Chris Earle (CBL)
2006-Mar-16 08:09 UTC
[Asterisk-Users] module load order for Junghanns qozap and TDM card
Hi all, I'm trying to get a junghanns QuadBRI to coexist in the same machine as a Digium TDM400P card (so I can run the ISDN lines in and bridge with analog phones plugged into the TDM). I'm having a problem loading the modules. If I follow the BRIstuff (0.3.0-pre-1l) install method.... it's to modprobe zaptel, then insmod qozap.o I'm on Debian 2.4.31. That works. But then I still need the Digium module. (modprobe wctdm) I've tried a few different orders. Sometimes I can get the digium to load, and the qozap. but then I get an error on the ztcfg about Span invalid argument (could be my zaptel.conf I realize...) *If* I try loading the wctdm after the zaptel and qozap, the server freezes! Some loop about qozap - dropped audio card.... I don't know if the quadBRI and the TDM are conflicting/sharing the zaptel module, or if I need to modprobe zaptel before each of them? and in what order? Any suggestions appreciated... I haven't even got to figuring out what I can do with chan_capi, just want to get the BRI card on and stuff. Thanks for any ideas! -- Chris Earle -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean.
Chris Earle (CBL)
2006-Mar-16 09:30 UTC
[Asterisk-Users] module load order for Junghanns qozap and TDM card
Maybe this will shed some light about what I'm trying to do: This is some output from dmesg after this load order: modprobe zaptel insmod wcfxs insmod qozap ---- Zapata Telephony Interface Registered on major 196 Freshmaker version: 73 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1: Installed -- AUTO FXS/DPO Module 2: Installed -- AUTO FXS/DPO Module 3: Installed -- AUTO FXS/DPO Found a Wildcard TDM: Wildcard TDM400P REV I (4 modules) PCI: Enabling device 02:01.0 (0000 -> 0003) qozap: Junghanns.NET quadBRI card configured at mem 0xf889b000 IRQ 17 HZ 100 CardID 0 qozap: S/T ports: 4 [ TE TE TE TE ] qozap: 1 multiBRI card(s) in this box, 4 BRI ports total. Zaptel Configuration ===================== SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) SPAN 2: CCS/ AMI Build-out: 399-533 feet (DSX-1) SPAN 3: CCS/ AMI Build-out: 399-533 feet (DSX-1) SPAN 4: CCS/ AMI Build-out: 399-533 feet (DSX-1) Channel map: Channel 01: Individual Clear channel (Default) (Slaves: 01) Channel 02: Individual Clear channel (Default) (Slaves: 02) Channel 03: D-channel (Default) (Slaves: 03) Channel 04: Individual Clear channel (Default) (Slaves: 04) Channel 05: Individual Clear channel (Default) (Slaves: 05) Channel 06: D-channel (Default) (Slaves: 06) Channel 07: Individual Clear channel (Default) (Slaves: 07) Channel 08: Individual Clear channel (Default) (Slaves: 08) Channel 09: D-channel (Default) (Slaves: 09) Channel 10: Individual Clear channel (Default) (Slaves: 10) Channel 11: Individual Clear channel (Default) (Slaves: 11) Channel 12: D-channel (Default) (Slaves: 12) Channel 13: FXO Kewlstart (Default) (Slaves: 13) Channel 14: FXO Kewlstart (Default) (Slaves: 14) Channel 15: FXO Kewlstart (Default) (Slaves: 15) Channel 16: FXO Kewlstart (Default) (Slaves: 16) 16 channels configured. ZT_SPANCONFIG failed on span 1: Invalid argument (22) any thoughts? Chris ----- Original Message ----- From: "Chris Earle (CBL)" <cearle@cbltech.ca> To: "'Asterisk Users Mailing List - Non-Commercial Discussion'" <asterisk-users@lists.digium.com> Sent: Thursday, March 16, 2006 10:09 AM Subject: [Asterisk-Users] module load order for Junghanns qozap and TDM card> Hi all, > > I'm trying to get a junghanns QuadBRI to coexist in the same machine as a > Digium TDM400P card (so I can run the ISDN lines in and bridge withanalog> phones plugged into the TDM). > > I'm having a problem loading the modules. If I follow the BRIstuff > (0.3.0-pre-1l) install method.... it's to modprobe zaptel, then insmod > qozap.o > I'm on Debian 2.4.31. > That works. > But then I still need the Digium module. (modprobe wctdm) > I've tried a few different orders. Sometimes I can get the digium toload,> and the qozap. > but then I get an error on the ztcfg about Span invalid argument (couldbe> my zaptel.conf I realize...) > > *If* I try loading the wctdm after the zaptel and qozap, the serverfreezes!> Some loop about qozap - dropped audio card.... > > I don't know if the quadBRI and the TDM are conflicting/sharing the zaptel > module, or if I need to modprobe zaptel before each of them? and in what > order? > > Any suggestions appreciated... I haven't even got to figuring out what Ican> do with chan_capi, just want to get the BRI card on and stuff. > > Thanks for any ideas! > > > -- > Chris Earle > > > -- > This message has been scanned for viruses and dangerous content by > MailScanner, and is believed to be clean. > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > Asterisk-Users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users-- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean.