asterisk users - Jan 2006 - Zaptel modules load, but Asterisk fails at startup

I'm running Asterisk on a Gentoo box with the Zaptel 1.2.1 drivers.

If I boot the machine without having the wcfxs module autoload, then
install the module with modprobe, asterisk works just fine.

If I boot the machine and autoload the wcfxs module, the module loads fine:
> Jan 11 11:06:55 asterisk Zapata Telephony Interface Registered on major 196
> Jan 11 11:06:55 asterisk ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
> Jan 11 11:06:55 asterisk PCI: setting IRQ 10 as level-triggered
> Jan 11 11:06:55 asterisk ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link
[LNKC] -> GSI 10 (level, low) -> IRQ 10
> Jan 11 11:06:55 asterisk Freshmaker version: 73
> Jan 11 11:06:55 asterisk Freshmaker passed register test
> Jan 11 11:06:55 asterisk Module 0: Installed -- AUTO FXS/DPO
> Jan 11 11:06:55 asterisk Module 1: Not installed
> Jan 11 11:06:55 asterisk Module 2: Not installed
> Jan 11 11:06:55 asterisk Module 3: Installed -- AUTO FXO (FCC mode)
> Jan 11 11:06:55 asterisk Found a Wildcard TDM: Wildcard TDM400P REV I (2
modules)
The module is running:
> asterisk sfbosch # lsmod
> Module                  Size  Used by
> wctdm                  39936  -
> zaptel                226756  -
> asterisk sfbosch #               
But Asterisk behaves as though it were not:
>  [chan_zap.so] => (Zapata Telephony w/PRI)
>   == Parsing '/etc/asterisk/zapata.conf': Found
> Jan 11 11:32:53 WARNING[5778]: chan_zap.c:920 zt_open: Unable to specify
channel 1: No such device or address
> Jan 11 11:32:53 ERROR[5778]: chan_zap.c:6847 mkintf: Unable to open channel
1: No such device or address
> here = 0, tmp->channel = 1, channel = 1
> Jan 11 11:32:53 ERROR[5778]: chan_zap.c:10251 setup_zap: Unable to register
channel '1'
> Jan 11 11:32:53 WARNING[5778]: loader.c:414 __load_resource: chan_zap.so:
load_module failed, returning -1
> Jan 11 11:32:53 WARNING[5778]: loader.c:554 load_modules: Loading module
chan_zap.so failed!
> Warning, flexible rate not heavily tested!
> asterisk sfbosch # Ouch ... error while writing audio data: : Broken pipe
Looking at this now as I write this, it seems that some module
dependencies aren't loading, but I can't be sure. Does anybody have an
idea what's going on here?

-Stephen-

On Wed, January 11, 2006 19:35, Stephen Bosch said:
> I'm running Asterisk on a Gentoo box with the Zaptel 1.2.1 drivers.
>
> If I boot the machine without having the wcfxs module autoload, then
> install the module with modprobe, asterisk works just fine.
>
> If I boot the machine and autoload the wcfxs module, the module loads
> fine:
>
>> Jan 11 11:06:55 asterisk Zapata Telephony Interface Registered on major
>> 196
>> Jan 11 11:06:55 asterisk ACPI: PCI Interrupt Link [LNKC] enabled at IRQ
>> 10
>> Jan 11 11:06:55 asterisk PCI: setting IRQ 10 as level-triggered
>> Jan 11 11:06:55 asterisk ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link
>> [LNKC] -> GSI 10 (level, low) -> IRQ 10
>> Jan 11 11:06:55 asterisk Freshmaker version: 73
>> Jan 11 11:06:55 asterisk Freshmaker passed register test
>> Jan 11 11:06:55 asterisk Module 0: Installed -- AUTO FXS/DPO
>> Jan 11 11:06:55 asterisk Module 1: Not installed
>> Jan 11 11:06:55 asterisk Module 2: Not installed
>> Jan 11 11:06:55 asterisk Module 3: Installed -- AUTO FXO (FCC mode)
>> Jan 11 11:06:55 asterisk Found a Wildcard TDM: Wildcard TDM400P REV I
(2
>> modules)
>
> The module is running:
>
>> asterisk sfbosch # lsmod
>> Module                  Size  Used by
>> wctdm                  39936  -
>> zaptel                226756  -
>> asterisk sfbosch #
>
> But Asterisk behaves as though it were not:
>
>>  [chan_zap.so] => (Zapata Telephony w/PRI)
>>   == Parsing '/etc/asterisk/zapata.conf': Found
>> Jan 11 11:32:53 WARNING[5778]: chan_zap.c:920 zt_open: Unable to
specify
>> channel 1: No such device or address
>> Jan 11 11:32:53 ERROR[5778]: chan_zap.c:6847 mkintf: Unable to open
>> channel 1: No such device or address
>> here = 0, tmp->channel = 1, channel = 1
>> Jan 11 11:32:53 ERROR[5778]: chan_zap.c:10251 setup_zap: Unable to
>> register channel '1'
>> Jan 11 11:32:53 WARNING[5778]: loader.c:414 __load_resource:
>> chan_zap.so: load_module failed, returning -1
>> Jan 11 11:32:53 WARNING[5778]: loader.c:554 load_modules: Loading
module
>> chan_zap.so failed!
>> Warning, flexible rate not heavily tested!
>> asterisk sfbosch # Ouch ... error while writing audio data: : Broken
>> pipe
>
> Looking at this now as I write this, it seems that some module
> dependencies aren't loading, but I can't be sure. Does anybody have
an
> idea what's going on here?
>
> -Stephen-
Try running ztcfg -vvv

-- 
F Peeters
  PIII 450 - 1 GB - * 1.2 - BRIstuff 0.3.0 Pre 1 - Florz patch
  2 Sweex HFC-PCI modes=2 sync_slave=2 timer_card=0
    Cologne HFC-S pins #52, #54, #55 connected in parallel for synching.
  AMD Duron 1GHz - 1GB - * 1.2.1
  2 Sweex HFC-PCI cards