similar to: Echo Madness

I have a small system based on one TDM400 card with - 2 FXO modules for incoming lines - 1 FXS module for one phone The system was working fine in the past. The motherboard was exchanged and during the switch, the phones line was rewired with a mistake and a incoming phone line was connected to the FXS module, and there was ringing voltage on the module. Now, the system kinda works but the FXS

I have read thru what other users have tried in this list when they have experienced seemingly similar issues to what I have, without success. I suspect there might be an issue regarding both the X100P and TDM04b cards being used in an Intel SE7525GP2 motherboard, as I had to even wait for a BIOS update from Intel in order to utilize my 3ware 9500 SATA raid controller on it (3ware Kb -->

Hi, I am struggling to get rid of a conflict on DELL 2800 : PCI Parity error (EB113 on the display) I am learning linux and asterisk as I go along, there might be obvious things I should know, but bear with me. >From demsg below my 2 digium cards installed are listed (no config or connections done to digium cards yet), the conflict is with the TDM400P card, without that card, in any slot, no

Hi, I have a TDM400P running with only one FXO port running on a VIA EPIA MS10000 (1Ghz Via Eden). When I run zttest from Zaptel 1.2.1 it hang and when I interrupt it with Ctrl-C that is the result: ?anyone have some idea about why isn't working? Some additional info: # /usr/src/zaptel/zttest -v Opened pseudo zap interface, measuring accuracy... --- Results after 0 passes --- Best:

I just installed an FXS module onto a 4 channel tdm thats about 5 years old and it wont work. Running dmesg I can see the following error: Zapata Telephony Interface Registered on major 196 Freshmaker version: 71 Freshmaker passed register test !!!!!!! LOOP_CLOSE_TRES iREG 1C = 1 should be 1000 !!!!!!! RING_TRIP_TRES iREG 1D = 8000 should be 3600 !!!!!!! COMMON_MIN_TRES iREG 1E = 0 should

I am having trouble with chan_zap.so not loading. When I load it from modules.conf, Asterisk bails out without any error message. When I load it from the console, it just says "Unable to load module chan_zap.so" no matter what verbose level I am using. dmesg says: Zaptel Version: 1.4.4 Zaptel Echo Canceller: MG2 Freshmaker version: 73 Freshmaker passed register test Module 0:

Hi, I am having some issues with a new server install in Singapore. Outbound calls work fine. Inbound calls are not picked up by Asterisk. Zaptel 1.2.25 and Asterisk 1.2.28 both built from source. libpri installed wctdm and zaptel load without error Jun 6 23:34:03 fs01 kernel: [211138.372933] Zapata Telephony Interface Registered on major 196 Jun 6 23:34:03 fs01 kernel: [211138.372937]

I'm having problems with a TDM22B. The FXO modules work fine. Both FXS modules fail to initialized. The error messages I see when the module loads: Init Indirect Registers UNSUCCESSFULLY. Indirect Registers failed verification. I already RMA'ed a TDM22B because of this problem. Now that the replacement shows a similar issue, I want to see if anyone else can think of something to

Hi all, I'm trying to install a TDM400P card, and I need some help. Please, see below... after dmesg command: [root@voip root]# dmesg via82cxxx: board #1 at 0xD800, IRQ 5 Zapata Telephony Interface Registered on major 196 PCI: Found IRQ 3 for device 00:09.0 PCI: Sharing IRQ 3 with 00:10.1 Freshmaker version: 71 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1:

Hi, I'm trying to get up and running a TDM400 with a standard italian pots line but i'm having problems at getting asterisk to detect when the line get answered on outgoing calls. I'm using asterisk 1.6 beta 9 with zaptel 1.4.11. I tried with and without answeronpolarityswitch=yes but it didn't change anything at all. With callprogress=yes answer get never detected. With

Hi all, I was wondering if anyone had any pointers on how to determine whether or not a module has gone wonky on the TDM400P? I have a 2 FXO (channels 3 and 4) and 2 FXS unit (channels 1 and 2). The bad (?) module in question is the FXO module on channel 3. I can't dial in to or out of that channel; dialing in gives a busy signal, dialing out just shows * hanging around after attempting a

I apparently have a dead FXS module. Is there any kind of test I can run on it (on a live system) to determine if its good or bad? The telephone has no dialtone, gets no calls. It has been working for several months, and just quit yesterday. Thanks! Found a Wildcard TDM: Wildcard TDM400P REV I (4 modules) Freshmaker version: 73 Freshmaker passed register test Module 0: Installed -- AUTO

Hi i have buy a Digium TDM400P with 1 fxo modules TDM01B for connect my asterisk to a french analog line. In my zaptel.conf, i have: loadzone=fr defaultzone=fr fxols=3 when i load the module, i have in logs: Nov 24 06:13:40 gw kernel: Freed a Wildcard Nov 24 06:13:40 gw kernel: Zapata Telephony Interface Unloaded Nov 24 06:13:40 gw zaptel: Removing zaptel module: succeeded Nov 24

I have a TDM400. Just updated Fedora 12 to kernel 2.6.32. Rebuilt and installed dahdi-2.2.1. kernel modules loaded. lsmod | grep wctdm wctdm 37233 0 dahdi 194985 1 wctdm lsmod | grep dahdi dahdi 194985 1 wctdm crc_ccitt 1549 2 dahdi,isdnhdlc dmesg: dahdi: Telephony Interface Registered on major 196 dahdi: Version: 2.2.1

hi, i have problem with pass-through faxing with this scenario hylafax(iaxmodem) - iax - asterisk1 1.2.22 - sip - asterisk2 1.2.X(xen virtual) - linksys ATA i can fax to fax2mail on hylafax but after upgrade asterisk2 to 1.4 faxing is not working hylafax(iaxmodem) - iax - asterisk1 1.2.22 - sip - asterisk2 1.4.X(xen virtual) - linksys ATA configuration is same do you hava any idea what is

I installed the TDM400P and installed it on a system running on Fedora Core1, please refer to the steps below. I connected an analogue phone to the FXS port. When I pick up the speaker I don't hear the dialtone although when I press a number key I hear a DTMF generated. What could be the problem? I appreciate your help 1- First I installed the TDM400P in the PCI slot and connected

I'm running Asterisk on a Gentoo box with the Zaptel 1.2.1 drivers. If I boot the machine without having the wcfxs module autoload, then install the module with modprobe, asterisk works just fine. If I boot the machine and autoload the wcfxs module, the module loads fine: > Jan 11 11:06:55 asterisk Zapata Telephony Interface Registered on major 196 > Jan 11 11:06:55 asterisk ACPI: PCI

From asterisk -cvvvvv == Parsing '/etc/asterisk/chan_dahdi.conf': == Found == Parsing '/etc/asterisk/users.conf': == Found -- Automatically generated pseudo channel [Nov 11 17:43:28] WARNING[5756]: chan_dahdi.c:18155 process_dahdi: Ignoring any changes to 'userbase' (on reload) at line 23. [Nov 11 17:43:28] WARNING[5756]: chan_dahdi.c:18155 process_dahdi:

Hi, Can anyone help me with this: I have downloaded latest stable version of Asterisk using the asterisk-update.sh script. Compilation and installation passed well. When I start Asterisk I get the following error: [pbx_realtime.so]Jan 28 09:35:08 WARNING[3253]: loader.c:258 ast_load_resource: /usr/lib/asterisk/modules/pbx_realtime.so: undefined symbol: ast_load_realtime_multientry Jan 28

Hi, I have just started to setup and configure my asterisk box and am having trouble with it. I have a dlink nic in the box as well as the digium card. When the nic is in there by itself it works, but when I put the tdm400p in, there seems to be some sort of conflict with the network card. The tdm appears as another type of network card, which I don't think it should, should it? It shows