similar to: problems with X100P - Nochanneltyperegisteredfor 'Zap'

You should see something like this.... (I have 8 channels) tuxpbx*CLI> zap show channels Chan Extension Context Language MusicOnHold pseudo incoming en 1 incoming en 2 incoming en 3 incoming en 4 incoming en 5 incoming en 6

For reference... http://www.voip-info.org/wiki-Asterisk+zap+channels Not sure it is relevant but go ahead and remove the spacing on the channel line so it will read.... channel=>1 Here is the original incoming context you showed. [incoming] exten => s,1,Answer ; Answer the line exten => s,2,Playback,demo-thanks ;for playing a file The Playback looks malformed based upon the wiki

Just to make sure this isn't a typo in your original email... Is this example from your zapata.conf? Also, the extension you have shown are in extensions.conf not zapata.conf correct? Here is an example of a good zapata.conf.... [channels] language=en busydetect=yes faxdetect=both busycount=7 relaxdtmf=yes callwaiting=yes callwaitingcallerid=yes useincomingcalleridonzaptransfer=yes

Hi, I have already installed the X100P drivers but when I make to make call call, I always get No channel type registered for 'Zap'. Any idea how to solve this problem? It seems that the Zap module is not loaded but I have already load the driver by modprobe zaptel > modprobe wcfxo > ztcfg -vv thanks -------------- next part -------------- An HTML

Hi, Is there any command for checking the audio codec used or audio transcoding in the connected calls. thanks __________________________________________________ Do You Yahoo!? Download the latest ringtones, games, and more! http://sg.mobile.yahoo.com

PROBLEM: My x100p only does bad things. When I plug the line from the wall into the card, other phones in my house go nuts, no dialtone, crazy clicking, random tones, etc. Following the steps below, the line is screwed up any time I test after step 2. Just plugging the line from the wall into the x100p takes my other phones off line. External calls to my line hear busy. Obviously, can't

Hi, I would like to change the sequence of messages that was playbacked when I call to the voicemail extension, VoicemailMain. Where can I changed it, can't find the definition for VoicemailMain in extension.conf and voicemail.conf __________________________________________________ Do You Yahoo!? Download the latest ringtones, games, and more! http://sg.mobile.yahoo.com

Hello List, Im just dipping my feet into the asterisk world, and im having major fxo problems Im running Asterisk (from svn) + libpri (from svn) + asterisk-addons (from svn) + asterisk gui (svn 1.4 branch) + zaptel (svn 1.4) on a Debian Etch box, with 1gb ram, running all of the services for my home server (web / db / music server etc), and i would like to run my PSTN line from Kingston Comms,

I am running * in a development environment, adding functionality as I go. The * box has a X100P card in it which ztcfg enabled as channel 1 with fxsks signalling (fxsks=1). Everything worked fine and I was able to make inbound and outbound calls to/from the PSTN, the only issue being that some exchanges wouldn't handle the dtmf signalling, but I put that down to a peculiarity with some AU

I am just wondering if this is normal. I have my * running for a week now and I'm still testing its interoperability with other voip provider (in sip using codecs other than g711). yesterday, i changed my linux's (RH9). and since the new ip i assigned is located on a different site, i have to shut it down and move it physically. after that, i cannot run my * anymore. i am getting this

Greetings all, I've just put two X100P cards to my box and despite trying everything I can find on the web, I can't get the second one to work. I've edited /etc/modules.conf so that ztcfg doesn't run automatically. To start, I run: /sbin/modprobe zaptel /sbin/modprobe wcfxo /sbin/ztcfg /sbin/modprobe ixj and ztcfg says: ZT_CHANCONFIG failed on channel 2: No such device or

I have just purchased a 2nd hand X100P, if I do a ztcfg -vv I get: "Zaptel Version: 1.4.0 Echo Canceller: MG2 Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured." My understanding of the above is that the zaptel driver has detected the card. What do I now need to do, in order to get an incoming call to work with

Hmm, I don't have /etc/modprobe.conf, and wctdm is giving me problems. Which device is it talking about? [root@asterix /]# modprobe wctdm /lib/modules/2.4.20-8/misc/wctdm.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg

All, I'm having trouble getting the X100P working. Lsmod shows : zaptel 179808 0 I did a . # modprobe zaptel and here is my zaptel.conf (comments omitted) __SNIP__ fxsks=1 loadzone = us defaultzone=us __SNIP__ Here is zapata.conf __SNIP__ [trunkgroups] [channels] context=default switchtype=national signalling=fxo_ls rxwink=300 usecallerid=yes hidecallerid=no

Hi, I have got one X100P telephone card in my Asterisk server and it's working well. I have two phones lines and would like to install a second card so I can use both lines. I have installed the card and tried to set it up, but all to no avail ! Could someone outline the changes that I need to make (and in which .conf files) in order to get the second card going ? Thanks in advance,

hello, I just installed 2 brand new x100p cards into my linux system. Everything compliled and worked fine from the first try. Hoewver the phone lines I will use with this system have groundstart signaling. I have tried to change the zaptel.conf and zapata.conf to use this type of signaling but ztcfg gives me an error every time with the new configuration. Bellow are the config files and the

I have just got my X100p card and am trying to install it. I have built and installed the zaptel drivers without any apparent errors and I am now trying to get them working. I have the following in config files In /etc/zaptel.conf fxsks=1 In /etc/asterisk/zapata.conf signalling=fxs_ks context=default channel => 1 Now when I try ti modprobe the drivers this is what happens: Command:

I can either get the TE100P working or the 3 X100P clones working, but never both. I have the TE100P connected to a channel bank, and X100P clones to lines from the phone company. This is my zaptel.conf span=1,1,0,d4,ami fxsks=1-24 loadzone=us fxols=25-27 loadzone=us I then do [root@asterix root]# modprobe zaptel [root@asterix root]# modprobe wcte11xp ZT_CHANCONFIG failed on channel

Sorry about last posting, typo... I just added 2 Digium X100P cards. When my * box boots, it found them and configured them. When I enter genzaptelconf, it comes back with the following error: line 13: Unable to open master device '/dev/zap/ctl' Unloading zaptel hardware drivers: Removing zaptel module: rmmod: module zaptel is not loaded

I've just installed a Digitnetworks X100P clone in my * server and run the install script for the voicepet-single-x100p tarball. The install appeared to run OK with modprobe wcfxo successful and the ztcfg reporting "Channel 01: FXS Kewlstart (Default) (Slaves: 01)". When I try to start * though I get a segmentation fault after loading res_features.so. I discovered that the