similar to: Polycom SoundPoint IP 500/600 XML minibrowser

I'm trying to develop a company phone list accessible via the minibrowser feature on the phone. The pertinent section of ipmid.cfg is as follows: <microbrowser mb.proxy=""> <idleDisplay mb.idleDisplay.home="http://server/polycom/index.html" mb.idleDisplay.refresh="300"/> <main

Hi all, I have a Polycom Soundpoint IP 600 that looks like it is fried. It either has a bad or corrupt bootrom (I'm guessing). It never gets to the prompt that asks if I want to enter the setup configuration or continue booting. When plugged into power, it turns on, shows the Polycom logo for 3 seconds and then pretty much goes dead with two red lights on. The one in the top right corner

I just got a Polycom soundpoint and I set it up using the phone and web based admin. I cant seem to figure out the config files and they are confusing me greatly and I dont have time for it :) Some things are odd, like on every reboot it seems the volume I set is reset? is there any way to fix that. And the ringer seems low. - Even all the way up Anyone willing to point out a good asterisk

I've got a couple Shoreline IP phones, their Shoreline model number is Shoreline IP 100. I believe this is actually a Polycom SoundPoint IP 300 phone. I believe the phone is using a MGCP stack. I want to use it for testing with Asterisk. 1. I suspect I need to re-image the phone to make it work with *. 2. How can I preserve the current image on the phone? 3. What is preferred image to use

I'm attempting to set up my SoundPoint 501 with my Asterisk server. I've configured DHCP and TFTP and successfully updated both the BootRom and SIP application. I've also created a custom cfg file for this phone's MAC address and the settings seem to be taking just fine. I can see that the phone registers with my Asterisk server but 'sip show peers' reports that the phone

Hello all, I need the bootrom.ld file to set up some Polycoms I have Platform: Model=SoundPoint IP 330, Assembly=2345-12200-001 Rev=A I've publiched on my FTP files downloaded from http://support.polycom.com/PolycomService/support/us/support/voice/soundpoint_ip/soundpoint_ip330_320.html (3.2.3 combined and split zips) but my phones are still showing the message: "error, application is

I got em. You want em? Anyone know how I can get these to the site listed on the Wiki? Thanks, Wiley -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050512/dfee13b3/attachment.htm

I have a couple of Polycom phones, bootrom 2.5.0, SIP 1.3.1.0056. Works great with Asterisk when I power on the phone. However, after some time, say an hour, I cannot receive calls on this phone. On Asterisk, when I do "database show", it does show the phone in there, but it cannot reach the phone. Is there a way to keep alive the connection with Polycom? Any suggestions? Thanks, --

Hi Folks; I just bought a Polycom SoundPoint 500 off of ebay after having spent way too much time trying to get updated sip images for our cisco phones. The phone I bought didn't have an AC power adapter; Could someone please tell me the volts & amps that the dc plug that comes with the phone puts out? Thanks! Mike

Hi All, We are in search of the latest Polycom firmware SIP 1.6.5 and BootROM 3.1.3as per http://www.polycom.com/resource_center/1,,pw-492,00.html Can someone help? We have legitimately obtained these phones but even our official distributor can't get their hands on updated firmware. The only thing we have found is http://www.freedomphones.net/polycom/files/?M=A which has only old versions.

Hello all, Has anyone used the SIP version of this phone with Asterisk? I see Polycom has a H.323 and MGCP version also, does anyone know if you flash the phone to swith protocols? Thanks in advance for the info. Ed -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20031029/a9377305/attachment.htm

Hello All, I have some Polycom IP 500 phones that I would like to have configured for direct dialing to our voice mail system. So far I have been unable to get the hard button labeled Voice Mail to connect to Asterisk without first passing through the message center prompts. I have followed all the Admin Guide instructions regarding the phones .cfg files and using

I am getting ready to install Asterisk and I was looking into the Polycom IP600 phones. I spoke with Polycom sales to verify the multiple line appearance and they said it would work. More specifically, if lines 1-3 all contain the same SIP registration info, the Polycom will only send out 1 SIP registration to the server and then handle the calls ringing on multiple lines. I was wondering if

I am getting to my wits end with these phones (and so is my boss). I am getting an random echo on these phones and I have an issue opened with Polycom and its been in their research and development department for almost a month with no results. I have noticed that I get a message "RFC3389 support incomplete. Turn off on client if possible" in asterisk. I have researched this and made

I can't figure out how one upgrades the boot ROMs for the Polycoms. I've read the wiki, I've checked the docs, I've looked here, there, everywhere; I hoped it might be through the web interface, through DHCP... but I can't see how to do it. Suggestions? Thanks! -Ken

From what I know this log show everything working Perfect. Then it goes to the Welcome screen then after a long time of processing, it errors out with a 0x10000 error Any Ideas? 1005195711|so |4|00|---------- Initial log entry ---------- 1005195711|so |4|00|+++ Note that bootrom log times are in GMT +++ 1005195711|hw |4|00|Initial log entry. 1005195711|wdog |4|00|Initial log entry

Docs? Polycom has docs? Where would one find this fabled land of... err I mean Polycom does stating what ftp servers are supported? Doug. -----Original Message----- From: Ken D'Ambrosio [mailto:ken@jots.org] Sent: Tuesday, March 07, 2006 12:12 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Cc: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re:

List, I am having trouble with one of our IP600. Every five days or so, the phone locks up. This is the third 600 I have put in place. I am running asterisk 1.0.9. Has anyone had this problem with the IP600? This electronic message transmission, including attachments, is for the exclusive use of the individuals to which this e-mail is addressed and is to be reviewed and used exclusively

Hi We've setup an Asterisk PBX recently and I encountered the following problem: When [mac address]-registration.cfg file includes the FQDN of the Asterisk PBX for the Polycom SoundPoint 501 phones it will not (even try to) register with the Asterisk PBX unless the DNS (it asks) successfully resolves the name: _sip._udp.[Asterisk FQDN]. Did this happen to anyone else? PS - The

I have an extension setup in my extensions.conf for hold music. ext. 600. If I pick up a phone (polycom soundpoint 300 sip) and dial extension 600 I hear the hold music playing. If I call another extension and pick it up and put the call on hold with the hold button on the phone I hear nothing at all. Does anyone have any experience with these phones and getting the hold button to work?