similar to: te410p not working after cvs-head update

Greetings, According to the FAQ "When you load the module and have no circuit/channel bank the LED's should flash red" I get the "knight rider" lights before the module loads, but after the modules are loaded I don't get any lights, other equipment plugged in or not. The card has been on my shelf a while so I wonder if it needs a firmware upgrade ? Can the cards

Hi to all out there using HP DL380 G4 servers, i found a way to get the Digium TE410P with older firmware running on a HP-Compaq DL380 G4 Server! Here's the step-by-step description: 1. download the latest BIOS (in my case it was 4.04 from date: 06/02/2005) for the HP-Compaq DL380 G4 using the "Systems ROMPaq Firmware Upgrade Diskette for HP ProLiant DL480 G4 (P51) Servers" Link:

List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to

I successfully installed asterisk@home 0.6, but when i try to load the wct4xxp module for the TE405P I just got, I get the following: Found TE410P at base address fb7ffc00, remapped to e0220c00 TE410P version c01a009b Tried to load 1c8ac800 into 00000000, but got 188ac800 instead Tried to load 1c8ac000 into 00000001, but got 188ac000 instead Tried to load 07fc07fc into 00000002, but got 03fc07fc

Hi list, After a lot of testing + troubleshooting, I guess I'm observing what I am now calling a regression with zaptel 1.4.10 (is it?) As such I call for peer feedback, before either asking Digium install support or filing a bug. Thanks in advance! System: HP Proliant DL380 G5 with 2x PCI-X + 1x PCIe riser card OS: Centos 5 Kernel: 2.6.18-53.1.14.el5 (also tested under

Hi to all, I have a problem with this wildcard and one E1 line. The server is a Asus P4P800S with the 865PE chipset, and 512MB RAM. The kernel version is 2.4.26. I have donwload and build the latest CVS version of zaptel, libpri and asterisk following the ufficial instructions of digium. I have set up my server in this way: zaptel.conf loadzone=it defaultzone=it

hi, I'm trying to configure my newly acquired TE410P card to work as 4 E1 spans. This is supposed to be a drop-in replacement to the earlier E100P card. However, on loading the zaptel module it gets configured as T1 spans basically doing a 'cat' on /proc/zaptel/1 thru 4, it shows 24 channels per span. After this ztcfg fails saying 'ZT_CHANCONFIG failed for channel 97'.

I'm installing TE405P card. This is my zaptel.conf. -------------------------------------- span=1,0,0,ccs,hdb3,crc4 span=2,1,0,ccs,hdb3,crc4 span=3,0,0,ccs,hdb3,crc4 span=4,0,0,ccs,hdb3,crc4 loadzone = us defaultzone= us -------------------------------------- When i modprobe wct4xxp, -------------------------------------- PCI: Found IRQ 11 for device 02:0b.0 PCI: Sharing IRQ 11 with

I'm trying to install a TE410P this is what happens with compiled zaptel 1.0.9, 1.2-beta and 1.0.9 from http://updates.xorcom.com/iso/ this is my zaptel.conf (checked with the provider the values): span=1,1,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 loadzone=it defaultzone=it then I modprobe wct4xxp debug=1 t1e1override=15 and the kernel says : Sep 30 16:12:40 localhost kernel: Zapata

I have a T1 PRI from the telco and have been trying to get it to work with the wildcard T400P. I know framing and coding is esf and b8zs. what else should I be putting into the zaptel.conf and zapata.conf. Dave Anderson

hi guys, do you have any suggestions on how to connect 2 TE410P via E1? (for simulation and testing purposes) asterisk1 --> TE410P ----> ? ---------> ? ---->TE410P -->asterisk2 -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030907/698cd499/attachment.htm

Hi list, We have been trying to configure a Quad Span T1 card in a system running RH9. We have followed the instructions in the Wiki and searched the mailing lists, but so far havent got any success. Cable is connected to the first span, and module is loaded. Without loading the module the LED glows in red colour, but the moment we load module, it goes off. (No red or green) . We ran zttool

Max TE410P card on an Asterisk Hello, Does anybody know the max number of TE410P/TE405P card we can put in an asterisk box? Thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040504/f220d3ae/attachment.htm

Hi, I found E400P quad PRI card quite cheap (749USD): http://www.govarion.com/product_info.php?cPath=1&products_id=2&osCsid=68cdd6e3d08754 in comparison to te410p (approx 1500 USD ) http://www.digium.com/index.php?menu=product_detail&category=hardware&product=TE410P Now newer generation with HW echo canceling emerged (te411p). I'm not sure in what things those two cards

I anyone has any hesitations in upgrading their 405P (or 410P) to V2 of the firmware, read below; I installed one today (turnaround time around 2 weeks to Australia, inc. economy freight in both directions... impressive!) and have noticed immediate, significant improvements. Audio levels are better (have set tx and rx gains back to 0.0) and missed frames have gone (popping, clicking,

for today we only have experience with BRI applications together with asterisk. is the following scenario possible and stable enough for production? FYI : We want to build a unified messaging application integrated with SIP. We have an E1 connection in Belgium with 100 msn's We would think about having 2 servers : Server A : Asterisk PRI card (Digium TE410P) Server B : Fax

TE410P - one way audio, after "rpm -qa" on RedHat 9 After much trouble, I can consistently reproduce this error. Anyone have any idea why all Zap channels on my TE410P would develop one way audio after "rpm -qa" has been run while asterisk is running? If I reboot, run "rpm -qa" first then load asterisk and modules all is OK when "rpm -qa" runs the second

Has anyone else experienced a problem with the LED for span 1 on a TE410P or TE405P? I had a TE410P on which the span 1 LED would not light red, but once the span was connected, it did correctly light green. I RMAed the board to our UK distrbutor and received a replacement. However, the replacement board displayed the same problem! Wondering if it was related to the computer I was putting it

TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and

Was there any resolution on this I also have a TE410P in an box with an Intel E7501 chipset? -Vickers -------- Original Message -------- Subject: RE: [Asterisk-Users] Re: TE410P card in an HP-Compaq DL380 G4 server Date: Tue, 8 Feb 2005 11:13:24 +1030 From: Peter Childs <peter.childs@nec.com.au> Reply-To: Asterisk Users Mailing List - Non-Commercial Discussion