similar to: QuadBRI ,TDM400 and SuSE9.2 (Sencond try)

Hi all, We need help with our SuSe9.2 asterisk box We have one QuadBRI and one TDM40B in an ASUS pundit R-2 barebone. We have downloaded the bristuff (0.2.0-RC7j) and installed it without problems. once we downloaded and compiled asterisk, zaptel and all other stuff, the module installation succed in this order: modprobe zaptel modprobe qozap modprobe wcfsx then the ztcfg output this: Zaptel

Hi all, i'm trying to install Asterisk with Junghanns QuadBri ISDN card: I have followed all the instructions, and when I run "|ztcfg -tvv" I get | | Zaptel Configuration ======================| SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) Channel map: Channel 01: Individual Clear channel (Default) (Slaves: 01) Channel 02: Individual Clear channel (Default) (Slaves: 02)

Hi, I'm trying to connect quadbri between powered ISDN phone and ISDN line: ISDN <---1---> TE - * - NT <--2--> Phone I use quadbri, suse 9.2 and latest 0.2.0-RC7k bristuff. I've used sample settings provided with package, but do get strange error (I think that I have wrong setting for P2P or P2MP setting and cables 1 and 2). If I connect phone to ISDN with straight cable

Hi, we are trying to install Junghann's quadBRI into Dell PowerEdge 2800 system without success. I don't know if the issue can be that Junghann's card fits 32-bit slot and Dell PE 2800 has only 3 PCI-X 64-bit slots. Can this be an issue? We get "CRC errors for HDLC frame" when the card is initialized. Any idea what can be wrong? 1/ We use latest bristuff packages. 2/

Hi all, I'm trying to get a junghanns QuadBRI to coexist in the same machine as a Digium TDM400P card (so I can run the ISDN lines in and bridge with analog phones plugged into the TDM). I'm having a problem loading the modules. If I follow the BRIstuff (0.3.0-pre-1l) install method.... it's to modprobe zaptel, then insmod qozap.o I'm on Debian 2.4.31. That works. But then I

Hi List, I'm setting up a system with one TDM400P (2*FXO + 2 * FXS) and one Junghanns QuadBRI on a Fedora Core 6 (Kernel 2.6.20-1.2944.fc6). I'm using the bristuff-0.3.0-PRE-1y-e kit. It download zaptel-1.2.16, libpri-1.2.4 and asterisk-1.2.17 When it's the time for ztcfg to do its job it complains with <ZT_SPANCONFIG failed on span 2: No such device or address (6)>

- I'm not a Linux user i'm trying to get in it ... - Fedora core 1 - QuadBRI card bought from junghanns.net - We want to use the card in TE mode to connect to the TELCO - Downloaded BRISTUFF0.0.2(stable) latest from junghanss.net/asterisk - followed the instructions on voip-info.org - compiled everything still got the error when "make load" in qozap : insmod ./qozap.o

I installed the QuadBri card in my * server. I'm installing * on a RedHat 9 server I run the install.sh file. So far no problems. If I try to start /sbin/ztcfg -v -c /etc/zaptel.conf I will see the following error: Zaptel Configuration ====================== SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) SPAN 2: CCS/ AMI Build-out: 399-533 feet (DSX-1) SPAN 3: CCS/ AMI Build-out:

Hello, I cannot make any call with my new quadBRI card from Junghanns.net in my asterisk box. My asterisk box is built on Fedora Core 3 linux system. After compiling drivers from junghanns.net the card driver was loaded correctly with - modprobe zaptel - insmod qozap.ko ( as FC3 is running a 2.6 linux kernel) - ztcfg -vvv ( shows 12 channels correctly configured and the 4 leds on the card were

Hi there, I am attempting to set up a simple BRI and SIP based platform using * with the quadbri card (it's not sharing an IRQ). I enclose my zaptel and zapata.conf files. For the inital test I'm simply trying to connect to the * demo menu. The drivers compile (with a few warning that I believe aren't important - see attachments). chan_zap comiles with the warning: chan_zap.c:

Hi All ... I'm running Asterisk 1.2.13-BRIstuffed-0.3.0-PRE-1v which has a Junghanns QuadBri card in it (lspci reports Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01)) I have a regular KPN ISDN2 Line connected which works fine with the the zapata.conf below. However, I also have a new KPN ISDN Mutli (meervoudig) line (PBAX-Group), which works fine for incoming calls,

Hi, I'm trying to install a Junghanns quadbri for a few days but i stay with an asterisk error. (Everyone is busy/congested ) Asterisk is working with a Fritz PCbut from one year and now i want to add the quadbri. The quadbri card has been configured in NT mode and with no 100 ohms S/T termoination. (I'm not sure if the S/T parameter is correct) I have installed the bristuff package

Hello, I am trying to install the drivers for the Junghanns quadBRI card, but am having a problem. I have essentially followed the procedure from http://www.voip-manager.net/installation-linux-asterisk.php. At the stage to install the ISDN card I have completed the following: 1) downloaded the bristuff-0.2.0-RC8q.tar.gz to /usr/src 2) unpacked it in /usr/src - tar xvzf bristuff-0.2.0-RC8q.tar.gz

Hi everybody I hope that somebody can help me with the following .... I have 2 quadbri cards 2 - 1t0 cards 1 pabx alcatel 4200 I would like to connect my asterisk to the alcatel , I installed bristuff 0.3.0-1p , loaded the zaphfc driver in NT mode configured zaptel and zapata , it works great. then I removed the 1 t0 card, added the quadbri loaded qozap : insmod qozap.ko ports=15 ( 4 ports

Hi, I have an asterisk box with a QuadBRI. I am close to make it work like I want: Incoming calls to SIP are OK, outgoing calls are quiet working thanks to Michael Sandee advices. My real problem is that my * box is freezing very often when I probe qozap (bri-stuff 0.0.2). I have tried two distribs (Debian Kernel 2.6, Mandrake 9.1 Kernel 2.4) and it always work for a few minutes and freezes. At

I am unable to make quadbri board to work in NT mode, in TE mode it works OK. I have set 5 jumpers to NT mode. Dmesg shows everything OK: qozap: Junghanns.NET quadBRI card configured at mem 0xd084e000 IRQ 9 HZ 100 CardID 1 qozap: S/T ports: 4 [ TE TE TE NT ] qozap: 1 multiBRI card(s) in this box, 4 BRI ports total. from Asterisk side seems to be ok. pri show span 4 Primary D-channel: 12 Status:

Hello, I have an Asterisk system with kernel 2.6.18.1 and one quadbri. I have installed the latest bristuff patches (0.3.0-PRE-1s). The system works fine, but when I do a "reboot", the system hangs unloading module "qozap". Is there any known problem with latest 2.6 kernels and qozap module? Thanks. -- Paco Brufal <pbrufal@servitux.es> ServiTux Servicios

Hello everybody, I've got Asterisk 1.2.4 running with two Junghanns QuadBRI cards using the qozap driver from bristuff 0.3.0-PRE-1l. One of the cards is running in TE mode, the other one in NT mode. Whenever I call into an empty MeetMe conference room on one of the NT ports or via SIP and hang up the call during the "you are currently the only participant in this conference"

Hi, I have a Junghanns QuadBri installed and seems to be detected and working correctly using the wcb4xxp driver All ports are configured as TE The problem is when I connect an ISDN line - the LED turns green and Dahdi status shows Alarm OK But when I try to make a call I get "All circuits are busy" cause 27 I have searched and web and tried numerous configs but it doesn't want to

Hi, I'm using a revision 6822-enabled Dahdi-Tools (see https://issues.asterisk.org/view.php?id=13897) with a Junghanns QuadBRI. 1. Do I still need qozap driver ? If positive, how is it recommended to get it ? 2. Which line should be included in /etc/dahdi/modules to have the appropriate driver loaded ? 3. The process I'm planning to use is : A- Hand edit /etc/dadhi/modules,