similar to: TDM400 success?

I recently swapped 2 FXO modules on to what had previously been a 4 FXS version of the TDM400 board. The FXS ports are recognized - the FXO ports don't appear to be recognized (ie modprobe wcfxo and ztcfg both say channel 1 isn't there). Has anyone experienced this problem? All software is current as of this AM. If the old FXS modules are re-installed all works just dandy (other than

Anyone know of any equipment that I can use to connect a laptop running asterisk to a POTS line (RJ11) ? Regards, Dovid __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com

Hey gang, I'm looking at escaping from a Nortel Meridian CISC system to Asterisk/Digium/SIP phones. I'm currently in the testing and proof of concept phase. I'm going to need a SIP phone and don't want to re-purchase and have "orphans" around. We currently run Nortel 7310 phones and they work great. I'm sort of overwhelmed by all of the different IP phones. I

I have had a TDM400 with 2 FXO and 2 FXS working for ages (>12 months). It has stopped working. All four green lights are still lit. I have rebuilt zaptel and asterisk and restarted but the problem persists. /sbin/ztcfg -vvvv Zaptel Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Slaves: 01) Channel 02: FXO Kewlstart (Default) (Slaves: 02) Channel 03:

Hi, Some weird problem (or I'm too sleepy) happens with a tdm04B revision G (4fxo) Steps: modprobe zaptel modprobe wctdm ztcfg -vv /etc/zaptel.conf fxsls=1-4 # TDM04B defaultzone=us loadzone=us /etc/asterisk/zapata.conf signalling=fxs_ls group=1 context=incoming channel => 1-4 modprobe zaptel and wctdm load fine, however ztcfg -vv shows: 0 channels configured Im using centos 4.4 with

I have fixed this before, but I cannot for the life of me remember how I did it. I have a TDM400P with one fxo module and one fxs module. I setup Asterisk @Home and everything works fine, except when I try and call out. If I call out with a SIP phone it calls the zap extension and not the pstn line? If I take the zap extension offhook and call with the SIP phone it dials out the pstn line

I have a TDM400. Just updated Fedora 12 to kernel 2.6.32. Rebuilt and installed dahdi-2.2.1. kernel modules loaded. lsmod | grep wctdm wctdm 37233 0 dahdi 194985 1 wctdm lsmod | grep dahdi dahdi 194985 1 wctdm crc_ccitt 1549 2 dahdi,isdnhdlc dmesg: dahdi: Telephony Interface Registered on major 196 dahdi: Version: 2.2.1

Folks, I have a Xen Asterisk VM with a TDM400 card. When I try to run dahdi_cfg, I get: tempest:~# dahdi_cfg -vvv DAHDI Tools Version - 2.2.0 DAHDI Version: 2.2.0 Echo Canceller(s): Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Echo Canceler: none) (Slaves: 01) Channel 03: FXS Kewlstart (Default) (Echo Canceler: none) (Slaves: 03) Channel 04: FXS

Hi My card is working, but when I reboot the machine, most of the times it is not working, I get "ztcfg: ZT_CHANCONFIG failed on channel 1: No such device or address (6)" To make it work again I have to shut down, remove the card, reboot so kudzu will remove the config. shut down again, put the card back in, reboot, now kudzu see it, I choose "Ignore" and then it's

I had a working Asterisk 1.4.24.1 installation on SUSE 9 Linux but SIP only. I then downloaded and installed latest Zaptel and could not get Zaptel working. So I downloaded Asterisk again and re-installed. But still problems: Here is my ztcfg output: asterisk:/etc/asterisk # ztcfg -vvvvv Notice: Configuration file is /etc/zaptel.conf line 4: Unable to read Zaptel version information. Zaptel

I just installed a new TDM400P with one FXO interface in slot 4 (how it came from Digium). This box is running Debian with a 2.6.10-rc2-mm3 kernel. After the make linux26 and make install in /usr/local/src/zaptel, I can see contents in /dev/zap but any attemp to touch for example /dev/zap/ctl gets a no such device or address ... Any suggestions?

Hi I looking a good IAX service for a *emerging * voip provider. Better with a test account to try. Thanks in advance. roberto -- Ing. Roberto Pereyra ContenidosOnline Servidores BSD, Solaris y Linux Soporte t?cnico ISPs Jabber ID: rpereyra@lugmen.org.ar For reliable and professional DNS, use DNS Made Easy! http://www.dnsmadeeasy.com/u/14989 -------------- next part

Ouch, part reset, quickly restoring reality (0) Power alarm on module 1, resetting! I have looked though a lot of email on this issue, and no one seems to have the answer. How many people are seeing this on a TDM400 card? Does anyone have a "REAL" answer to it. Yes, I do have the power connected to it! Regards Garry Taylor

Hello I setup Asterisk@Home with purely VoIP and it worked fine. I then added an X100P card so I could call out / take inbound calls via PSTN and that went fine. But I have just added a TDM400P card (specifically a TDM30B) and now problems. Here is some of the output. Any ideas on what I should be looking at next? When I run genzaptelconf -s -d I get lots of erors on screen - bit I can

Hi All - I pulled from a working system a TDM400 with one s110 fxs and three x100 fxos. I put it into a new box and the fxs no longer works. The fxos work just fine. I thought it was odd, but I chalked it up to a random chance failure and ordered another s110. The replacement doesn't work either, and now I'm confused. dahdi_scan recognizes the s110, but it says it fails. Output

Hello all. I have here a TE110P (configured as E1) and a TDM400P (with four X100P - FXS). Both boards are recognized by the operating system as showed above: 0000:08:00.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device b1d9:0003 Flags: bus master, medium devsel, latency 64, IRQ 169 I/O ports at e800 [size=256]

I have a small system based on one TDM400 card with - 2 FXO modules for incoming lines - 1 FXS module for one phone The system was working fine in the past. The motherboard was exchanged and during the switch, the phones line was rewired with a mistake and a incoming phone line was connected to the FXS module, and there was ringing voltage on the module. Now, the system kinda works but the FXS

I am getting quite frustrated today, so please bear with me. I just installed Fedora Core 4 (was running RedHat 9 with a working Asterisk) now my Fedora does not appear to be recognizing my X100P (clone) at all. Hardware browser just shows them as unknown device. driver: hisax So, of course, my zaptel drivers do not work and therefore my asterisk does not work. any help would be greatly

Looking for someone with a successful experience similar to this; I have a need to cross connect a 3COM NBX PBX PRI interface to asterisk, but over a long distance. We do not need any IP connectivity and the solution requires G.711u audio so there is no benefit to using IP. Has anyone here successfully cross connected any PBX PRI interface expecting NI2 PRI signaling B8ZS/ESF with an

Hi all, I have hit a wall configuring a TDM400, I have set these up before without issue but today I just can't seem to figure out what I am doing wrong. On an incoming call the following is produced in the Asterisk console with verbose 4 -- Starting simple switch on 'Zap/2-1' Mar 22 16:12:34 NOTICE[2051]: chan_zap.c:6063 ss_thread: Got event 18 (Ring Begin)... Mar 22