similar to: Amphenol cables?

What server hardware would you recommend for an Asterisk system which are really critical? The additional hardware will probably be two digium TE110P cards, and an Adit 600 platform. If it's possible to run on -48VDC, It would be great! Are there any experiences with any HP or FujitsuSiemens systems? Or other "complete server" systems? Thanks! BR Daniel Nystr?m

I am hoping to replace my Nortel 8x24 switch with Asterisk. Right now my cabling comes from my outside phone box into my office and into a punchdown block and leaves the punchdown block as an amphenol connector which currently plugs into the Nortel swicth. A second amphenol connector them plugs into the switch and extends to another punchdown block that I believe carries the lines throughout the

I'm looking for a source for 50-pin amphenol cables, the ones used to connect Adtran's to punch down blocks. Preferably, one that's mail order and takes orders over the internet. Thanks.

Hi again folks! ;) As before, I will transform one E1 30 Channel PRI into 30 FXS channels using Adit 600. Now I'm into choosing server platform. And the two opponents are: * Dell PowerEdge 750 w/ SCSI RAID (or even SATA RAID1) * FujistuSiemens PRIMERGY RX100 S2 (SATA RAID1) As I've seen people having problem with HP server, I havn't looked at it at all. What experience do you

Got at suggestion from CarrierAccess to use the Adit 600 as an VoIP router using MGCP IP protocol, instead of controlling it through an E1. Have anyone tried this configuration? How does MGCP works? I've tried to search for it on Google, but I only find the protocol specification for it. Is Asterisk fully capable of this? I can't find any documentatin covering the use of MGCP in Asterisk.

I've finally got my Adit 600 and are configuring it right now. But I have to say, there aren't much documentation for it. I've setup MGCP and Asterisk seems to find it. But all channels (40 FXS channels) are "Down"! But the MGCP itself is "Up" according to the statistics. I can't find any documents how to set each channel to "Up" in the CLI. Any

I am getting ready to experiment with the Tellabs 2752 echo canceller. I have a 255D shelf (and power supply), but am struggling a little on connecting the echo canceller to a PRI. The shelf has 4 25-pair amphenol connectors. The two on the line side are marked "Receive In" and "Send Out". The 2 connectors on the drop side are marked "Send In" and "Receive

According to CarrierAccess, the Adit 600 uses CAS for voice signalling. What is this? This should not be a problem for Asterisk? Does the Asterisk server need to reencode CAS into aLaw when going to Euro ISDN? BR Daniel Nystr?m

Do anyone knows abount European resellers of these products: * Digium Wildcard TE410P * CarrierAccess Adit 600 Preferably in Sweden, but Europe is also better. Have anyone within EU ordered products from these companies directly from the US? In that case, how is the service and delivery? Thanks, folks!

Hi, I just got a T1 interface for a AT&T (became Lucent) System75 (uses same cards as Definity). I would take a crack at making a cable but can't determine the pinout for a cable and it is not apparent from the board. Asking you guys makes sense as one of you may have one of these systems. The cable has a amphenol male D50 connector on one end and probably a rj45 on the other. I also

Are there much performance differences when using XEON or not? In my case, I will go with muLaw both in and out of Asterisk. Are there really any processing at all if it's using same codec all the way?

Jon, I actually had some more discussions with Tim on this issue, and it seems that the channel bank would still be a good option to choose for internal purposes. I would not see any other solution than a channel bank to connect many 2wire phones into one asterisk box. I had a talk today with Carrier Access, and it seems that the adit would do us fine. The fxs cards of the adit 600 are

I know a few ppl have those CAC Adit 600's with t400 I can't seem to get my second span up on the T400 connected to the second spand on the adit (A:2) A:1 seems ok Can someone post they zaptel.conf span defintions And maybe a "print config" from the adit 600 cli I think my issue is timing srcs the coding, framing. bld out are all matched thx -------------- next part

I'm trying to use ZapRAS to enable ppp connection through my E1. After the ZapRAS command is executed, all sound is crappy on all lines! The only solution is to reboot the machine (or halt it, and then power it on since Digium's hardware doesn't like reboots). Anyone know how this can happen?! I'm using * 1.0.6 on Dell PowerEdge 1850 which are told (too late though) not to work

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi All, I'm having a tough time trying to find prices from dealers in Canada for some equipment. I am trying to implement an Asterisk box into a small business using 24 FXS ports and 8 FXO ports. I need to find the pricing for all the relevent equipment: cables, patch panels, channel bank chassis, cards etc..etc.. I think I'm going to tie

Hi, Anybody out there running Adit600s? I have in my care an Adit600 channel bank connected to an old (version 1.0.6) Asterisk instance with MGCP. When trying a more recent Asterisk (1.4.21.2~dfsg-3+lenny1, Stock current Debian) calls fail. I have attempted to add the "slowsequence = yes" line to mgcp.conf. (It seemed to be the only likely candidate in the example files I found

We have been experiencing static noise on one of our phone lines connected to our Adtran Total Access 750 which is then connected to a T100P card. I was convinced that, after rain storms, the static would get worse, it was surely a problem of Verizon's. Verizon sent a field rep out today and he told our secretary (I was busy) that there was a hard ground on the Ring portion of the line.

Thanks Harry. I will check and revert. I hope it work perfectly with asterisk. Regards On Wed, Feb 17, 2016 at 8:32 AM, Harry McGregor <hmcgregor at biggeeks.org> wrote: > Hi, > > For analog, I really like telco grade channel banks. > > I would recommend the adit 600, there is a good market on Ebay, and you > can do 48 channels per adit 600, with 2 T1 interfaces. Having

Folks, I'm experimenting with bringing multiple (8) analog lines from our local telco into a Carrier Access ADIT 600 channel bank with an FXO module, then having this talk to Asterisk via the T1 TDM controller on the ADIT and a TE405P card. I don't know if this will work well (ie: give me decent echo cancellation, call disconnect supervision, caller ID etc) but I haven't had much

After buying some additional lines from my telco, I recently had my phone vendor wire the additional lines from my phone box into an amphenol connector that's plugged into my channel bank (Adit 600). However, although I make the following changes in my zaptel.conf and my zapata.conf files respectively and then reboot, the new channels, when selected for an outbound call, resume a dialtone