similar to: T100P lost D channel

Hello, I'm trying to get a Wildcard T100P working with Asterisk and so far I haven't had any luck. No problems with the card itself from what I can see and the telco says that the problem is on our end (don't they always?). A small sample of what asterisk spews out on the console: Jan 13 15:45:32 WARNING[180236]: chan_zap.c:5834 zt_pri_error: PRI: Read on 43 failed: Unknown

Hi Last week I installed Asterisk (release1) with digium t100p single span T1 (wct1xxp) board on Dell GX270 pc configured for PRI. Asterisk/t100p is currently the only user of the t1 line. All worked well for about a half a day, PSTN to SIP phones to non-SIP IP phones etc. Alas, since then I consistently get multitudes of blue alarms on all b-channels followed by a loss of d-channel: Aug 31

(to mods: sorry for any extra work I've put you through. Posting from my work account, as proper) Hello all, I'm back. I've got that lucky feeling that this will all work out very soon, and I hope that that is true. The issue: In my * server I have a t100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm

Hello! I am trying to configure my PPP setup such that it only uses the first 4 channels on each T1. I see no obvious errors in /var/log/messages or when running the ztcfg, but I am able to still pass a full T1's worth of data over the PPP links. I would expect to only be able to send about 300kbps in this configuration. I am running the PPP link back-to-back on the same machine, by the

I am having some difficulty getting a T100P card to work with my PRI. When I attempt to make an outbound call via: exten => 1004,1,Dial(Zap/g1/NPANXXXXXX) I see the following on the asterisk console: -- Executing Dial("SIP/sbruton-b8ce", "Zap/g1/NPANXXXXXX") in new stack Apr 21 08:18:48 NOTICE[16401]: app_dial.c:554 dial_exec: Unable to create channel of type

Hi, I have two t100p cards installed. One card connected to the PSTN, the other card is hooked to the Definity PBX with a T1 cross over cable. The card connected to the PSTN works fine. The problem is with the card hooked up to the PBX. The light behind the card is green, but when I dial from this card I get an error. Its says it could start the D-Channel. Could someone help me out with this

My PRI is being reset at least once a day with the following errors in the logs. zaptel, zapata, libpri, and asterisk are from CVS this morning.. This has been happening for weeks on all versions (including -stable). the T100P card appears to NOT be sharing an IRQ. xenon# cat /proc/interupts CPU0 0: 1203977 XT-PIC timer 1: 3 XT-PIC keyboard 2:

I am having trouble getting my T100P and ADIT 600 talking. I have 2 FXO 8 port cards in the ADIT and a T1 controller card. I have a T1 x-over cable connecting two together. Here are copies of the relevant bits of my zaptel.conf and Zapata.conf Zaptel.conf span=1,0,0,esf,b8zs loadzone=us defaultzone=us Zapata.cfg context=default signalling=fxs_ks group=1 channel => 1-24 My

Hi all: I have problems to setup my zaptel E100P hardware. When I start * after receive the "Asterisk Ready" I see this: *CLI> Jun 22 20:37:55 NOTICE[1133718080]: chan_zap.c:4881 handle_init_event: Alarm cleared on channel 1 Jun 22 20:37:55 NOTICE[1133718080]: chan_zap.c:4881 handle_init_event: Alarm cleared on channel 2 Up to channel 31. anfter this: Jun 22 20:37:55

Don & others, Thank you for your answer. The fog maybe lifting ;). The zaptel.conf file has the following in its comments: # # The timing parameter determines the selection of primary, secondary, and # so on sync sources. If this span should be considered a primary sync # source, then give it a value of "1". For a secondary, use "2", and so on. # To not use this as a

Hi ! I am connecting to Adit 600 thru a T100P card I have configured 1-16 FXS channels and 17-24 FXO. Everything looks fine on Asterisk side I get a tone on all FXS channels, but when I try to dialout thru one of the FXO channels 17-24 it doesn't connect to the POTS line and echoes back my voice. I use fxsls and fxols for the T1 channels and ls on Adit side. Whats wrong here ? here is my Adit

Hello, I have just received Adtran TSU 600 with 24 FXS ports. I have installed sucessfuly T100P card. Adtran is connected to t100p with crossover T1 cable. On T100P card I have a green light and on Adtran I do not get any errors or alarms. But I do not get dialtone on FXS ports. Adtran is configured: For Network Timing, fxs ports ore fxs_ls on Adtran. In zaptel.conf: span=1,1,0,esf,b8zs

Hello all, I've got a T100P connected to an Adtran TA750 with a T1 crossover... This connects to a patch panel with phone ports. The Adtran is fully populated with FXS cards. All I get on any phone port is a fast clicking noise... No dialtone. Asterisk 'sees' the card, (the channels show up in /proc/zaptel). Incoming calls are routed to the zap/x channel, but no ring. I'm

I've been having some problems getting a channelized T1 working with a T100P card. Perhaps someone can help: I have an Eschelon T1 coming into a Vina Integrator box. This box splits out the T1 into an ethernet plug for bandwidth and a secondary T1 which I plug into the T100P card. I've connected the two with a T1 crossover cable. I get a green light on the t100p card and can make

Hi there, I have a new box setup using the latest version of FreePBX and the latest SVN of Asterisk 1.2 as of yesterday. Incoming calls from our PRI work fine. However, outgoing calls gives me the operator saying "The call cannot be completed as dialed" after two rings. Here's an outgoing call from extension 271: -- Executing Set("SIP/271-09f61dc0",

Hi List, a number of our customers are reporting dropped calls. here is the config. 1 T100P T1 Card 1 Asterisk (Mid Nov build) T1 is signalled as a PRI(National) The card will only sync up if we clock, if we line side clock the card goes into yellow alarm and won't sync up. the only errors we see are framing slips. Around 2500 slips over a 18 hour period. (this was reported from

I've put a t100p in our * server and I'm having trouble configuring it. It is directly connected to an Adtran TA 750 channel bank with two FXO cards (8 analog incoming lines total). I'm able to insmod and modprobe both zaptel and wct1xxp with no trouble, but when I start * with /usb/sbin/asterisk -c I get the following output: [root@rosella root]# /usr/sbin/asterisk -c Asterisk

I need to know how to setup the data side of the T1 on my Linux Box. I have found information about configuring a PRI and HDLC but nothing about the Frame-Relay type setup for data. The following is information from our T1 provider. Network T1: Framing = ESF Line code = B8ZS Build out = 0-133ft(DSX)/0dB(CSU) Clock = network Pulse-density-enforce = off alarm-option = on alarm-delay = 15

In the next week or so, we'll be turning up a new T1 Pri from Cox Cable in Omaha using a T100P (installed but not yet configured). While discussing the interface parameters with a very knowledgable Cox engineer, we decided on some of the basics including b8zs, esf, dchan=24, callerid, 5 digits of called number forwarded to *, and switchtype=national (NI2). They indicated their CO switch is a

Hello all, I got a problem at an asterisk server, with dropping calls, losing all channels and reaktivating all channels and beeing back up. This problem seems to occure randomly over the whole day, when it gots traffic on the card. After looking @ google I found several hints but none did work fine. To avoid problems with the phone line (german E1) I called the provider, he did a 45 min. route