similar to: How to determine line signalling?

It would be nice if Digium updated the hardware compatibility list on asteriskpbx.org to indicate that the LineJACK can't be used for dialing out. I've seen several people on IRC be burned by not knowing this. --Eric -- BTEL Consulting 850-484-4535 x2111 (Office) 504-595-3916 x2111 (Experimental) 877-552-0838 (Backup Phone)

Anyone know what model and what support the new $100 Cisco has? http://biz.yahoo.com/djus/030428/1030001060_1.html -- Steven Critchfield <critch@basesys.com>

And it runs linux. http://www.zip4x4.com/ZIP4x4.htm Anyone seen one? bkw

As I understand it (and my understanding is obviously incorrect) the switch => statement sells the Asterisk box to resolve (aka lookup) extensions by querying the remote Asterisk server defined in the switch => statement. The switch => statement is used to centralize dialplans. I've not used the switch => statement yet, I'm just trying to understand the ramifications of using

I've made some major changes to the way Asterisk handles file formats. I'd like feedback from people about any experience they have with these changes. They *may* improve playback performance for people who have had trouble with playback performance in the past. Mark

Maybe its just me but I find this question a little confusing, the tone duration should have no impact on tone recognition and typically in my experience the duration of the tone is defined by how long the user holds down the button !? > -----Original Message----- > From: James Sizemore [mailto:james@deny.org] > Sent: 22 August 2003 17:33 > To: asterisk-users@lists.digium.com >

Hello, I am having problems configuring a TDM400P 4 Port FXO card with groundstart signalling. The box has 2 X100P's, 1 TDM04B and 1 TDM40B. I can configure it for loopstart and it works, just not groundstart, which I need for this installation. What am I missing? Thanks! Mark /etc/zaptel.conf #two X100P FXO Cards # fxsls=1-2 # TDM400P 4 Port FXO (TDM04B) fxsgs=3-6 # TDM400P 4 Port

I get the following message when I dial 74#. Does anyone have any ideas on what might be going on? If I don't require numbers to be terminated with # everything works as expected, but you have to wait for the digit timeout, of course. MESSEGE: DEBUG[1150520624]: File pbx.c, Line 1683 (ast_pbx_run): Oooh, got something to jump out with ('#')! -- Invalid extension '#' in

I'm getting the following message when I start Asterisk: WARNING[1024]: File codec_g729b.c, Line 413 (load_module): Unable to initialize va stuff: -1 Did I mess up the registration key or is something else wrong? --Eric -- BTEL Consulting 850-484-4535 x2111 (Office) 504-595-3916 x2111 (Experimental) 877-552-0838 (Backup Phone)

Licensing info for the G723.1 codec, direct from the holding company that licenses the codec. http://www.dspg.com/technology/LicensePricing.html As you can see they want a LOT of money. This is why I doubt there will ever be G.723.1 codec available fro Asterisk. -- BTEL Consulting 850-484-4535 x2111 (Office) 504-595-3916 x2111 (Experimental) 877-552-0838 (Backup Phone)

Is there any way on the iaxtel.com web site to see if my asterisk is registering and what 700 number is associated with my iaxtel account? I registered many months ago but never used it. My asterisk shows registered, but I can't seem to receive any calls (callers get a the user is not registered message) -- BTEL Consulting 850-484-4535 x2111 (Office) 504-595-3916 x2111 (Experimental)

I received a message from Packet8 last night telling me they added some new area codes. I took a look at their new area code/rate center finder page and it looks like the added a LOT of new area codes. They now have phone numbers available in almost every state. The URL for finding out which area codes and rate centers are available with Packet8 is at http://www.packet8.net/about/areacodes.asp

Hi again, I'm trying to setup our non pri T1 (they call it a Long Distance T1), our current pbx has the signaling set to E&M, I can set em in zapata.conf, but I'm trying to track down the proper entries for the zaptel.conf file. The digium docs only show a PRI example. Our current system has these settings: Signalling: E&M Framing mode: ESF Line Coding: B8SZ here's my

I use the following macro for my extensions. It only works with Zap channels and assumes that any Caller*ID number that is 4 digits is an internal call and all other calls are external calls. Use like this: exten => 1234,1,Macro(std-exten,Zap/4,20) [macro-std-exten] ; ; Caller*ID is 4 digits (internal call) ; exten => s/_XXXX,1,Dial(${ARG1}r2,${ARG2}) exten =>

This is with an x100p (the motorola chipset) Two problems. Looks like CALLERIDNAME is being used uninitialized. On my other phones the callerid is fine and my buttset shows that the callerid passes the checksum. This is the relevant portion of extensions.conf exten => s,1,Answer exten => s,2,SetCallerID(H ${CALLERIDNAME} <${CALLERIDNUM}>) exten => s,2,Dial(${MGCP_ALL}) Here is

Hi there! Has anyone succesfully used a Cisco 12 SP+ with *? If so, how did you do? I'v not even tried, but before trying I thought I could bug you somewhat. =) //Filip

Am I the only person in the * world who can't get a sip connection through an iptables firewall? I've got everything else working fine. Xten <-> PSTN, Xten <-> Analog, IAX <-> IAX, but exten => 3733,1,Dial(SIP/fred@somewhere.com) ; evades me, ngrep @ port 5060 says the INVITES go out but how do I get something back? -- Dave Cotton <dcotton@linuxautrement.com>

Here's a patch that changes the behaviour of # transfers in asterisk. A single # is transferred to the remote phone/system. Two # in quick succession will trigger a transfer. This is very useful for users who have basic analogue phones connected to an ATA 186. For example, when calling a remote conference or IVR system you often want a single # to be sent to the remote system - not to

Hi All, Is there any way to connect (register, initiate and receive calls) with Asterisk to FWD through NAT? Since I own my router port forwarding is not a problem. I tried with Register => <FWDnum>@fwd.pulver.com:<FWDpass>@fwd.pulver.com but since Asterisk still use internal IP in some SIP fields I got "479 We don't accept private IP contacts. Please set your external

I'm looking to implement some basic CLASS features, using my own dialplans as well as those so thoughtfully contributed by "The Traveller" a few weeks back. However, instead of building my own dialing sequences (*69, *67, etc. etc.) for these features, I went looking for the standard list of CLASS dialing codes. I found this