similar to: Channel Bank Woes...

Hi ! I am connecting to Adit 600 thru a T100P card I have configured 1-16 FXS channels and 17-24 FXO. Everything looks fine on Asterisk side I get a tone on all FXS channels, but when I try to dialout thru one of the FXO channels 17-24 it doesn't connect to the POTS line and echoes back my voice. I use fxsls and fxols for the T1 channels and ls on Adit side. Whats wrong here ? here is my Adit

I have an adit 600 with one fxo card connected to a Digium single span T1 card. CallerID, disconnect supervision work perfect, however the users complain that they have some sound quality issues, after testing it I realized that whenever one is in a phone call they get like silence between the sounds coming from the other party, almost like a cell phone, in other words if there is no sound coming

Folks, I'm experimenting with bringing multiple (8) analog lines from our local telco into a Carrier Access ADIT 600 channel bank with an FXO module, then having this talk to Asterisk via the T1 TDM controller on the ADIT and a TE405P card. I don't know if this will work well (ie: give me decent echo cancellation, call disconnect supervision, caller ID etc) but I haven't had much

HI, I have been pulling my hair out trying to get a Cisco MC3810 to interface my Asterisk box with a T1. I am able to make outgoing calls but incoing calls never reach my Asterisk box. The cisco give a fast busy when I try to call one of the DID's. When playing around with the dial-peers I can get the cisco to pick up the call, but then it forwards the call back to the ANI that is dialing.

Hello, I have an Adit 600 (3 FXS cards) hooked up to a digium T1 card in my asterisk box. I 'connected' the slots to the a:1 T1 interfaces via the command line. The slots (3 fxs) are configured with 'ls' signaling. I configured the T1 card with the same line settings as the T1 interfaces on the adit and I get green lights on both the T1 card and the T1 interface on the adit (so

Hi, I am experiencing one-way audio from: SIP Device ----> Asterisk -----> Cisco 7200 The Cisco 7200 has a VXE+ card that will allow you to do SIP. I can pass audio from SIP Device to Asterisk through the Cisco 7200 to the other end, but the Cisco 7200 does not return any audio back to the SIP Device or Asterisk, it seems. I have tried upgrading to 12.3T IOS version, but no

I have the following configuration: CLEC -> T-1 -> Asterisk -> Adtran Channel Bank -> (analog) -> Nortel Don't complain that it's ugly. I've already done plenty of that. The CLEC manages their Adtran remotely and needs to be able to continue to do so. I assume they use FDL to do the management. We are using the Zaptel DACS/DACSRBS to cross connect some of the

Hello, I've recently purchased Adit 600 with 3FXS and 1FXO to be connected to my * server via T100P card. This is the output of "status equipment" command in the Adit600: For some reason the FXO card is seen as FXS, why? Is it ok? On the card it is written "FXO". Regards, Shlomi Bachar -------------- next part -------------- An HTML attachment was

I have a file in stata format, which I have read in, and I am trying to create a text file. I have exported the data using various delimiters, but I'm unable to read it back in. I originally read in the file with: library(foreign) myData <- read.dta("mydata.dta") I then exported it with write.table using comma, tab, and exclamation marks as a delimiter. When I was unable to

Hi, this is to inform everybody that the translation of my new book (unstable version) is online at http://www.the-asterisk-book.com The book is a GNU FDL project. So everybody who wants to participate is welcome to do so. Also, everybody who needs material for his own work, feel free to take it as long as the new material will become GNU FDL too. I am glad that Stephen Bosch (who you

On Sat, Dec 11, 2004 at 07:37:40PM -0500, Helen Glazer wrote: > As is my routine every couple of weeks, I ran Pest Patrol anti-spyware > software, and was disturbed to find it came back saying that the file > FLAC/COPYING.FDL was a security exploit known as "Virus Tutorial" or > VTool/jul2. This has left me wondering if FLAC is to be trusted. Well, since the file in

I am a little confused about the FXO ports on the Carrier Accesss Bank 1. The wiki, and people on the mailing list have stated that they do not have impedance matching, but Carrier Access states in their documentation that they do have impednace matching. Did Carrier Access make a typo, or does it depend on the version of the FXO card? I current have a CAC AB1, and I am having echo problems

Jon, I actually had some more discussions with Tim on this issue, and it seems that the channel bank would still be a good option to choose for internal purposes. I would not see any other solution than a channel bank to connect many 2wire phones into one asterisk box. I had a talk today with Carrier Access, and it seems that the adit would do us fine. The fxs cards of the adit 600 are

Peter - 40 phones and only 3 PSTN trunks?. I would recommend at least 2 BRIs for this. If you have ISDN you can also get DDI to the extensions.I would strongly recommend abandoning the analogue PSTN lines and using ISDN. The setup pain you will go through will be significantly less, combined with better audio, more features (like DDI numbers!) and much more robust connections. You should look

As is my routine every couple of weeks, I ran Pest Patrol anti-spyware software, and was disturbed to find it came back saying that the file FLAC/COPYING.FDL was a security exploit known as "Virus Tutorial" or VTool/jul2. This has left me wondering if FLAC is to be trusted. Here's what PestPatrol's web site has to say about it: Exploit: A way of breaking into a system. An

We are currently working to trunk from a Nortel 81C to an Asterisk Server 1.4 running on Red Hat Linux. We have two PRI trunks which work with the exception of the clock slips, which is causing the Nortel to reset the PRIs once a hour. Thanks for any suggestions. 81C MSDL Asterisk Digium TE110P REQ prt TYPE adan dch 10

I have a data set like this ID=c("A","A","A","A","A","A","A","B","B","B","B","B","B","B") s=c(1.1,2.2,1.3,1.1,3.1,4.1,4.2,1.1,2.2,1.3,1.1,3.1,4.1,4.2) d=c(1,2,3,4,5,6,7,1,2,3,4,5,6,7) t=c(-3,-2,-1,0,1,2,3,-3,-2,-1,0,1,2,3)

Not all archs have the __io_virt() macro, so cirrus can't simply convert pointers that way. The drm format helpers have to use memcpy_toio() instead. This patch makes drm_fb_memcpy_dstclip() accept a __iomem dst pointer and use memcpy_toio() instead of memcpy(). With that separating out the memcpy loop into the drm_fb_memcpy_lines() helper isn't useful any more, so move the code back

I have a data set like this ID=c("A","A","A","A","A","A","A","B","B","B","B","B","B","B") s=c(1.1,2.2,1.3,1.1,3.1,4.1,4.2,1.1,2.2,1.3,1.1,3.1,4.1,4.2) d=c(1,2,3,4,5,6,7,1,2,3,4,5,6,7) t=c(-3,-1,0,1,2,3,4,-3,-2,-1,0,1,2,3)

Hello, I don't have any experience with channel banks and would appreciate any feedback on my theory outlined below: We have a single T1 entering the building with channels 1-12 being voice lines and 13-24 being a 768k internet connection. This T1 terminates to an Adit 600 (T1-1). Here's what I know. Channels 11-12 go out the Adit 600's 25-pair connector to a wiring block (and