similar to: X100P Clone not picking up incoming calls. [POTS]

Thanks to everyone for your quick responses to this question. I'm very excited about the Asterisk project, and the growing community seems to be very active these days. Hopefully when the time comes for our county's transition to VoIP we may be able to go for an Asterisk-based solution. -- Tony Kava Network Administrator Pottawattamie County, Iowa -----Original Message----- From:

Hi. I have a x100p card installed on my asterisk box... my zapata.conf file includes the following lines: [channels] context=default switchtype=national signalling=fxo_ls rxwink=300 echocancel=yes rxgain=0.0 txgain=0.0 group=1 callgroup=1 pickupgroup=1 Basically, the zapata.conf file generated by make samples. Then in my extensions.conf I have this: [default] include => demo And demo is

Hi all, I'm planning to buy a X100P clone and would like some feedback about this card. Does anyone already used this card? Does anyone recommend it ? or not? I'd appreciate any comments. Thanks. Ronaldo.

Does anyone know if the X100P clone cards provide the timer needed to run MOH and the Conferencing service? I have no need for a T1 card, but I'm running asterisk on a dual processor machine with the wrong kind of USB devices, so none of the dummy timers will work for me. Also, I'm running Asterisk@Home (2.4 Kernel). Anyone know if upgrade to the 2.6 kernel will allow me to use the

Has anyone had any success with this card? Thank you. Sandy.

Hi, I'm trying to figure out why my Sweex CA000022 is not detected by wcfxo on my SuSE Pro 9.3 running on a VIA EPIA SP motherboard. The card should work as its an Intel 82537EP based card. When Booting the IRQ assignments for the board indicate: Bus Dev Func Vendor Dev Class 0 20 0 8086 1080 0703 lspci shows: 0000:00:14.0 Modem: Intel Corporation: Unknown device 1080

Hi.. I have one intel 536 EP. Does it possible use it as x100p clone for asterisk? I tried today with no luck :(.. Here is what I did : - plugged the card the card is recognised as (lspci -vv): 00:09.0 Communication controller: Intel Corp. 536EP Data Fax Modem Subsystem: Intel Corp.: Unknown device 1000 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-

install asterisk with x100p clone; the problem is that call me and hangup but the interface zap not detect the hangup and the line open. the error is : The 'reload' command is deprecated and will be removed in a future release. Please use 'module reload' instead. -- Reloading module 'chan_zap.so' (Zapata Telephony) == Parsing '/etc/asterisk/zapata.conf':

Now that the X100P is no longer being offered by Digium, what is the best solution? I seem to have run into a few posts where people talk about problems they've had with their X100P clone cards (dropping calls, echos, etc) other people seem to not have any problems. Of the three chipsets that will work: Intel 537EP, Ambient MD3200, and Motorola 62802 (as seen here

Hi, I have problem with X100P clone card.I can not force it to work under Asterisk 1.4.27.1 and DAHDI Version: 2.2.0.2. I looked over and over on configuration and could not see any mistakes. Here are relevant configuration files. /etc/dahdi/system.conf > fxsks=1 > echocanceller=mg2,1 > loadzone = hu > defaultzone = hu > dahdi_tool > OK Wildcard X100P

Hi All, Googling X100P Clone I found several information about these cards and seems that some winmodem has the same chip used from the original X100P. Here below a list winmodem which should work as X100P clone: 1057 Motorola 5608 SM56 PCI Fax Voice Modem E159 Tiger Jet Network Inc 0001 Tiger 300/320 PCI interface I bought one "Trust 56k V92 PCI Internal Modem MD-1100" which has the

Hi, can't get X100P (fully zapata compatible clone) to work (I'm in Australia). * recognises the card and the channel (1) but has definetely some problems talking to the pots line. I set up this simple dialplan for ZAP ("incoming" context, as setup in zapata.conf, for channel 1) [incoming] exten => s,1,Answer exten => s,2,Playback(somefile) exten =>

I am using 2 X100P clone cards in my asterisk system, and have one phone line plugged into the 'line' port of each card. On one of the cards, I also have a cable plugged into the 'phone' port and this cable is then connected to the modem on my PC so that I can use it for dial-up. I thought that this would then allow me to do dial-up and at the same time it would lock the port so

Hi, I had ordered a TDM40B and developers kit a few months ago. I have everything installed and working, with one exception - sound quality. When placing a call it sounds like a very bad cordless phone - lots of hiss / static in the background. This even happens with the dialtone, though it is much worse one the call is connected. This does not occur when the phone is directly connected to the

Greetings: I did some quick searching of my history of this list, and I tried a quick Google search as well, but perhaps someone on the list can quickly answer this question. I have a very nicely working Asterisk system at home with two Digium X100P FXO cards. When my SIP phones want to dial-out I have them setup to grab the first analog card (Zap/1) with the following extensions.conf segment:

Hi, I'm cutting my teeth setting up a home asterisk server, but having some trouble getting Zaptel to recognize a X100P clone PCI (Motorola SM56 which should work according to various wiki's). What struck me was that the "/proc/interrupts" do not include IRQ 11 as the "lpcpi -v" is reporting. Am I missing something fundamental here? Any hint is greatly

I'm new to asterisk and fror a cupple of days I heave been googleing the net for digium "clones", because it's very hard for me to get a digium card (X100P). Does anyone Know another substitute for X100P (I know that intel based modem with chip 537/MD3200 is working but I did not find any of those) ? I made it work with an Intel 536 (with a costumised driver that I found on

I can either get the TE100P working or the 3 X100P clones working, but never both. I have the TE100P connected to a channel bank, and X100P clones to lines from the phone company. This is my zaptel.conf span=1,1,0,d4,ami fxsks=1-24 loadzone=us fxols=25-27 loadzone=us I then do [root@asterix root]# modprobe zaptel [root@asterix root]# modprobe wcte11xp ZT_CHANCONFIG failed on channel

I'm not sure if I have a configuration problem or not. I am unable to dial out. When I try to dial in I can hear the phone ring on the dialling phone but Asterisk does not register anything. In zaptel.conf I have loadzone = au defaultzone=au fxsks=1 In zapata.conf language=au context=from-pstn When I do: zap show channels I get: Chan Extension Context Language

Okay, I'm going to preface this by saying I'm sure I've overlooked something really basic here. I just need someone to hit me with a clue stick and point out what I'm missing. I've got a TDM card with four FXO modules. I've plugged one of them into a PSTN line. I'm working through the examples in the Asterisk Documentation Project guide, but I can't get Asterisk