Hi ! I am connecting to Adit 600 thru a T100P card I have configured 1-16 FXS channels and 17-24 FXO. Everything looks fine on Asterisk side I get a tone on all FXS channels, but when I try to dialout thru one of the FXO channels 17-24 it doesn't connect to the POTS line and echoes back my voice. I use fxsls and fxols for the T1 channels and ls on Adit side. Whats wrong here ? here is my Adit conf.... voip-pbx> print config --------------------------------------------------------- -Cactus.lite configuration file -Created on 01/01/1999 at 00:02:49 for adnan -This file is valid for the following configuration only: - - CardType - -------- -SLOT A T1x2 Code Revision: 1.3.1 -SLOT 1 FXSx8 -SLOT 2 FXSx8 -SLOT 3 FXSx8 -SLOT 4 FXSx8 -SLOT 5 FXOx8 -SLOT 6 FXSx8 - -Note: Lines beginning with '-' will be ignored as comme -by the CLI. Before downloading, review the sections of -configuration file delimited by these comments and delet -the commands that are not needed (e.g. 'set ip address' -and 'add user' are likely candidates for deletion). - -While downloading, a character and line delay of 5 ms is -recommended. --------------------------------------------------------- -Turning off verification messages. set verification off -Setting local off. set local off -Disconnecting all connections. disconnect a disconnect 1 disconnect 2 disconnect 3 disconnect 4 disconnect 5 disconnect 6 -Setting users. add user adnan -Setting network id. set id "voip-pbx" -Setting primary and secondary clock sources. set clock1 a:1 set clock2 internal -Setting IP addresses. set ethernet ip address 192.168.7.151 255.255.255.192 set ip gateway 0.0.0.0 -Setting the SNMP MIB-II System Group objects. set snmp getcom "public" set snmp setcom "public" set snmp trapcom "public" -Setting slot a. set a:1 up set a:1 fdl none set a:1 lbo 1 set a:1 framing esf set a:1 id "CAC DS1# 01" set a:1 linecode b8zs set a:1 loopdetect on set a:1 threshold min15 uas default set a:1 threshold min15 ses default set a:1 threshold min15 es default set a:1 threshold min15 sefs default set a:1 threshold min15 les default set a:1 threshold min15 css default set a:1 threshold min15 bes default set a:1 threshold min15 dm default set a:1 threshold min15 lcv default set a:1 threshold min15 pcv default set a:1 threshold day uas default set a:1 threshold day ses default set a:1 threshold day es default set a:1 threshold day sefs default set a:1 threshold day les default set a:1 threshold day css default set a:1 threshold day bes default set a:1 threshold day dm default set a:1 threshold day lcv default set a:1 threshold day pcv default set a:1:1-24 signal ls set a:1:1-24 type voice set a:2 down set a:2 fdl none set a:2 lbo 1 set a:2 framing esf set a:2 id "CAC DS1# 02" set a:2 linecode b8zs set a:2 loopdetect on set a:2 threshold min15 uas default set a:2 threshold min15 ses default set a:2 threshold min15 es default set a:2 threshold min15 sefs default set a:2 threshold min15 les default set a:2 threshold min15 css default set a:2 threshold min15 bes default set a:2 threshold min15 dm default set a:2 threshold min15 lcv default set a:2 threshold min15 pcv default set a:2 threshold day uas default set a:2 threshold day ses default set a:2 threshold day es default set a:2 threshold day sefs default set a:2 threshold day les default set a:2 threshold day css default set a:2 threshold day bes default set a:2 threshold day dm default set a:2 threshold day lcv default set a:2 threshold day pcv default set a:2:1-24 signal ls set a:2:1-24 type voice -Setting slot 1. set 1:1-8 signal ls set 1:1-8 txgain 0 set 1:1-8 rxgain 0 set 1:1-8 linelength short -Setting slot 2. set 2:1-8 signal ls set 2:1-8 txgain -3 set 2:1-8 rxgain -6 set 2:1-8 linelength short -Setting slot 3. set 3:1-8 signal ls set 3:1-8 txgain -3 set 3:1-8 rxgain -6 set 3:1-8 linelength short -Setting slot 4. set 4:1-8 signal ls set 4:1-8 txgain -3 set 4:1-8 rxgain -6 set 4:1-8 linelength short -Setting slot 5. set 5:1-8 signal ls set 5:1-8 txgain 0 set 5:1-8 rxgain 0 -Setting slot 6. set 6:1-8 signal ls set 6:1-8 txgain -3 set 6:1-8 rxgain -6 set 6:1-8 linelength short -Making connections. connect a:1:1-8 1:1-8 connect a:1:9-16 2:1-8 connect a:1:17-24 5:1-8 -Turning verification on.