Displaying 20 results from an estimated 800 matches similar to: "Adit 600 FXO card sound quality"
2004 Jan 17
1
Channel Bank Woes...
Hello all,
I have a new Carrier Access Adit 600 and am having a problem dialing out
and receiving incoming calls.
After the initial ring, the calling party will here nothing. There is a
silence, but the SIP phones that is supposed to ring will ring. The
calling party will not hear the sound of the ring that * sends out on
the line. Additionally, if someone picks up the receiver there is no
2004 Jul 31
0
Trunk doesn't work Adit 600/T100P
Hi !
I am connecting to Adit 600 thru a T100P card
I have configured 1-16 FXS channels and 17-24 FXO.
Everything looks fine on Asterisk side I get a tone
on all FXS channels, but when I try to dialout thru
one of the FXO channels 17-24 it doesn't connect to
the POTS line and echoes back my voice.
I use fxsls and fxols for the T1 channels and ls on
Adit side. Whats wrong here ?
here is my Adit
2004 Jun 28
2
Adit 600 - Getting Dial Tone
Hello, I have an Adit 600 (3 FXS cards) hooked up to a digium T1 card in my
asterisk box. I 'connected' the slots to the a:1 T1 interfaces via the
command line. The slots (3 fxs) are configured with 'ls' signaling. I
configured the T1 card with the same line settings as the T1 interfaces on
the adit and I get green lights on both the T1 card and the T1 interface on
the adit (so
2004 Jul 25
3
FXS vs. FXO
Hello,
I've recently purchased Adit 600 with 3FXS and 1FXO to be connected to
my * server via T100P card. This is the output of "status equipment"
command in the Adit600:
For some reason the FXO card is seen as FXS, why? Is it ok? On the card
it is written "FXO".
Regards,
Shlomi Bachar
-------------- next part --------------
An HTML attachment was
2004 Jan 13
3
How to Order Disconnect Supervision from SBC using Adit 600?
Can anyone help me with the term that SBC uses to refer to disconnect
supervision? I have an Adit 600 channel bank which has helped improve the
disconnect detection time down to about 8 seconds. This is still causing some
issues in particular with call progress enabled in * we are having a few
disconnects while calls are in session (about 2 reported in first 5 days of use).
I have talked both to
2004 Apr 15
2
TE405P + Adit 600 and FXO module - should this work?
Folks,
I'm experimenting with bringing multiple (8) analog lines from our local
telco into a Carrier Access ADIT 600 channel bank with an FXO module, then
having this talk to Asterisk via the T1 TDM controller on the ADIT and a
TE405P card.
I don't know if this will work well (ie: give me decent echo cancellation,
call disconnect supervision, caller ID etc) but I haven't had much
2004 Oct 06
0
Echo / Adit 600
We have an Adit 600 with some fxo lines.
Callers calling in on the fxo ports do not hear echo, but the
party answering hears bad echo.
Here is the gain settings on the Adit:
Corporate Adit 600> show 1
SLOT 1:
Settings for FXO: Channel 1:
Signaling: LSCPD
RxGain: -2 dB
TxGain: -3 dB
And here are the zap settings:
busydetect=no
callprogress=no
2005 Jan 27
2
Adit 600
Has anyone had any success using the Adit 600 with the CMG card talking
MGCP to asterisk? I want to have a central asterisk server with 10 Adit
600's at various locations providing 24 FXS ports....
Thanks,
Isaac
2005 Jan 28
1
adit 600 fxo ports immediately "answers" outgoing calls (even if not connected to line)
I have an adit 600 with an fxo card connected to a digium T1 card.
If I try to make an outgoing call and the T1 cable is disconnected,
asterisks returns congested like it should.
But, if the adit 600 is connected to the T1 card, the adit 600
immediately "answers" the call even if there are no physical
lines attached. I even removed the fxo card and the adit
600 still
2005 Mar 08
1
Adit 600 for asterisk
Ok, I've pretty much decided to try the Adit route. Somebody who has
experience with these tell me if I'm missing something.
I have 15 incoming PSTN lines. T1 is not an option at current
location. I want to put in an Adit 600 with 2 8-port FXO boards. The
adit will then connect to * via a digium t1 board. I configure
zaptel.conf for the T1. What other parts would be needed? How do
2006 Jun 03
2
ADIT 600 <=> Asterisk Help
I've been reading the Google searches trying to understand how to tie
together Adit 600 to Asterisk to provide 2 way service. I'm about blind
from reading.
I assume, the answer is using MGCP between the boxes. However, the examples
I found don't really explain fully enough to know how to modify examples to
work for me.
I'll have in the ADIT with T1's. There is a CMG and
2004 Dec 09
1
[OT] Adit 600 Question
Hi,
I'm using an Adit 600 Channel Bank with *. I love it and it works
really great for my FXS lines. One problem that I have with it (It's
really not a problem yet, but it's a potential one) is that I've
scoured the manaual for the Adit to see if there's a way to dump out a
config file from the bank so in the event of a power and battery
failure I don't have to type in the
2010 Jul 26
0
Adit 600 over MGCP.
Hi,
Anybody out there running Adit600s?
I have in my care an Adit600 channel bank connected to an old (version
1.0.6) Asterisk instance with MGCP. When trying a more recent Asterisk
(1.4.21.2~dfsg-3+lenny1, Stock current Debian) calls fail.
I have attempted to add the "slowsequence = yes" line to mgcp.conf. (It
seemed to be the only likely candidate in the example files I found
2007 Sep 03
1
ADIT 600 & CMG <=> Asterisk question
I've searched but can't find an answer as to how many MGCP paths can a
single ADIT/CMG card support? It appears it's only 24 ports, maybe 48.
What I'd like to do is install 6 Telco T1's into a single (or more) Adit
600 and route inbound calls towards asterisk. Can I have more than one
CMG in a single chassis?
Or maybe you know of a better way to connect T1's to
2004 May 18
2
ADIT 600 Manual
I am trying to find a manual for the Carrier Access Adit 600. Does anyone
know where I might be able to find one?
Thanks
-Jon
--
Jon J. Brandon jon@monsoonretail.com http://www.monsoonretail.com
2005 Feb 21
2
Adit 600 MGCP configuration
I've finally got my Adit 600 and are configuring it right now.
But I have to say, there aren't much documentation for it.
I've setup MGCP and Asterisk seems to find it.
But all channels (40 FXS channels) are "Down"!
But the MGCP itself is "Up" according to the statistics.
I can't find any documents how to set each channel to "Up" in the CLI.
Any
2005 Feb 12
1
PLEASE HELP Adit 600 went kaput?
After months of setting up Asterisk. I completed the
final testing last night We would go live on Monday.
Or so I thought.
As I moved the Adit 600 back out of the way, sliding
it six inches. I noticed the major light was red as
were both T1 and T2 lights ( eventhough only one t1
port is being used ) -- I have no idea what these
lights mean or if they were lit before when things
were working.
2004 Aug 24
3
Asterisk with Adit 600
Hello,
I am connecting Asterisk to an Adit 600 via a T100P. Unfortunately I am not able to get any lights on the T100P and the Adit 600 only shows red. I have already modprobed the t100p.
Has anyone successfully connected these before?
I've tried both a cross-over cable and a standard cat 5 cable, but I can't seem to get them to work.
Any suggestions?
Thanks!
Craig
2005 May 07
0
DTMF detection with Adit 600
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
It seems like Asterisk are having problems detecting DTMF digits when
using an Adit 600 channel bank via MGCP.
I've tried to turn on RFC 2833 on both Adit and Asterisk, but no
digits at all are working then.
Anyone experienced simular with Adit or other channel banks?
I'm also unable to use V.90 modem through my setup (Adit600 via MGCP
-
2009 Mar 03
2
Asterisk analog DID with Adit 600
Hello All,
I'm trying to connect Asterisk to an Executone phone system with an
analog DID card and I'm hoping someone can help me figure out what I'm
doing wrong. The Executone DID card provides battery to the telco, when
the telco wishes to dial a DID it goes off-hook, waits for a wink from
the Executone and then dials the last three digits on the number with
pulse (as opposed