similar to: TE410P not working

Hi anyone have a idea for debug my digium TE405P card ? My zaptel.conf: span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone = fr defaultzone = fr My Zapata.conf: [channels] language=fr context=from-E1 switchtype = euroisdn pridialplan = unknown signalling = pri_cpe usecallerid=yes hidecallerid=no callwaiting=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes

Hi, I am about to pull my hair out after trying to get our PRI up and working. We are switching from a Cisco gateway to an Asterisk box which provides the 23 phone lines for our office. So, because the Cisco gateway is working I can assume I have all the settings right (b8zs, esf, dms100, etc) and the PRI is live (because we are switching over). When dialing from PSTN, I get busy signal. When

Hi, I'm having problems with a TE420P card, in which I cannot make calls using spans 2 through 4. After a couple of days of working correctly, spans 2, 3 and 4 start failing (can not make calls). The system is configured to work with SS7. After the ACM message goes out, immediately a REL message is returned. I searched for error messages in /var/log/messages and could not find a clue

Hi I got the 2nd Gen firmware upgraded on the TE405P. I recompiled after putting in the upgraded board but did not change any conf, but the spans become active but will not come up. I guess I am missing something or are the any changes to the zaptel/libpri software that is required. I cannot find any info about this or does this new firmware only work with latest CVS. I am using 1.0.9 with

Hello I just updated the kernel, dahdi-linux and dahdi-tools Im also using now asterisk 1.4.26.1 And im still with a red light (not RED/YELLOW anymore): [root at catumbela ~]# /etc/rc.d/init.d/dahdi status ### Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" (MASTER) HDB3/ RED 1 PRI CAS RED 2 PRI CAS RED 3 PRI CAS RED 4 PRI

I'm using two Rhino channel banks (first 12FXO/12FXS, second 24FXS). These connect to a Digium TE210P card. I'm running kernel 2.6.10 and I've tried Asterisk (w/zaptel) 1.0.9, 1.2 beta, and CVS from today. The results are the same for all versions: Right after I reboot, and modprobe wct4xxp, my analog phone connected to port 13 of the first channel bank (first FXS port) gets a dial

TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and

Hi, I'm trying to connect a PC with a TE410P to an E1/IP equipment. Unfortunately I keep getting a yellow alarm from zaptel (in zttool) and a Loss of Framing alarm on the remote equipment. The E1/IP is connected on the other side to a PRI interface on a GSM MSC. I have configured the span as: span=1,1,0,ccs,hdb3 (also tried span=1,0,0,ccs,hdb3) and the channels as: bchan=1-15,17-31

I've seen this consistently on three systems, with three different cards, and multiple versions of DAHDI. At first I thought the issue only occurred on newer, Nehalem-based, systems, but I reproduced it on a Core 2 Duo box as well. I've tested with dahdi-linux 2.2.0.2, dadhi- linux-complete 2.0.0+2.0.0, 2.1.0.2+2.1.0.2, and 2.2.0.2+2.2.0. The card is a Digium TE220B which uses the

Dear members of the list, I have difficulties to obtain sync with a Digium TE420 PCI Express For four entries E1, In my case I am with only 3 E1s available to configure. The telephony operator is BrasilTelecom and Signaling is R2 Digital. The information I have is that are E1s with 32 channels, not have sure. My settings Have been based on the link reference:

Hello I've got small PBX (30 simultaneous connections) based on asterisk (1.6.2.6), which uses Stargate 2N ISDN to GSM gate. It runs ok for day or two, but then I get: dahdi: HDLC Receiver overrun on channel TE4/0/1/16 (master=TE4/0/1/16) in my kernel logs, in asterisk i get: pri show spans PRI span 1/0: Provisioned, Down, Active PRI span 3/0: Provisioned, In Alarm, Down, Active (span 3

I'm trying to connect an Asterisk T1 port to a Dialogic card. The Dialogic side is an external VMS. I setup for ISDN-PRI between systems and have green lights on both card/ports. Zttool shows connection is good also. However, when I try attempt terminate or originate a call to either system, nothing appears of CLI. How can I monitor the "D" channel? zaptel.conf: # Span 8:

Greetings, According to the FAQ "When you load the module and have no circuit/channel bank the LED's should flash red" I get the "knight rider" lights before the module loads, but after the modules are loaded I don't get any lights, other equipment plugged in or not. The card has been on my shelf a while so I wonder if it needs a firmware upgrade ? Can the cards

Has anyone had any success with the Rhino CB-24? I can't get mine to work, I tried all the obvious settings. The cb-24 gets stuck at init ESF framing, as if it's not seeing the t1 card at all. It does get a t1 carrier (detecting voltage??) Help! Thanks.. Everything appears to look good on the server, I did: [zaptel.conf] span=1,0,0,esf,b8zs fxogs=1-24 [zapata.conf] signalling=fxo_gs

Hello all, I'm using Wildcard TE410P card. Here is a zaptel.cfg loadzone=se defaultzone=se span=1,1,0,ccs,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 span=2,0,0,ccs,hdb3,crc4 bchan=32-46 dchan=47 bchan=48-62 span=3,0,0,ccs,hdb3,crc4 bchan=63-77 dchan=78 bchan=79-93 span=4,0,0,ccs,hdb3,crc4 bchan=94-108 dchan=109 bchan=110-124 # ztcfg -vvv Zaptel Configuration ====================== SPAN 1:

I'm a bit confused on how to setup Zaptel.conf and Zapata.conf when there is a TDM400P and a TE410P installed after upgrade. The TDM400P has 2 FXS in position 1 & 2 and 1 FXO in the fourth position. I see boot, WCT4xxP loading first and WCFXS loading second. According to my understanding, given above, the TE410P should be configured first, then the TDM400P. However, I'm not sure

I have a box with 12 T1s (4 Te410P cards). The PSTN provider is reporting slips and ask me to update the clock source. I have my system.conf set as the following but when I run dahdi_scan only the ports on Card 1 are showing up with syncsrc=1 system.conf : span=1,1,0,esf,b8zs bchan=2-24 mtp2=1 span=2,2,0,esf,b8zs bchan=26-48 mtp2=25 span=3,3,0,esf,b8zs bchan=49-72

Hi, after loading the zaptel driver wct4xxp I have strange log lines in the syslog: Out of storage space. free tells, that more than 900 MB are still free. Disk space is also available. I'm using a dual opteron in 64 bit mode. Any ideas? Roger. Syslog: Dec 1 02:18:37 ipphone4 kernel: TE410P: Launching card: 0 Dec 1 02:18:37 ipphone4 kernel: TE410P: Setting up global serial

Dear All, we have installed a TE410P card on a Dell Poweredge 1750 running a slackware 10 with 2.4.26 Kernel. Then we have made two loops on the card and we have configurated all the 120 channels. Our goals was to perform some stess tests even if in this scenario we used the same box as generator and target. The stress test comprised to generate up to 60 calls at the same time by placing a file

Hello, After installing on Ubuntu 10.04 using the tutorial on http://hmontoliu.blogspot.com/2010/03/installing-asterisk-and-freepbx-on.html I have a running instance of Asterisk. PROBLEM: result of dahdi_cfg: DAHDI Tools Version - 2.2.1 DAHDI Version: 2.2.1 Echo Canceller(s): MG2 Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Echo Canceler: mg2)