similar to: TxFax: can't get a fax to destination (log inside)

I've been using spandsp and rxfax to receive faxes for a while now and over the past few days I've looked into the other side of things - txfax. I can't seem to get it working properly. I've included debug logs below of both the tx and rx side of things. I've tried three different servers, asterisk v1.0.6, 1.0.9 and CVS, FC2 and FC4, libtiff 3.5.7 and 3.7.1, TE405P and

Hello folks! I'm trying yo set up a email2fax and fax2email on my asterisk box. The rxfax works fine in my setup. The problem is with the txfax. I have tryed all snadsp version (0.0.2x and 0.0.3x) but I get this errors. Because I can't find anything on Internet I'm hoping u can give me a hand. here are my logs: -- Attempting call on SIP/sip_provider/1234 for application

Hi all, I'm using txfax and rxfax to send and receive faxes. I find that txfax performs very well when sending to an old fax machine. However, when trying to send to a Mac (OS X) that accepts faxes, I get a "Trainability test failed" message on the * console (full console log below). I'm OK with being unable to fax to Mac, as I'm just using it to test. For future

I'm getting the following when sending to a specific fax machine. Any ideas? File name is '/var/spool/asterisk/email2fax/7F2SOeYJiU.tif' Changed from phase 0 to 2 Slow carrier up Slow carrier down Slow carrier up <<< NSF: 20 00 00 11 80 00 8a 49 10 53 54 49 52 4c 49 4e 47 20 43 4f 56 49 4e 47 54 00 67 00 80 80 80 0c 01 02 NSF without final frame tag The remote is made by

Hi, I'm trying to send a fax from a Zap channel to another Zap channel and I can't - below the logs. How could I solve this? Thanks! In RECEIVER: -- Accepting call from '' to '1980' on channel 0/2, span 1 Urgent handler -- Executing Answer("Zap/2-1", "") in new stack Urgent handler Urgent handler -- Executing Goto("Zap/2-1",

Guys, I have been a trying to send a fax using spandsp/app_rtxfax/asterisk. I'm trying to send a (3 page) fax, and all I'm receiving is a single blank page (and I've tried it with 2 fax machines). As some background, I'm using asterisk with an E1 connection through a Sangoma WAN card -- all of this has been working with voice for over 6 months. The software is all working too

Guys, [Forgive this repost -- my original posting doesn't seem to have shown up in the list (yet)] I have been trying to send a fax using spandsp/app_rtxfax/asterisk. I'm trying to send a (3 page) fax, and all I'm receiving is a single blank page (and I've tried it with 2 fax machines). As some background, I'm using asterisk with an E1 connection through a Sangoma WAN card

Hello, I tryed out spandsp with libtiff-3.5.7 and with Asterisk from CVS. I tryed to receive a fax on a CAPI channel. Finally I got a file with 8 byte length (/tmp/testfax.tif). How can I do next? Thanks in advance, Thomas ps: what are hardware requirements for sending/receiving faxes? -- creating pipe for PLCI=0x101 msn = 2258589 > sent ALERT_REQ PLCI = 0x101 --

more detailed output Sep 21 15:54:31 DEBUG[1120357296]: pbx.c:1255 pbx_extension_helper: Launching 'RxFAX' Sep 21 15:54:31 DEBUG[1120357296]: channel.c:1699 ast_set_read_format: Set channel Zap/1-1 to read format SLINR Sep 21 15:54:31 DEBUG[1120357296]: channel.c:1666 ast_set_write_format: Set channel Zap/1-1 to write format SLINR Changed from phase 0 to 1 Slow carrier up Slow carrier

Hi list, Just installed spandsp. In my limiting testing, I have an issue on a Philips fax machine (HFC21) directly connected to my * server through TDM400, reception with rxfax works fine, but txfax always fails. Below is a transcript of failed transmit. This is with asterisk-1.0.3 (with native moh patch but I don't think it is the source of the problem). I already tried libtiff 3.5.7,

Hi, I am trying to recice a fax with * using SpanDSP - but it doesn't create the output file. (See the bottom of log file). * Loads both app_rxfax.so and app_txfax.so fine. Also I can't make * autodetect an incomming fax call (yes I have enabled faxdetect=both in zapata.conf - though it's not a Zap device) Any ideas are welcome :-) Best Regards Michael L?jtnant System Details:

Hi, I have tried to install and configure the FAX app using the steps described in several mails on this list. When a FAX call arrives on X100P, the fax extension is executed, which looks like: exten => fax,1,RxFax(/var/spool/asterisk/incoming/${CALLERIDNUM}.tif) exten => fax,2,Hangup It tries to negociate, but nothing is received at the end and the other part times out. More, after this

Hi, so far I had our PRI line connected via Digium TE410P and ZAP channel to asterisk which worked perfectly. I now have a second line coming in through a H.323 gateway and chan_oh323. rxfax() still works and receives faxes with G.711 alaw codec, but I always get one empty first page via H.323 - a one-page-fax becomes a two-page-fax with one empty page in front of it. It seems the empty page

I've seen people mention that they have fax reception working with Asterisk, spandsp, and app_rxfax. I'm using the latest Asterisk from CVS, SpanDSP 0.0.1k, and the latest app_rxfax.c (as mirrored by friendly list members recently), and libtiff 3.5.7. Asterisk is detecting the fax signal properly, and executing the fax extension in the dialplan. The fax part of the dialplan is pretty

Hi, I am trying to receive a fax with the spandsp library. The sending fax says "success" but there is no tiff file generated. I use "exten => 7000,1,rxfax(/tmp/testfax.tif)" in my extensions.conf. The connection is via SIP/G.711 as I have read on the list that this can sometimes work (I know Fax over IP is troublesome without T.38). I think the transmission should not

I use http://www.voip-info.org/wiki-Asterisk+callingcard You only should compile the prepaid.c (look at readme file). Regards. Julio ----- Original Message ----- From: <clive18@webmail.co.za> To: <juliom@telelinkusa.net> Sent: Tuesday, April 20, 2004 12:47 AM Subject: fwd:Re: [Asterisk-Users] Asterisk prepaid debug > Hi > > Which pre-paid app are you using?. > Is it

Initial handshake sounds fine, but asterisks dies before receive of the fax. Here is the log : Changed from phase 0 to 1 Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow

Sorry to bore you more with the clock issue, but have you check /proc/zaptel/<span> to make sure it's not missing interrupts? There's also an option to record the audio for the fax, you could listen to that vs a recorded file that will receive correctly on a fax machine and see whether there is an obvious difference? (Good luck, that'll be really scraping the barrel!!) Does it

I'm trying to install the RxFax in Asterisk. After much trouble getting app_rxfax.c (and friends) compiles and installed into Asterisk (thanks to the many asterisk-users messages) it did get it installed. I have been unable to receive a legible fax. app_rxfax provides lots of debugging information but none useful to me. I was hoping that someone has an idea what might be going on.

Hi all, Trying to get fax reception going using a voicetronix openline4 card, however, there are two issues (as far as I can see) (1) Currently the voicetronix world (cards, firmware, drivers, channel prog etc.) does not do fax tone detection. I have spoken to the voicetronix guys , understand what has to happen there and may do some hacking if I can resolve the second issue. Meanwhile, I