Wiley E. Siler
2004-Oct-05 00:48 UTC
[Asterisk-Users] problems with X100P - No channeltyperegisteredfor 'Zap'
Just to make sure this isn't a typo in your original email... Is this example from your zapata.conf? Also, the extension you have shown are in extensions.conf not zapata.conf correct? Here is an example of a good zapata.conf.... [channels] language=en busydetect=yes faxdetect=both busycount=7 relaxdtmf=yes callwaiting=yes callwaitingcallerid=yes useincomingcalleridonzaptransfer=yes threewaycalling=yes transfer=yes cancallforward=yes usecallerid=yes echocancel=yes echocancelwhenbridged=yes echotraining=yes rxgain=1.5 txgain=1.5 group=1 signalling=fxs_ks callerid=asreceived context=incoming channel=>1-8 These ones above are the only values I need in mine. The context and channels are the last entries. Next.... Zaptel.conf located in /etc/ has these entries only... fxsks=1-8 loadzone=us This sets my 1-8 channels to the correct type of channel. Fxs kewlstart, note that zapata has a line called signalling that matches. Now finally extensions.conf [incoming] include => mainmenu include => sip Sip is my context with my internal phones Mainmenu is my context with my autoattendant settings Check the wiki on extensions.conf, zapata.conf, and zaptel.conf Regards, Wiley -----Original Message----- From: khoonking [mailto:khoonkingsg@yahoo.com.sg] Sent: Tuesday, October 05, 2004 12:15 AM To: 'Asterisk Users Mailing List - Non-Commercial Discussion' Subject: RE: [Asterisk-Users] problems with X100P - No channeltyperegisteredfor 'Zap' Hi, I have confirmed that there is no space between "=>" but still the same problem.> zapatel.conf > =======================> [channels] > signalling=fxs_ks > context=incomingchannel => 1 ;X100P>[incoming] >;exten => s,1,Echo ;for testing the connection >exten => s,1,Answer ; Answer the line >exten => s,2,Playback,demo-thanks ;for playing a file> [default] > exten => 6200,1,Dial(SIP/6200,20) > exten => 6203,1,Dial(SIP/6203,20) > exten => _X.,1,Dial,Zap/1/${EXTEN}When I call from an analog phone to the X100P ext, Asterisk CLI screen does not print anything. Based on my configuration, it should answer the call automatically and playback demo-thanks. When I tried to dial out using the SIP IP-Phones, I am getting Executing Dial("SIP/6201-f848", "Zap/1") in new stack Oct 5 15:01:41 WARNING[15375]: channel.c:1901 ast_request: No channel type registered for 'Zap' Oct 5 15:01:41 NOTICE[15375]: app_dial.c:742 dial_exec: Unable to create channel of type 'Zap' == Everyone is busy/congested at this time Anyway way of ckecking that my Zap channel is working? Meng Kim -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Steven Critchfield Sent: Tuesday, October 05, 2004 2:30 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: RE: [Asterisk-Users] problems with X100P - No channeltyperegistered for 'Zap' Don't group reply. I get mail just fine from the mailing list like everyone else. The mailing list is properly set up to promote community by helping keep discussions on the list for all to see and benefit. On Tue, 2004-10-05 at 14:23 +0800, khoonking wrote:> Hi, > > This is what I have configured. I have connected 2 sip IP-Phones to > the asterisk. SIP IP-Phone 1 can call SIP IP-Phone 2. The X100P is > connectedto> my PBX ext 100. > I would like my SIP IP-Phones to be able to call to my office colleageext,> e.g. 101 > And my IP-Phones to receive incoming call from PBX. > > > Zaptel.conf > ==================== > fxsks=1 #X100P > loadzone = us > defaultzone=us > > > zapatel.conf > =======================> [channels] > signalling=fxs_ks > context=incoming > channel = >1 ;X100PVerify there isn't a space in between the equals sign and the greater than sign. I am betting you are getting a parse error there and it is causing you the grief. Also add a group there so your system is prepared for growth. It is good form too.> extension.conf > > [default] > exten => 6200,1,Dial(SIP/6200,20) > exten => 6203,1,Dial(SIP/6203,20) > exten => _X.,1,Dial,Zap/1/${EXTEN}once you have a group defined above, this changes to g1 or whatever group number you define. Again good form in case you add a second line, you only have to configure the line into the group and your extensions file is good to go. -- Steven Critchfield <critch@basesys.com> _______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users The information transmitted is intended only for the person or entity to which it is addressed and may contain confidential and/or privileged material. Any review, retransmission, dissemination or other use of, or taking of any action in reliance upon, this information by persons or entities other than the intended recipient is prohibited. If you received this in error, please contact the sender and delete the material from any computer
khoonking
2004-Oct-05 02:03 UTC
[Asterisk-Users] problems with X100P - Nochanneltyperegisteredfor 'Zap'
Must I build the source code for Zapata since I am using the Zapata.conf? -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Wiley E. Siler Sent: Tuesday, October 05, 2004 3:48 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: RE: [Asterisk-Users] problems with X100P - Nochanneltyperegisteredfor 'Zap' Just to make sure this isn't a typo in your original email... Is this example from your zapata.conf? Also, the extension you have shown are in extensions.conf not zapata.conf correct? Here is an example of a good zapata.conf.... [channels] language=en busydetect=yes faxdetect=both busycount=7 relaxdtmf=yes callwaiting=yes callwaitingcallerid=yes useincomingcalleridonzaptransfer=yes threewaycalling=yes transfer=yes cancallforward=yes usecallerid=yes echocancel=yes echocancelwhenbridged=yes echotraining=yes rxgain=1.5 txgain=1.5 group=1 signalling=fxs_ks callerid=asreceived context=incoming channel=>1-8 These ones above are the only values I need in mine. The context and channels are the last entries. Next.... Zaptel.conf located in /etc/ has these entries only... fxsks=1-8 loadzone=us This sets my 1-8 channels to the correct type of channel. Fxs kewlstart, note that zapata has a line called signalling that matches. Now finally extensions.conf [incoming] include => mainmenu include => sip Sip is my context with my internal phones Mainmenu is my context with my autoattendant settings Check the wiki on extensions.conf, zapata.conf, and zaptel.conf Regards, Wiley -----Original Message----- From: khoonking [mailto:khoonkingsg@yahoo.com.sg] Sent: Tuesday, October 05, 2004 12:15 AM To: 'Asterisk Users Mailing List - Non-Commercial Discussion' Subject: RE: [Asterisk-Users] problems with X100P - No channeltyperegisteredfor 'Zap' Hi, I have confirmed that there is no space between "=>" but still the same problem.> zapatel.conf > =======================> [channels] > signalling=fxs_ks > context=incomingchannel => 1 ;X100P>[incoming] >;exten => s,1,Echo ;for testing the connection >exten => s,1,Answer ; Answer the line >exten => s,2,Playback,demo-thanks ;for playing a file> [default] > exten => 6200,1,Dial(SIP/6200,20) > exten => 6203,1,Dial(SIP/6203,20) > exten => _X.,1,Dial,Zap/1/${EXTEN}When I call from an analog phone to the X100P ext, Asterisk CLI screen does not print anything. Based on my configuration, it should answer the call automatically and playback demo-thanks. When I tried to dial out using the SIP IP-Phones, I am getting Executing Dial("SIP/6201-f848", "Zap/1") in new stack Oct 5 15:01:41 WARNING[15375]: channel.c:1901 ast_request: No channel type registered for 'Zap' Oct 5 15:01:41 NOTICE[15375]: app_dial.c:742 dial_exec: Unable to create channel of type 'Zap' == Everyone is busy/congested at this time Anyway way of ckecking that my Zap channel is working? Meng Kim -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Steven Critchfield Sent: Tuesday, October 05, 2004 2:30 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: RE: [Asterisk-Users] problems with X100P - No channeltyperegistered for 'Zap' Don't group reply. I get mail just fine from the mailing list like everyone else. The mailing list is properly set up to promote community by helping keep discussions on the list for all to see and benefit. On Tue, 2004-10-05 at 14:23 +0800, khoonking wrote:> Hi, > > This is what I have configured. I have connected 2 sip IP-Phones to > the asterisk. SIP IP-Phone 1 can call SIP IP-Phone 2. The X100P is > connectedto> my PBX ext 100. > I would like my SIP IP-Phones to be able to call to my office colleageext,> e.g. 101 > And my IP-Phones to receive incoming call from PBX. > > > Zaptel.conf > ==================== > fxsks=1 #X100P > loadzone = us > defaultzone=us > > > zapatel.conf > =======================> [channels] > signalling=fxs_ks > context=incoming > channel = >1 ;X100PVerify there isn't a space in between the equals sign and the greater than sign. I am betting you are getting a parse error there and it is causing you the grief. Also add a group there so your system is prepared for growth. It is good form too.> extension.conf > > [default] > exten => 6200,1,Dial(SIP/6200,20) > exten => 6203,1,Dial(SIP/6203,20) > exten => _X.,1,Dial,Zap/1/${EXTEN}once you have a group defined above, this changes to g1 or whatever group number you define. Again good form in case you add a second line, you only have to configure the line into the group and your extensions file is good to go. -- Steven Critchfield <critch@basesys.com> _______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users The information transmitted is intended only for the person or entity to which it is addressed and may contain confidential and/or privileged material. Any review, retransmission, dissemination or other use of, or taking of any action in reliance upon, this information by persons or entities other than the intended recipient is prohibited. If you received this in error, please contact the sender and delete the material from any computer _______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users