similar to: Polycom IP600 stuck at "Running App = sip.ld"(was: Re: Polycom 1.4.1 firmware for IP500/IP600)

I have these phones working well with Asterisk, thanks to http://www.freedomphones.net/polycom/files The code there is not the most current (and my Polycom Extranet login hasn't gotten updated yet to allow downloads). Been waiting a while for their support folks to update the access. If you know where I can get the 2.5.0 BootROM and 1.3.1 SIP code? Thanks, L.

Hello, Does anybody have the latest Boot ROMs for the IP500 and IP 600 Polycom phones. I have one of each and can't find the Boot ROM v 3 anywhere to download. I would also love a good sample phone.cfg and sip.cfg files from an Aussie asterisk user to look at. Also the ip500 is having problems trying to load the bootrom 2.6.2 ? Any ideas? Kind regards Michael Felder IT Medic

Hi, I want to reset IP600 to the factory settings but when I press 468* and hold it asks for password? Is there another way? Robert

Hello, I have configured my polycom ip600 and ip500. The phone works well. But the clock is wrong and flashes the whole time. Drives me nuts! I have set the time offset on the DHCP / boot server. 36000 (I'm in Australia!) It doesn't seem to help... Mike

Hello, I am looking at the Polycom phones. The ip600 has a very nice screen, is that the only real advantage over the ip500 and ip300.. Is it worth the extra dollars? Kind regards Michael Felder IT Medic Australia Pty. Ltd. P: 03 9557 2213 F: 03 9557 2214 M: 0419 568 217 E: Michael@ITMedic.com.au <blocked::mailto:Michael@ITMedic.com.au> http://www.ITMedic.com.au

I'm having trouble with both my Polycom IP600 and IP500 disconnecting calls to the PSTN after about 1 hour. The below log is of a phone call that lasted 1hr 39mins which is my record so far. I cannot figure out what is causing the call to terminate and I am hoping somone on this list can help me. In this example both the phone and the asterisk server have public IP addresses so NAT shoul not

Have a strange problem... When a C7960 calls the Polycom ip600, the ip600's first line button blinks, the ip600 display shows the proper callerid, but the phone does not ring at all. If I call the same ip600 from a bt102, the ip600 rings properly. If I call the same ip600 from another C7960, the ip600 rings properly. All phones and asterisk are on the same lan within a few feet. The

FYI for anyone using the dual ethernet ports on a Polycom IP600. I'm using a Polycom IP600 connected to an HP2524 10/100 switch, which has an asterisk box connected directly to it. No VLANs defined or in use. Measured bandwidth: PC -> HP Switch -> Asterisk : actual throughput measured at 94.1 mbps. PC -> IP600 -> HP Switch -> Asterisk : actual measured at 91.9 mbps. The

Hi list! Does anyone have experiences with the updated model of the Kirk IP600? The V3 model is supposed to support SIP instead of only SCCP or H323 which would make the use with Asterisk a lot easier. I have only tested the Kirk IP600 V2 with SCCP / Skinny protocol which is still giving me severe headaches : - the standard Skinny driver in * doesn't work, only the version of Sergio

I'm going to try, Thanks very much Giordano -----Messaggio originale----- Da: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] Per conto di Remco Barende Inviato: luned? 30 gennaio 2006 20.04 A: Asterisk Users Mailing List - Non-Commercial Discussion Oggetto: Re: [Asterisk-Users] Kirk IP600 Hi! Yes, it works (sort of) but I still have some issues.

Hi list! Is anyone using the Kirk IP600/3 with SIP firmware connected to Asterisk? Any experiences / caveats? If anyone would be willing to share the dump of their IP600 config file, i would really appreciate it. Is there anything special i should put in my asterisk config? Thanks !!! Remco

The piece of plastic is built in to the IP600. Use a screwdriver or something similar and push the little piece of plastic out from the top inside the cradle. It will pop out, and you can turn it over and reinsert it upside down to hold the receiver in place. ________________________________ From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On

Passing this along. I got it tonight from a friend: Basis Technology has uncovered a potentially serious issue with the Polycom SoundPoint IP600 SIP phones, which causes them to spontaneously reboot at unpredictable times. It appears that if the amount of current being delivered to the phone falls below a certain threshold, the phone will reboot. Here are the specific circumstances which will

Hi, I'm testing a Polycom IP600. With firmware version 1.1 the phone reboots at any time. With firmware version 1.2, the first reboot was an endless reboot. Then I moved the phone to another lan port, then it worked fine. Then I installed again in the initial lan port and the phone works well. However after some time of inactivity (1 hour?), the IP600 stops to send and receive calls.

Hi, I am mostly happy with my Polycom IP600 but it apparently needs to check the FTP server every minute. I couldn't find any obvious setting related to that behavior in the configuration files. Any idea how to curb the IP600's spurious network activity? Thanks, -- Lord, protect me from your followers.

Hi all, has anyone tryied to configure asterisk with Kirk IP600 Dect-IP gateway? Could it works using the skinny channel ? Thanks Giordano -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060130/07ec3c90/attachment.htm

Hi all, I dont know why, but if I plug my PC inside the 'PC' slot on my polycom, this is not working. (Polycom IP600 is online on the net.) I'm using normal network cables. (I see jumpers behind the phone... do I need to play arround with that?) Any help would be appreciated. -- Alexandre Leclerc

I have been testing with Polycom IP600 phones for a month or so. I found out that there are frequent problems with the handset. The problem is I can hear the other end but the other end cannot hear me. I have already downloaded the latest bootROM 3.1.3 and sip 2.1.2 However, there are no problems with the headset or speaker phone. Has anyone encountered such problems before? Thanks.

Hi All, Can someone please advise me about configuring my Polycom IP600? I have an account with a SIP based IP Centrex provider. The basic SIP info and line 1 config points to them. That's working fine. I'd like to register line 2 with my own asterisk server. I've tried putting the basic registration info in the line 2 configs...but the phone never registers. Not certain how to

Hello, I have a polycom ip600 and eyebeam. When I call from polycom to eyeBeam, everything, including audio works. When I call the other side (from eyeBeam to polycom), I get no audio. In both cases, eyeBeam shows the same codec: g711u. Also sip show channels shows ulaw codec for both sides and correct addresses. I have canreinvite=no. I don't know if it's important, but asterisk