similar to: TE405P + Adit 600 and FXO module - should this work?

Folks, I've been following recent discussions regarding echo and echo training with much interest, since it's a problem we've never been able to eliminate here. We're facing two challenges presently, and they may be related (or not): a) Cisco 7960s in the office here echo back to our staff, but the customer hears decent sound. b) We've yet to be able to pass faxes through

We're having some difficulty connecting a T1 fax board card to asterisk, with E&M Wink. We've successfully connected it to other E&M Wink T1s, but have been unable to get asterisk to hear it's dialing. Asterisk can dial down to it with no problem, and it hears all the digits, but whenever it sends digits down to asterisk, * always only "gets" the first one. This is

What kind of channelbank/FXS port are you connecting to? I've seen problems connecting to some of the older versions of the Adtran Total Access 750's. I wouldn't doubt there would be problems on other channelbanks with older firmwares. Of course, no firmware on CAC AB1's I have the AAstra 480, Adtran 750 Channelbank (updated firmware), T100P card, and it worked fine on the

Hi, I would like to set up a high density FAX/PBX server, am looking at using Eicon Diva E1 card with Asterisk and Hylafax sharing channels, is this possible. I know Extensions can be reserved for voice OR fax with the combination of chan_capi used for * voice, capi4hylafax on fax but then channels must be dedicated rather than shared ie. would like to be able to answer voice/fax on same DID.

I have an adit 600 with one fxo card connected to a Digium single span T1 card. CallerID, disconnect supervision work perfect, however the users complain that they have some sound quality issues, after testing it I realized that whenever one is in a phone call they get like silence between the sounds coming from the other party, almost like a cell phone, in other words if there is no sound coming

What are your experiences with faxing through Asterisk to the PSTN? We are using g.711u as a codec, and are originating/terminating with Broadvox as well as through our own PSTN gateways. We have had some luck with incoming faxes coming into our network from Broadvox DIDs. They work 50% of the time. Not sure yet on PSTN incoming since nobody that is using FAX is in our local rate centers.

I've searched but can't find an answer as to how many MGCP paths can a single ADIT/CMG card support? It appears it's only 24 ports, maybe 48. What I'd like to do is install 6 Telco T1's into a single (or more) Adit 600 and route inbound calls towards asterisk. Can I have more than one CMG in a single chassis? Or maybe you know of a better way to connect T1's to

I just installed the new version of SJPhone and it appears that it cannot work with * anymore? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040111/25c910bb/attachment.htm

T.38 is often put forward as the solution for reliable FAX over VOIP. Just wondering for anyone using T.38 (with any equipment), how well does it work as compared to a FAX PSTN call? Thanks. Jim James H. Thompson jht@lj.net -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20041129/3ea08b2c/attachment.htm

Asterisk apparently has five echo cancellation algorithms: STEVE, STEVE2, MARK, MARK2 and MARK3. The current default appears to be MARK2. My question is, has anyone had any experience with any of the others (other than MARK2), and is there some conventional wisdom as to when to use one over another? TIA Bruce Komito High Sierra Networks, Inc. www.servers-r-us.com (775) 236-5815

Hello, I have spandsp setup to accept incoming faxes and receiving tif files via Email. Using tiff2pdf, or tiff2ps -a2 or even tiffsplit, the last page of the fax is cut off and the quality of the text looks "squished". I "figure" it's a tiff parsing thing, as opposed to a problem with my spandsp installation (heh). Has anyone experienced the same thing, or can

I am hoping to replace my Nortel 8x24 switch with Asterisk. Right now my cabling comes from my outside phone box into my office and into a punchdown block and leaves the punchdown block as an amphenol connector which currently plugs into the Nortel swicth. A second amphenol connector them plugs into the switch and extends to another punchdown block that I believe carries the lines throughout the

I have an adit 600 with an fxo card connected to a digium T1 card. If I try to make an outgoing call and the T1 cable is disconnected, asterisks returns congested like it should. But, if the adit 600 is connected to the T1 card, the adit 600 immediately "answers" the call even if there are no physical lines attached. I even removed the fxo card and the adit 600 still

I've been reading the Google searches trying to understand how to tie together Adit 600 to Asterisk to provide 2 way service. I'm about blind from reading. I assume, the answer is using MGCP between the boxes. However, the examples I found don't really explain fully enough to know how to modify examples to work for me. I'll have in the ADIT with T1's. There is a CMG and

Ok, I've pretty much decided to try the Adit route. Somebody who has experience with these tell me if I'm missing something. I have 15 incoming PSTN lines. T1 is not an option at current location. I want to put in an Adit 600 with 2 8-port FXO boards. The adit will then connect to * via a digium t1 board. I configure zaptel.conf for the T1. What other parts would be needed? How do

Has anyone had any success using the Adit 600 with the CMG card talking MGCP to asterisk? I want to have a central asterisk server with 10 Adit 600's at various locations providing 24 FXS ports.... Thanks, Isaac

I'm trying to get a Carrier Access Corp. Channel Bank I working with a Digium T100P without success. What is stranger is that the status lights on the channel bank and T100P seem to change almost each time I power cycle the channel bank or reset the T100P. The channel bank has three status lights: T1, Framing, Status. T1 is green, Status is yellow, and Framing is usually red but sometime

Hi ! I am connecting to Adit 600 thru a T100P card I have configured 1-16 FXS channels and 17-24 FXO. Everything looks fine on Asterisk side I get a tone on all FXS channels, but when I try to dialout thru one of the FXO channels 17-24 it doesn't connect to the POTS line and echoes back my voice. I use fxsls and fxols for the T1 channels and ls on Adit side. Whats wrong here ? here is my Adit

Hi, I'm using an Adit 600 Channel Bank with *. I love it and it works really great for my FXS lines. One problem that I have with it (It's really not a problem yet, but it's a potential one) is that I've scoured the manaual for the Adit to see if there's a way to dump out a config file from the bank so in the event of a power and battery failure I don't have to type in the

I know a few ppl have those CAC Adit 600's with t400 I can't seem to get my second span up on the T400 connected to the second spand on the adit (A:2) A:1 seems ok Can someone post they zaptel.conf span defintions And maybe a "print config" from the adit 600 cli I think my issue is timing srcs the coding, framing. bld out are all matched thx -------------- next part