similar to: All channels on PRI stuck "Resetting"

I've got a system with 5 pri circuits configured into a CFAS group with a primary and secondary d channel. There are three TE410P cards in the system. The 5 circuit span are located as follows: circuit 1 on span 5 circuit 2 on span 1 circuit 3 on span 6 circuit 4 on span 2 circuit 5 on span 9 primary d chan is on chan 24 of span 5 (chan 120) secondary d chan is on chan 24 of span 1 (chan

Hi all, I'm having some problems getting TDMoE setup for the 1st time. I have a TE405P installed in the main server with an ethernet cross-connection to the secondary machine. (Yes, I know about IAX2 but I want to use TDMoE to simulate using T1s.) I'm using -HEAD from yesterday. On the main machine /etc/zaptel.conf: loadzone = us defaultzone=us

Hello all Asterisk 1.2.10 BRIstuff PRE-1s Debian sarge I have an issue with my ISDN-BRI line. Asterisk tells me my D-Channel is down, no matter is I have an actual line plugged in or not. == Primary D-Channel on span 1 down I somehow got it to work once! The config tools do not indicate any errors whatsoever. Here is a rundown of various listings I can think about. (some things may show

hello, i installed an asterisk as a pri gateway. Everything is okay. /etc/init.d/zaptel starts successfull with wct4xxp module. /etc/init.d/asterisk starts also successfully. I tested my pri cable and it works. But still my span isn't up. I don't see any error. Do you have any idea? What else i should check? Thanks. My card is 4 span Wildcard TE410P

Hi Guys, Anyone might know why this error keeps showing up and inbound/outbound is not working on a Bell PRI with Sangoma A101D? -- Got SABME from network peer. Sending Unnumbered Acknowledgement No calls can be made inbound/outbound. Keeps repeating. No alarms ON and no changes been made to the system. Stopped all a sudden. Asterisk CLI doesn't show anything with full verbose for both

We have a server with a TE120 on a partial PRI trunk that several times a day declares the PRI trunk down and stops handling calls until the asterisk is stopped, the zaptel/te120 modules reloaded, and asterisk started. Just before things go down, the log shows the following error: ERROR[9424] chan_zap.c: Write to 28 failed: Unknown error 500 at which point a "show pri spans"

Hello. I have a TE212 configured in E1 mode. This is shown in a cat /proc/zaptel/2 and 3 (where the card is configured): cat /proc/zaptel/2 Span 2: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" HDB3/CCS/CRC4 RED NOTOPEN 25 TE2/0/1/1 Clear 26 TE2/0/1/2 Clear 27 TE2/0/1/3 Clear 28 TE2/0/1/4 Clear 29 TE2/0/1/5 Clear 30 TE2/0/1/6 Clear

Hello everyone, We have recently turned up a new T1 from McLeod (Midwestern CLEC). It is configured like so: /etc/zaptel.conf: loadzone=us defaultzone=us span=1,0,0,esf,b8zs ;(also tried 1,1,0,esf,b8zs) bchan=13-23 nethdlc=1-12 dchan=24 /etc/zapata.conf: switchtype=national context=pri-in signalling=pri_cpe group=1 channel => 13-23 I can get hdlc0 (and pvc0) up just fine after the

Hi everyone, I am reading through Sangoma Wiki right now. But someone may already and quickly notice this. I have a system that is down since the morning (maybe power intruptions). All seems fine except for "wanrouter status" shows disconnected. Following are the alarms raised. Should I call telco (they have long wait times) or should I just keep searching online for troubleshooting

Hi, We recently got a PRI installed at one of our local centres however, we appear to be having interesting issues. Everything seems to be installed in the correct manner. asterisk*CLI> pri show span 1 Primary D-channel: 16 Status: Provisioned, Down, Active Switchtype: EuroISDN Type: CPE Window Length: 0/7 Sentrej: 0 SolicitFbit: 0 Retrans: 0 Busy: 0 Overlap Dial: 0 T200 Timer: 1000 T203

Hello asterisk-users, I have problem with E1 line between Asterisk computer and our PBX Matra: asta*CLI> pri show span 1 Primary D-channel: 16 Status: Provisioned, Down, Active Switchtype: EuroISDN Type: CPE Window Length: 0/7 Sentrej: 0 SolicitFbit: 0 Retrans: 0 Busy: 0 Overlap Dial: 0 T200 Timer: 1000 T203 Timer: 10000 T305 Timer: 30000 T308 Timer: 4000 T313 Timer: 4000 N200 Counter: 3 My

Hi, I've connected Asterisk with 4 PRI to a Siemens HiPath 4000. For CALLERID(name) feature I wanna use Q.SIG as switchtype. Cause Siemens PBX orders Channels logical I need the parameter qsigchannelmapping=logical. Here is my chan_dahdi.conf trunkgroups] [channels] language=de context=default usecallerid=yes hidecallerid=no callwaiting=yes usecallingpres=yes callwaitingcallerid=yes

Hi list! I'm trying to setup Digium TE205P E1 card to work with my provider (and Ericsson BP 250 - this comes later). When I execute "pri show span 1" this is what I get. pbxzg1*CLI> zap show status Description Alarms IRQ bpviol CRC4 T2XXP (PCI) Card 0 Span 1 OK 0 0 0 T2XXP (PCI) Card 0 Span 2 UNCONFIGUR 0 0 0 pbxzg1*CLI> pri show span 1 Primary D-channel: 16 Status:

Hi Guys I'm configuring a TE212P card and have the following two entries in my /etc/asterisk/zapata.conf switchtype=dms100 signalling=pri_cpe When I reload asterisk I get the following messages: > -- Reloading module 'chan_zap.so' (Zapata Telephony) > == Parsing '/etc/asterisk/zapata.conf': Found > [Mar 30 17:48:42] WARNING[2985]: chan_zap.c:11072

In the process of turning up a new pri. Zttool indicates the T1 is ready with no alarms. asterisk*CLI> pri show span 1 Primary D-channel: 24 Status: Provisioned, Down, Active Switchtype: National ISDN Type: CPE Window Length: 0/7 Sentrej: 0 SolicitFbit: 0 Retrans: 0 Busy: 0 Overlap Dial: 0 T200 Timer: 1000 T203 Timer: 10000 T305 Timer: 30000 T308 Timer: 4000 T313 Timer: 4000 N200 Counter: 3

Hi there I have a TE110P card fitted in my linux box running : Linux version 2.6.9-5.ELsmp (bhcompile@decompose.build.redhat.com) (gcc version 3.4.3 20041212 (Red Hat 3.4.3-9.EL4)) #1 SMP Wed Jan 5 19:30:39 EST 2005 I followed the installation steps on digium website...no errors reported. The modules seem to have loaded...here's what lsmod shows: Module Size Used by

Hi all, My problem boils down to these errors: ... Unable to create channel of type 'ZAP' (cause 34 - Circuit/channel congestion) == Everyone is busy/congested at this time This is triggered by lines in extentions.conf such as: exten => _X.,1,Dial(ZAP/g1/${EXTEN},,W) The system is CentOS v5.2 with Asterisk 1.4.23 (druid-asterisk-1.4.23.1-2), a Sangoma A104

Hello, I have following problem with Sangoma A104 card: CLI> pri show span 1 Primary D-channel: 16 Status: Provisioned, Down, Active Switchtype: EuroISDN Type: CPE Window Length: 0/7 Sentrej: 0 SolicitFbit: 0 Retrans: 0 Busy: 0 Overlap Dial: 0 T200 Timer: 1000 T203 Timer: 10000 T305 Timer: 30000 T308 Timer: 4000 T313 Timer: 4000 N200 Counter: 3 NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI

I have a server running Asterisk 1.4.14, Zaptel 1.4.6, Libpri-1.4.2 on a CentOS 5 server. The server has a single TE110 card connected to a provider called Alestra in Monterrey, Mexico. Since we installed everything we have been having problems dialing certain numbers, those numbers always fail when dialed from Asterisk but if you dial from your cell phone they always go through. I once has a

Hi List, I have configured TE121PF card in E1 mode. I am using asterisk 1.6 and freepbx 2.7. My card staus turn in to green and looks like sync with the service provider. My service provider is BSNL - India. I have one toll free number for incoming and one land line number for out going calls. Problem : If i am calling to the toll free number, i am getting the ring but that call is