similar to: McLeod Integrated T1 - no PRI?

Hello, I'm just starting out with asterisk and I'm playing around with the system. Currently I have a Digium TE210P connected to a PRI on the Asterisk server. I have a SIP soft phone on my laptop for testing that is working fine. When I try to place a call from my soft phone I get this from Asterisk: May 1 09:11:41 NOTICE[20098]: app_dial.c:1029 dial_exec_full: Unable to create

hello, i installed an asterisk as a pri gateway. Everything is okay. /etc/init.d/zaptel starts successfull with wct4xxp module. /etc/init.d/asterisk starts also successfully. I tested my pri cable and it works. But still my span isn't up. I don't see any error. Do you have any idea? What else i should check? Thanks. My card is 4 span Wildcard TE410P

Hi Guys, Anyone might know why this error keeps showing up and inbound/outbound is not working on a Bell PRI with Sangoma A101D? -- Got SABME from network peer. Sending Unnumbered Acknowledgement No calls can be made inbound/outbound. Keeps repeating. No alarms ON and no changes been made to the system. Stopped all a sudden. Asterisk CLI doesn't show anything with full verbose for both

Hi, I have debian etch 4.0 machine (2.6.18) with two TW-ISDN PCI (Hfc) cards. I use bristuff-0.3.0-PRE-1y-e (asterisk-1.2.17,libpri-1.2.4,zaptel-1.2.16). I also have patched zaphfc with zaphfc_0.4.0-test1_florz-13.diff.gz (I load module: insmod /usr/src/bristuff-0.3.0-PRE-1y-e/zaphfc/zaphfc.ko modes=1 debug=1). So i want to test two cards and make loop between them. So one card would be NT,

We have a server with a TE120 on a partial PRI trunk that several times a day declares the PRI trunk down and stops handling calls until the asterisk is stopped, the zaptel/te120 modules reloaded, and asterisk started. Just before things go down, the log shows the following error: ERROR[9424] chan_zap.c: Write to 28 failed: Unknown error 500 at which point a "show pri spans"

Hello. I have a TE212 configured in E1 mode. This is shown in a cat /proc/zaptel/2 and 3 (where the card is configured): cat /proc/zaptel/2 Span 2: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" HDB3/CCS/CRC4 RED NOTOPEN 25 TE2/0/1/1 Clear 26 TE2/0/1/2 Clear 27 TE2/0/1/3 Clear 28 TE2/0/1/4 Clear 29 TE2/0/1/5 Clear 30 TE2/0/1/6 Clear

Hi all, My problem boils down to these errors: ... Unable to create channel of type 'ZAP' (cause 34 - Circuit/channel congestion) == Everyone is busy/congested at this time This is triggered by lines in extentions.conf such as: exten => _X.,1,Dial(ZAP/g1/${EXTEN},,W) The system is CentOS v5.2 with Asterisk 1.4.23 (druid-asterisk-1.4.23.1-2), a Sangoma A104

Hello, I have following problem with Sangoma A104 card: CLI> pri show span 1 Primary D-channel: 16 Status: Provisioned, Down, Active Switchtype: EuroISDN Type: CPE Window Length: 0/7 Sentrej: 0 SolicitFbit: 0 Retrans: 0 Busy: 0 Overlap Dial: 0 T200 Timer: 1000 T203 Timer: 10000 T305 Timer: 30000 T308 Timer: 4000 T313 Timer: 4000 N200 Counter: 3 NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI

Hi list! I'm trying to setup Digium TE205P E1 card to work with my provider (and Ericsson BP 250 - this comes later). When I execute "pri show span 1" this is what I get. pbxzg1*CLI> zap show status Description Alarms IRQ bpviol CRC4 T2XXP (PCI) Card 0 Span 1 OK 0 0 0 T2XXP (PCI) Card 0 Span 2 UNCONFIGUR 0 0 0 pbxzg1*CLI> pri show span 1 Primary D-channel: 16 Status:

Is anybody else using the following combination: * a TE410P card (wct4xxp driver) * a BT ISDN connection * DAHDI 2.3.0.1 * Asterisk 1.6.2.9 I'm trying to configure a new box to replace a legacy system (same hardware; some old version of Asterisk with Zaptel; works lovely but hopelessly out-of-date) and not having much joy. Specifically, I couldn't get it to see a D-channel on

I have a server running Asterisk 1.4.14, Zaptel 1.4.6, Libpri-1.4.2 on a CentOS 5 server. The server has a single TE110 card connected to a provider called Alestra in Monterrey, Mexico. Since we installed everything we have been having problems dialing certain numbers, those numbers always fail when dialed from Asterisk but if you dial from your cell phone they always go through. I once has a

Hello, I wrote earlier today about a new PRI installation in the Caribbean, where all outbound calls are functioning fine *except* calls to Sprint phone numbers, which get rejected immediately as "busy". The telco has been working with their switch manufacturer and took the output of "pri show span 1" from me and came back with this: ----quote--- Please check your timers

I've got a system with 5 pri circuits configured into a CFAS group with a primary and secondary d channel. There are three TE410P cards in the system. The 5 circuit span are located as follows: circuit 1 on span 5 circuit 2 on span 1 circuit 3 on span 6 circuit 4 on span 2 circuit 5 on span 9 primary d chan is on chan 24 of span 5 (chan 120) secondary d chan is on chan 24 of span 1 (chan

Hi all, I'm having some problems getting TDMoE setup for the 1st time. I have a TE405P installed in the main server with an ethernet cross-connection to the secondary machine. (Yes, I know about IAX2 but I want to use TDMoE to simulate using T1s.) I'm using -HEAD from yesterday. On the main machine /etc/zaptel.conf: loadzone = us defaultzone=us

Hello all Asterisk 1.2.10 BRIstuff PRE-1s Debian sarge I have an issue with my ISDN-BRI line. Asterisk tells me my D-Channel is down, no matter is I have an actual line plugged in or not. == Primary D-Channel on span 1 down I somehow got it to work once! The config tools do not indicate any errors whatsoever. Here is a rundown of various listings I can think about. (some things may show

Hi all, as good? I am trying to go up a board TE110P with link E1 ISDN PRI to establish connection with a central office Siemens HiPath 4000. But I am having the following errors: Server1:~ # asterisk -r Asterisk 1.2.10, Copyright (C) 1999 - 2006 Digium, Inc. and others. Created by Mark Spencer <markster@digium.com> Asterisk comes with ABSOLUTELY NO WARRANTY; type 'show warranty'

Hello, I am having odd issues with a new PRI based installation. Outbound calls work for all numbers except those that terminate at Sprint! The telco is new to PRI (this is in the Caribbean) and say that Sprint is rejecting the calls, and asked for our PRI settings so they can work with their switch manufacturer. We are using the bare minimum default settings, but I can imagine that a

Hi everyone, I am reading through Sangoma Wiki right now. But someone may already and quickly notice this. I have a system that is down since the morning (maybe power intruptions). All seems fine except for "wanrouter status" shows disconnected. Following are the alarms raised. Should I call telco (they have long wait times) or should I just keep searching online for troubleshooting

Hi, We recently got a PRI installed at one of our local centres however, we appear to be having interesting issues. Everything seems to be installed in the correct manner. asterisk*CLI> pri show span 1 Primary D-channel: 16 Status: Provisioned, Down, Active Switchtype: EuroISDN Type: CPE Window Length: 0/7 Sentrej: 0 SolicitFbit: 0 Retrans: 0 Busy: 0 Overlap Dial: 0 T200 Timer: 1000 T203

Hi, I've a busy server where one E1/PRI span has been behaving oddly. Here's the span: Primary D-channel: 16 Status: Provisioned, Up, Active Switchtype: EuroISDN Type: CPE Window Length: 0/7 Sentrej: 0 SolicitFbit: 0 Retrans: 0 Busy: 0 Overlap Dial: 0 T200 Timer: 1000 T203 Timer: 10000 T305 Timer: 30000 T308 Timer: 4000 T313 Timer: 4000 N200 Counter: 3 Looks good, eh? But every