similar to: Asterisk rxfax(): One page gets two pages

I'm trying to install the RxFax in Asterisk. After much trouble getting app_rxfax.c (and friends) compiles and installed into Asterisk (thanks to the many asterisk-users messages) it did get it installed. I have been unable to receive a legible fax. app_rxfax provides lots of debugging information but none useful to me. I was hoping that someone has an idea what might be going on.

Hi, I just sent this to Steve Underwood, but then found a bunch of posts on the mailing list about similar issues.. does anyone have the fix? I'm running asterisk CVS-HEAD-06/28/04-18:13:13, spandsp 0.0.1k, libtif 3.5.7 one thing i just noticed is that calls come in with format '72' which is G711A-law or LinearPCM.. it uses PCM for the call, i assume this is ok the results of RxFAX

On the /proc/zaptel it was lost interrupts, you haven't got any so that's good! On opencall.org there's a known issues link and that mentions some fax machines that have issues, might be worth a quick check there. I can receive from our fax machine this end, if you'd like I'll send you a test fax if you send me your fax number, if you can receive from us and tpc then it's

>From couple of weeks i am working on asterisk fax but was not successful. I am able to receive only half fax documents and its ending with blurred lines. I have tried with almost all the versions of spandsp 0.0.2pre4,pre10 etc but of no use. I have digium card to which i have plugged in 2 pstn lines and i have removed echocancellation too(zapata.conf) and also enabled g7111 alaw&Ulaw

more detailed output Sep 21 15:54:31 DEBUG[1120357296]: pbx.c:1255 pbx_extension_helper: Launching 'RxFAX' Sep 21 15:54:31 DEBUG[1120357296]: channel.c:1699 ast_set_read_format: Set channel Zap/1-1 to read format SLINR Sep 21 15:54:31 DEBUG[1120357296]: channel.c:1666 ast_set_write_format: Set channel Zap/1-1 to write format SLINR Changed from phase 0 to 1 Slow carrier up Slow carrier

Sorry to bore you more with the clock issue, but have you check /proc/zaptel/<span> to make sure it's not missing interrupts? There's also an option to record the audio for the fax, you could listen to that vs a recorded file that will receive correctly on a fax machine and see whether there is an obvious difference? (Good luck, that'll be really scraping the barrel!!) Does it

I'm running asterisk CVS HEAD from 20040601 with spandsp 0.0.1k and libtiff 3.6.0 (no other copies are installed). I've put the audio files up at http://www.mixdown.ca/~andrew/dump/akohlsmith-faxsegfault.tgz -- the machine I am faxing from is a Canon IR3300 printer/copier/fax, but I get similar crashes from $29.95 fax machines too. :-) I'm trying to get a decent backtrace but

Initial handshake sounds fine, but asterisks dies before receive of the fax. Here is the log : Changed from phase 0 to 1 Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow

Rxfax answers, makes handshake, and crashes once the page starts to send. It receives a .tif file of 8 bytes. Asterisk dumps core - gdb shows : #0 0x281fd86c in t4_rx_putbit () from /usr/local/lib/libspandsp.so.0 #1 0x281fea3c in fast_putbit () from /usr/local/lib/libspandsp.so.0 #2 0x28208324 in decode_baud () from /usr/local/lib/libspandsp.so.0 #3 0x2820893f in process_baud () from

Dear Steve i have try SpanDSP from the first version to the last one (1k) with my Canon FAX and with my modem but every time i see a lot of message like this: ----- I send a Fax from my Canon B150 i have the following error: -- Starting simple switch on 'Zap/33-1' -- Executing RxFAX("Zap/33-1", "/home/user/testfax.tif") in new stack Changed from phase 0 to 1

I've seen people mention that they have fax reception working with Asterisk, spandsp, and app_rxfax. I'm using the latest Asterisk from CVS, SpanDSP 0.0.1k, and the latest app_rxfax.c (as mirrored by friendly list members recently), and libtiff 3.5.7. Asterisk is detecting the fax signal properly, and executing the fax extension in the dialplan. The fax part of the dialplan is pretty

I use http://www.voip-info.org/wiki-Asterisk+callingcard You only should compile the prepaid.c (look at readme file). Regards. Julio ----- Original Message ----- From: <clive18@webmail.co.za> To: <juliom@telelinkusa.net> Sent: Tuesday, April 20, 2004 12:47 AM Subject: fwd:Re: [Asterisk-Users] Asterisk prepaid debug > Hi > > Which pre-paid app are you using?. > Is it

I am also having problems receiving my first fax. I get a 320byte file (for a 4 page fax). If I look a the tiff generated, is just has some few dots. I am sending the fax from a notebook with Windows XP to an X100P and using libtiff v3.5.7. Has anyone successfully received faxes ? Output to the console as follows: Changed from phase 0 to 1 > Start receiving document > Changed from

Hello, I tryed out spandsp with libtiff-3.5.7 and with Asterisk from CVS. I tryed to receive a fax on a CAPI channel. Finally I got a file with 8 byte length (/tmp/testfax.tif). How can I do next? Thanks in advance, Thomas ps: what are hardware requirements for sending/receiving faxes? -- creating pipe for PLCI=0x101 msn = 2258589 > sent ALERT_REQ PLCI = 0x101 --

Dear Steve after a lot of compile from spanDSP first version to K and after i have compile * HEAD and Stable i cant understand where im wrong... - Mandrake 9.2 - libtiff3-3.5.7-11mdk I have add Header from your FTP but the result is this error.. Can you give me your opinion? Thanks in advance Dimitri -------- -- Executing RxFAX("Zap/35-1", "/home/user/testfax.tif") in

I am having a problem with SpanDSP. What happens is when I send a fax to SpanDSP the fax message seems to fail in the training phase. I think it's a timing error, however I have no idea about how to rectify the problem. I have included a copy of the log below. I am using a Digium TDM-400P card with 2 x FXO ports and 2 x FXS ports. The fax is connected to one of the FXS ports (Zap3). The

I am having a problem with SpanDSP. What happens is when I send a fax to SpanDSP the fax message seems to fail in the training phase. I think it's a timing error, however I have no idea about how to rectify the problem. I have included a copy of the log below. I am using a Digium TDM-400P card with 2 x FXO ports and 2 x FXS ports. The fax is connected to one of the FXS ports (Zap3). The

Hello All ~ Having problems sending and receiving faxes with SpanDSP. I am testing on a simple 2 analog POTS to 2x X100p set up, connecting one line to a Konica 720 fax machine to test, or with other remote fax machines. Voice calls are working pretty well now. Platform is P3/800MHz/256MB/FC1. * recognizes faxes, and passes calls to RxFax and TxFax OK, but 99.9% of the time no fax content is sent

I'm getting the following when sending to a specific fax machine. Any ideas? File name is '/var/spool/asterisk/email2fax/7F2SOeYJiU.tif' Changed from phase 0 to 2 Slow carrier up Slow carrier down Slow carrier up <<< NSF: 20 00 00 11 80 00 8a 49 10 53 54 49 52 4c 49 4e 47 20 43 4f 56 49 4e 47 54 00 67 00 80 80 80 0c 01 02 NSF without final frame tag The remote is made by

Hi, I'm trying to send a fax from a Zap channel to another Zap channel and I can't - below the logs. How could I solve this? Thanks! In RECEIVER: -- Accepting call from '' to '1980' on channel 0/2, span 1 Urgent handler -- Executing Answer("Zap/2-1", "") in new stack Urgent handler Urgent handler -- Executing Goto("Zap/2-1",