T|011xxx.T|[0-1][2-9]xxxxxxxxx|[2-9]xxxxxxxxx|[2 -9]xxxT|1xxxT" dialplan.digitmap.timeOut="3"/> Michael > I am not sure what I did but blind transfers do not

I'm replacing a SoundPoint IP 600 with a SoundPoint IP 650. I attempted to simply reuse the existing config files for the old phone on the new phone, but the new phone would lock up on the 4th digit when attempted to dial out certain numbers. So, I downloaded the newest firmware and config templates from Polycom, and attempted to migrate the settings. Seems I'm missing something from

I recently had a bear of a time getting a Polycom Soundpoint 500IP up and registered.. Now that its registered I ran into a problem w/ the dialplan. Needing to dial x101 I'd dial 10 - then get a fast buzy.. Also making a local call - dialing 95551212- would give me a fast busy after the 7th digit - so 9555121.. Same w/ LD calls... This dialplan really got me down as I didn't find

I'm using Polycom Soundpoint phones and I want to use some extensions beginning with # for features setup. I'm getting the fast busy "can't match it" signal. I want to match #50 for call forwarding, for instance, and #505551212 to set the call forwarding number and turn it on. I have tftp set up and sip.cfg contains the following: <dialplan

I was hoping that someone may be able to shed some light on some issues I'm having on trying to get an Asterisk test server up and running. At the moment I have the basics, two Polycom hard phones (301 & 601 with expansion unit (which oddly will not power up)) that can call each other, log into voicemail (one touch) and have custom directories & buddy lists. Unfortunately some of the

<digitmap =20 dialplan.digitmap=3D"[2-9]11|0T|011xxx.T|[0-1][2-9]xxxxxxxxx|[2-9]xxxxxxx= x x|[2-9]xxxT" dialplan.digitmap.timeOut=3D"3|3|3|3|3|3"/> Don't think it's been modified from the original supplied. ...brig -----Original Message----- From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at lists.digium.com] On Behalf

I'm stumped on this one and any help would be greatly appreciated. I'm just trying to get my Polycom 601 to have multiple extensions on it. For example, on line 1 I want extension 21, on line 2 I want extension 22, and on line 3 I want extension 23. Ideally I'd actually have each extension appear on 2 lines and therefore filling up all 6. I should be able to do that with the

I am using Polycom 501s with asterisk 1.2.4. When transfering to call parking wih "#1" -> 700 the user is able to hear asterisk tell him what extension the call was parked on. However, when I press "transfer" -> blind -> 700 . The user is not able to hear what extension the call was parked on. It seems like the polycom is hanging up before asterisk is able to

I'm running Asterisk 1.2.8 with Polycom ip501's xten softphones The only problem I'm experiencing is the following: I can't seem to get blind transfers to work with my Polycom 501 phones Either through the feature code or the soft keys. Feature code blind transfers: I set up a feature map in features.conf like this: blindxfer => # This works for all my

Hi all. I just installed bunch of IP450's and everything went well and my customer is happy.... except that they are unable to transfer calls to other extenstions. They can dial them directly just fine. However, when the user is in a call and presses the transfer soft key, they get dial tone, and start typing the extension, say 1008. But by the time they get 100 typed in, the phone tries

> >> Jason Brown wrote: > >> | Anyone have experiece with polycom phones? > >> | > >> | I am experiencing a really weird problem. In an office > where I have > >> | the following extensions: > >> | On the Polycom phones, when I want to dial from extension > >> 100 to any > >> | extension 120 or above, or dial out, it

Any Polycom gurus out there? If so, I have a few config file questions. First off, does anyone have the daylight savings time rules written for this Sunday's big change? Secondly, if there any way in the config file to tell the phone not to display the number of missed calls? I don't mind it keeping the missed calls list, I just don't want that running count. Lastly, I am trying

Just installed Asterisk 1.2 on a brand new clean machine running RedHat 9.0. I have a TDM400 card inside. When I boot, the card seems dead. When I do: modprobe wctdm modprobe Zaptel the lights come on and all seems fine, until I reboot that is... After a reboot I have to repeat the modprobe. I shouldn't have to do a modprobe every re-boot should I? How do you get the drivers to load

Hi Andrew - > On Monday 13 March 2006 10:20, Noah Miller wrote: >>> The transer button on the polycom phone does not seem to transfer/park >>> the call properly. I have to use the # -> 700 to park the call. >> >> If I recall, using the Polycom transfer, you have to make sure it is done >> as a blind transfer. The Polycom attended transfer

I have four Polycom 330 phones connected to an asterisk system. There are other VoIP phones connected too. All of the extensions are four digits beginning with 11. From any of the phones, except the Polycom, picking up the handset to call extension 1103 for example works fine. With the Polycom 330, as I press the second 1 of 1103 it stops taking input and gives me an error. I tried

I don't know if Polycom decided to change their policy or not, but I just went to their website and when you click on the downlooad link, it will now present you with an option to join their extranet. I did that and I got the following message immediately: <snip> Access to certain Resource Center sections and content are subject to approval. Eligible members, will receive further

We upgraded to Asterisk 1.4.13 earlier this week, and now an odd problem has cropped up with our Polycom phones. Basically, performing a transfer via the transfer softkey fails on transfers to extensions beginning with a *. When you try, you just get a fast-busy, and next to nothing on the console (usually a message about the peer being unable to authenticate) This is only affecting

Hello, I have a mixture of Polycom SP IP 500 and 300 phones. I have been reading through the administration manual to try and solve this problem, but I do not seem to be able to find the answers to my question. I figured I would ask here and see if anyone has some suggestions. The problem is kind of annoying. After dialing 4 digits, the phone seems to pause and miss the 5th digit, often

Hi All, I'm not sure if this is related directly to asterisk or not but on my Polycom 320 when I try to dial a number smaller than 4 digits I get an error on the phone saying "Enter more digits". The dial plan section is listed below. <dialplan dialplan.impossibleMatchHandling="0" dialplan.removeEndOfDial="1"> <digitmap