similar to: tdm400p + x100p config problem

Hello. Well I finally rx'd my dev kit (new batch of TDM's apparently. I'm on Mandrake 9.1 There were no hardware install instructions, it would have been nice to know whether the 4-way power connector was to be used or was for some other future or expansion purpose. It came with a floppy disc, no label and it wasn't even write protected. The only readme file was

Hi All, Sorry if this has been around a millions times.. I have been off this list for a few months now.. I have installed the latest asterisknow (upgraded asterisk to 1.6 as well) and I am having a hard time getting my X100P and TDM400P working.. Its all new to me with dahdi because my old server is still running Asterisk 1.0.2 so there have been lost of changes.. Can someone point me in

Hi , I have an asterix (1.2.7.1) box with 3 TDM400P and 10 FXO modules, and zaptel (1.2.5). The problem is that 6 modules can't be initaized and i get the folowing error: May 7 09:17:37 WARNING[7739] chan_zap.c: Unable to specify channel 9: No such device May 7 09:17:37 ERROR[7739] chan_zap.c: Unable to open channel 9: No such device here = 0, tmp->channel = 9, channel = 9 ztcfg output

Hi, I just got my TDM400P card (2 modules) and i installed it no probs. The card is detected fine, but for some reason when I add the card to zaptel.conf i get the following error: --snip-- ZT_CHANCONFIG failed on channel 2: Invalid argument (22) Did you forget that FXS interfaces are configured with FXO signalling and that FXO interfaces use FXS signalling? --snip-- My /etc/zaptel.conf looks

Hi, I have received a new card TDM400P revision E, from digium. When I tried to modprobe wcfxs it gave me the following errors: Freshmaker version: 63 Freshmaker passed register test ProSLIC on module 0 insane (1) 255 should be 2 Module 0: Not installed ProSLIC on module 1 insane (1) 255 should be 2 Module 1: Not installed ProSLIC on module 2 insane (1) 255 should be 2 Module 2: Not installed

Hi when I turn on my PC I able to load the drivers and start my card, if I reboot the PC I have the following error ztcfg -vvv Zaptel Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) Channel 03: FXS Kewlstart (Default) (Slaves: 03) Channel 04: FXS Kewlstart (Default) (Slaves: 04) 4 channels

Hello, I am having problems configuring a TDM400P 4 Port FXO card with groundstart signalling. The box has 2 X100P's, 1 TDM04B and 1 TDM40B. I can configure it for loopstart and it works, just not groundstart, which I need for this installation. What am I missing? Thanks! Mark /etc/zaptel.conf #two X100P FXO Cards # fxsls=1-2 # TDM400P 4 Port FXO (TDM04B) fxsgs=3-6 # TDM400P 4 Port

Hi All, I recently installed and compiled Asterisk in a Red Had (enterprise) box with digium TDM400P card installed in it. Thanks to the good documentation available, I was able to install and configure the hardware as well as software. As specified in the Getting Started with Asterisk Guide, I first installed zaptel driver, then libpri and finally Asterisk. All of them successfully compiled, but

This has got to be a stupid error I'm making... I have been experimenting with different hardware and software configurations before I decide what to use as a production platform. Up until just recently things were going well. But now it appears I'm unable to get access to my TDM400p from Asterisk. I know the TDM card works fine, used it in another machine where it performed flawlessly.

Hi there, I have a TDM400P (1 x fxs, 1 x fxo) which I'm attempting to run on linux 2.6 (gentoo), without much success at the moment. I have previously had it working on a 2.4 installation, but when I moved to a new box and installed a 2.6-based system, it failed to work. In both cases I'm using whatever (libpri, zaptel, asterisk) is checked out by default (I assume that means HEAD)

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

Hello all! I have tried and tried to resolve this one to no avail. Hopefully one of you can help... The system in question is a Compaq Evo D600 (iirc) business desktop, with a 1.4GHz Pentium 4 and 512mb of RAM, running a stock install of PoundKey 1.2. It has two Digium cards installed: a TDM400P with four FXO modules, and a TE110P hooked to a Carrier Access Adit 600 which serves 8

I am putting together my first *. I had it running with two other pc's running xlite and setup voicemail and a couple of menus and submenus and had that running well. I had order a couple of oem x100p cards from digitnetworks. I installed them as they said with their voicepet2.2.zip drivers and did the modprobe on zaptel and wcfxo and then ran ztcfg -vv and got this: Zaptel Configuration

sorry to bother with this trivial issue, but i am loosing all my hair ;-) got 2 x100p's and * on a slakware box x-lite to x-lite works fine! i also have: #ztcfg -vvv Zaptel Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) 2 channels configured. and in extensions.conf i got: [locals] exten

I've got the latest zaptel and cvs asterisk software loaded on my phone server running FC3. And yes, It's fully updated and udev is setup correctly. I've got a TDM400P with one FXS and one FXO module installed. When I load zaptel and wctdm and run ztcfg -vvv, I get this: [root@asterisk ~]# ztcfg -vvv ZT_CHANCONFIG failed on channel 1: No such device or address (6) Zaptel

I think I have a bad FXS module on my TDM400P. Channel map: >> >> Channel 01: FXO Kewlstart (Default) (Slaves: 01) >> Channel 02: FXS Kewlstart (Default) (Slaves: 02) >> >> 2 channels configured. >> ZT_CHANCONFIG failed on channel 1: No such device or address (6) The zaptel loads ok, but the wctdm reports No such device or address and stays loaded. The

Hi, Thnx to all, actually I didn't red the installation instruction paper properly that came with the card, and it was written on it as step 4 to insert the power cable in the card. Now the drivers are loading without any error. Azher --------------------------------- Do you Yahoo!? Yahoo! SiteBuilder - Free, easy-to-use web site design software -------------- next part -------------- An

I installed the TDM400P and installed it on a system running on Fedora Core1, please refer to the steps below. I connected an analogue phone to the FXS port. When I pick up the speaker I don't hear the dialtone although when I press a number key I hear a DTMF generated. What could be the problem? I appreciate your help 1- First I installed the TDM400P in the PCI slot and connected

Hi, I bought the Digium Asterisk Developers kit a few weeks ago, got the x101p and a tdm400p cards, both seemed to be working fine up until today, now the tdm400p seems to have gone to the great PBX in the sky ...... If I left the reciever on the analog phone I don't get a dial tone and nothing appears on the asterisk console, If I use my cellphone and dial in I see Asterisk Ready.

Hi, I have installed a TDM400P in a PC which runs RedHat Linux 3.2.2-5. There is an FXS module connected to the first slot of TDM400P and an FXO module connected to the fourth slot. This card is detected by the operationg system, which I was able to make sure using the output of lspci command. I modified the configuration files zaptel.conf, zapata.conf and extensions.conf. When I execute the