similar to: X101P FXO with RED alarm

An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040913/52b2ac04/attachment.htm -------------- next part -------------- hi all, can anyone give solution for this. ?wct1xxp - Digium Wildcard T100P T1/PRI Card 0 zttool gives RED Digium Wildcard T100P T1/PRI Card 0 my zaptel.conf look like this span=1,1,0,esf,b8zs

Hi, I have been trying to get a Wildcard TE122 card running here the last couple of days. libpri and zaptel are all installed and configured to E1 specs. The jumper on the card is on, so configured for E1 (I'm in Norway). When running zttool, I get 'Alarms: RED' on the single card installed. Other information in zttool: Current alarms: Red Alarm Sync source: Internally clocked

I have a normal backup phone (and an alarm panel) sharing the POTS line with the Digium X101P FXO: | | Wall |>---+------X101P FXO as Zap/5 | | | Phone & Alarm Whenever the Phone is used, Asterisk sees a 'false ring' signal immediately when the phone is hung up. The Alarm panel dials out nightly at around 1AM, and each time it completes the call, Asterisk

can somebody that has these hardwares(X101P and S400P) working on his asterisk system please assist.................. you can send the solution to austino@skannet.com..... the error message is what i have below. ---------- Forwarded message ---------- Date: Thu, 1 May 2003 21:01:21 +0100 (WAT) From: austino@skannet.com To: asterisk-user@lists.digium.com Subject: Error working with X101P and

Hi, I installed a 1-port FXO on my Ubuntu 8.4. I was earlier only hearing a fast clicking sound and now I am not hearing any dial-tone. The FXO card has 2 slots: [phone | line ]. I hve connected the wall-phone-input to the "line" slot and "phone" to my home-phone. I do not hear any dial-tone on my home-phone. Asterisk seems to recognize my hardware....here are the relevant

I am having a problem with Red Alarms on X100P cards. The most frustrating thing is I can not duplicate the alarms, therefore am not sure how to solve it. I have read after searching posts and the web that you can try different signaling methods which may help alleviate the problem. There is fxsks (Which I am currently using), fxsgs, and fxsls While reading the Digium site about these different

Hello I'm using an older PC from 2000 that we have lying around at the office to learn about Asterisk using Pound Key 1.0.1 (http://www.rpath.org/rbuilder/project/asterisk/). It's using an AMD Duron 600MHz, a Gigabyte GA-7ZX motherboard, and two FXO Astralis X101P clones that I bought through eBay. Here are the three issues I have. Sorry, forgot the floppy with dmesg, lspci, and

Alarms Span RED wildcard X101P Board1 OK wcusb/0 0 ive got my asterisk server up and running and working correctly, the first time after a reinstall and reboot everything was fine - i had both alarms OK and i could get the USB extension ringing when i ran the house number from my mobile. as soon as i tried again i got a red alarm on the wildcard board. now im using the sample

Calling out on PSTN over a TDM400P seems to generate a Red Alarm - whatever that is. I have another extension on the PSTN, and I can dial out over that. zttool shows no alarms. asterisk*CLI> zap show status Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO Wildcard TDM400P REV I Board 1 OK 0 0 0 CAS Unk YEL 0 db

I'm having sporadic problems with my X100P card. When trying trying to call out I get a message on the console that the channel is busy even though I have bounced asterisk. It seems the card grabs the line and doesn't let go. When I try to call the number I get a busy signal. If I perform a rmmod wcfxo and restart asterisk everything retruns to normal. I have a TDP400P installed along with

Hi there, I've got two Asterisk hosted PBX servers with Digium TE210P cards attached by a E1 cable to Port 1 on each. On startup, both cards flash red, alternating between ports 1 and 2. When server #1 loads the Zaptel module and drivers, Port 1 status LED goes green. When server #2 loads the same module and drivers, Port 1 status LED goes completely blank. Unloading the wct2xxp

Hi, Has anyone got the X100P to work with an anlogue line in the Republic of Ireland? I have the X100P installed but zttool indicates a Red Alarm status on the card. It is on its own interrupt and I have tried different PCI slots but all to no avail. Are there any alternatives to the X100P that can work with asterisk and are likely to work in Ireland? Thanks, Aaron

(to mods: sorry for any extra work I've put you through. Posting from my work account, as proper) Hello all, I'm back. I've got that lucky feeling that this will all work out very soon, and I hope that that is true. The issue: In my * server I have a t100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm

Wow ! No reply... May be I must talk about X100P instead of X101P ? Is someone has yet encountered this kind of "no sound" problem when bridging two FXO lines like this (first as input, second as output) ? Any idea ? TIA. Best Regards, Francois BERGERET, France. ----- Original Message ----- From: "Francois BERGERET" <f6hqz-m@hamwlan.net> To: "Asterisk Users

Hi I'm having difficulties getting up my TE110P (running as a E1) when I connect it to the PRI. If I start the server with a loopback connector everything seems fine and the led is green but when I connect it to the PRI the flashing starts .... I can't seem to find anything in the log that suggests what could be wrong .....Aug 8 11:33:00 DEBUG[1369]: Updated conferencing on 31,

When x101p clone receive ring signal from phone line, my voip phone start ringing. But, if caller hang-up at some time, phone continues to ringing 10 second more. How can I shorten that time? Pause betwen incoming rings on my phone line is 4s, so when x101p clone (wcfxo driver) do not receive next ring signal after 4.5 sec, call should be consider as ended. What should I change to set that time

An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040810/16371a21/attachment.htm -------------- next part -------------- ? Hi, I'm using TE410P card with four T1 lines. I've configured all the channels in my /etc/zaptel.conf file. In zttool i'm getting "OK" for the "Span-1" but the other three spans giving

Folks, I'm experimenting with bringing multiple (8) analog lines from our local telco into a Carrier Access ADIT 600 channel bank with an FXO module, then having this talk to Asterisk via the T1 TDM controller on the ADIT and a TE405P card. I don't know if this will work well (ie: give me decent echo cancellation, call disconnect supervision, caller ID etc) but I haven't had much

Perhaps everything isn't as spiffy as I thought When running zttool the card still reports as internally clocked Zaptel.conf: # Global data span=1,1,0,ccs,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 loadzone=se defaultzone=se And as pointed out by Peter I do get a lot of D-channel warnings ... Aug 9 16:21:25 NOTICE[1350]: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 And

Dear members of the list, I have difficulties to obtain sync with a Digium TE420 PCI Express For four entries E1, In my case I am with only 3 E1s available to configure. The telephony operator is BrasilTelecom and Signaling is R2 Digital. The information I have is that are E1s with 32 channels, not have sure. My settings Have been based on the link reference: