similar to: Polycom IP600 Presence question

I am currently utilizing Polycom IP600 phones and presense. I have placed the hint directives in and everything seems to work fine. But this only works for a short period of time. After about 30 minutes, the extensions do not see when others are on the phone. Has anyone seen this type of behavior before? I am currently utilizing v1.5.2 of the polycom software and the cvs-head release from

Have a strange problem... When a C7960 calls the Polycom ip600, the ip600's first line button blinks, the ip600 display shows the proper callerid, but the phone does not ring at all. If I call the same ip600 from a bt102, the ip600 rings properly. If I call the same ip600 from another C7960, the ip600 rings properly. All phones and asterisk are on the same lan within a few feet. The

Hi, I am mostly happy with my Polycom IP600 but it apparently needs to check the FTP server every minute. I couldn't find any obvious setting related to that behavior in the configuration files. Any idea how to curb the IP600's spurious network activity? Thanks, -- Lord, protect me from your followers.

Did you try to boot without lan just the power ... I've had this same problem to and rebooted the device without lan connection -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Louis-David Mitterrand Sent: woensdag 26 januari 2005 11:36 To: 'Asterisk Users Mailing List - Non-Commercial Discussion'

FYI for anyone using the dual ethernet ports on a Polycom IP600. I'm using a Polycom IP600 connected to an HP2524 10/100 switch, which has an asterisk box connected directly to it. No VLANs defined or in use. Measured bandwidth: PC -> HP Switch -> Asterisk : actual throughput measured at 94.1 mbps. PC -> IP600 -> HP Switch -> Asterisk : actual measured at 91.9 mbps. The

Passing this along. I got it tonight from a friend: Basis Technology has uncovered a potentially serious issue with the Polycom SoundPoint IP600 SIP phones, which causes them to spontaneously reboot at unpredictable times. It appears that if the amount of current being delivered to the phone falls below a certain threshold, the phone will reboot. Here are the specific circumstances which will

Hello, I have a polycom ip600 and eyebeam. When I call from polycom to eyeBeam, everything, including audio works. When I call the other side (from eyeBeam to polycom), I get no audio. In both cases, eyeBeam shows the same codec: g711u. Also sip show channels shows ulaw codec for both sides and correct addresses. I have canreinvite=no. I don't know if it's important, but asterisk

Hi all, I dont know why, but if I plug my PC inside the 'PC' slot on my polycom, this is not working. (Polycom IP600 is online on the net.) I'm using normal network cables. (I see jumpers behind the phone... do I need to play arround with that?) Any help would be appreciated. -- Alexandre Leclerc

Hi, I'm testing a Polycom IP600. With firmware version 1.1 the phone reboots at any time. With firmware version 1.2, the first reboot was an endless reboot. Then I moved the phone to another lan port, then it worked fine. Then I installed again in the initial lan port and the phone works well. However after some time of inactivity (1 hour?), the IP600 stops to send and receive calls.

Hello, I have configured my polycom ip600 and ip500. The phone works well. But the clock is wrong and flashes the whole time. Drives me nuts! I have set the time offset on the DHCP / boot server. 36000 (I'm in Australia!) It doesn't seem to help... Mike

I have been testing with Polycom IP600 phones for a month or so. I found out that there are frequent problems with the handset. The problem is I can hear the other end but the other end cannot hear me. I have already downloaded the latest bootROM 3.1.3 and sip 2.1.2 However, there are no problems with the headset or speaker phone. Has anyone encountered such problems before? Thanks.

Hi All, Can someone please advise me about configuring my Polycom IP600? I have an account with a SIP based IP Centrex provider. The basic SIP info and line 1 config points to them. That's working fine. I'd like to register line 2 with my own asterisk server. I've tried putting the basic registration info in the line 2 configs...but the phone never registers. Not certain how to

I'm having trouble with both my Polycom IP600 and IP500 disconnecting calls to the PSTN after about 1 hour. The below log is of a phone call that lasted 1hr 39mins which is my record so far. I cannot figure out what is causing the call to terminate and I am hoping somone on this list can help me. In this example both the phone and the asterisk server have public IP addresses so NAT shoul not

Hello list: I have a very odd problem. Seemingly randomly, my Polycom IP600 phones will ring without a call being placed to it. That is to say, a random phone will ring. Nothing shows up under Caller ID. Even the buttons that light up to show an incoming call do not light up. If you pick up the handset, you can hear the phone ring through the speaker. Hanging up the phone makes it stop

Just wondering if anyone has gotten instant messaging working between two polycom phones/and or MSN messenger with asterisk in the middle? I tried a few things but couldn't get it to work... Regards, Adam

Hello, I faithfully followed the instructions from: http://www.voip-info.org/wiki-Getting+MWI+on+Polycom+Phones+to+work+with+Asterisk but still the message waiting indicator doesn't flash when a message is waiting. There is a brief intermittent chirp but nothing more. Using latest firmware 1.4.1 Thanks for your suggestions,

Hello, I am looking at the Polycom phones. The ip600 has a very nice screen, is that the only real advantage over the ip500 and ip300.. Is it worth the extra dollars? Kind regards Michael Felder IT Medic Australia Pty. Ltd. P: 03 9557 2213 F: 03 9557 2214 M: 0419 568 217 E: Michael@ITMedic.com.au <blocked::mailto:Michael@ITMedic.com.au> http://www.ITMedic.com.au

This Polycom phone seems to be one of the best on the market for sound quality and features. I have seen on the list that some people have gotten the IP 600 to work with Asterisk. Does anyone have the details of how to get this working i.e. XML phone config files, and any thing else I might need to know. Thank You, Chad Cowan -------------- next part -------------- An HTML attachment

Hello All, I am wondering if there is a way to make Polycom IP 500 SIP phone display digits dialed after a call is connected. For example, when I call an IVR, after the connection is complete, the digits dialed to enter account number etc are not displayed on the phone. They are sent to the target. My users are asking to see the digits dialed as they are used to seeing them on our old Nortel

Hello, After checking out CVS HEAD from yesterday (for those new PLC/Jitterbuffer patches), I was affected by bug 3795 with my Polycom IP600's. After seing it resolved as of this morning (thanks Mark), I decided to try again... I can answer incoming calls. No problem there. Putting calls on hold, however, results in my Polycom IP600 indicating the call on hold, but the caller does