similar to: help with pri configuration..

Hola! I've a Digium E1 card, zaptel recognizes it as (loading the module with debug=1) Setting up DMA (write/read = 321b2000/321b2200) Controller version: 43 Framer: DS21554, Revision: 5 (E1) Found a Wildcard: Digium Wildcard E100P E1/PRA Using CCS/HDB3 coding/framing with CRC4 120 Ohms Calling startup (flags is 4099) Started DMA Got interrupt: 0x0005 /etc/zaptel.conf:

Hi guys, I've been installing and configuring a TE110p card. The compile and install went very well. I'm using this on FC4 and I compile with linux26 as well checked I on the udev configs. zttool and ztcfg both indicate that the card is ready. But when I try to "load chan_zap.so" then I get the following Unable to load module chan_zap.so Jan 5 21:43:33 ERROR[6808]:

I have configured /etc/asterisk/zapata.conf, but now Asterisk refuses to start: Aug 5 10:47:29 ERROR[1076842624]: chan_zap.c:5976 mkintf: Unable to get parameters Aug 5 10:47:29 ERROR[1076842624]: chan_zap.c:9478 setup_zap: Unable to register channel '1-15' Aug 5 10:47:29 WARNING[1076842624]: loader.c:328 ast_load_resource: chan_zap.so: load_module failed, returning -1 == Unregistered

Hi, I buyed a wildcard e100p and I installed that but when I load asterisk I have this error: Apr 29 18:59:25 WARNING[8192]: chan_zap.c:690 zt_open: Unable to open '/dev/zap/channel': No such device Apr 29 18:59:25 ERROR[8192]: chan_zap.c:5403 mkintf: Unable to open channel 1: No such device here = 0, tmp->channel = 1, channel = 1 Apr 29 18:59:25 ERROR[8192]: chan_zap.c:7526

Hi all, I've done this a few times with other PBX's but swyx has stumped me! I'm having some trouble getting Asterisk connected to a Swyx system using a sangoma A104dx... currently the setup is: BT <-> Swyx The above setup works fine... what i'm trying to achieve is BT & SIP Trunks <-> Asterisk <-> Swyx I have connected to our BT (2 x ISDN30 UK) with

Hello all. I have here a TE110P (configured as E1) and a TDM400P (with four X100P - FXS). Both boards are recognized by the operating system as showed above: 0000:08:00.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device b1d9:0003 Flags: bus master, medium devsel, latency 64, IRQ 169 I/O ports at e800 [size=256]

I need your help I have a sangoma A104D on my dell server; I got card status ok with no alarm If I dialed the extension 6210006, it shows the output as stated below, but there is no ringing from the pstn number nor the iax softphone am using on my pc. I will be glad if someone can give me a working config? What I want to achieve is to send all my call to the pstn on A104D? The pstn am

Im trying to install and configure sangoma ... every thing is OK but when type the command "wanrouter start" the following error apears: wan Driver not found. Thanks for any help

Hey all, ? I'm trying to get an E400P and 2 X100Ps working together in the one box and don't seem to be having much luck. ? I can get the two different types of boards working separately, but not together.? I've made calls on both the X100P and have seen sync and correct signalling on the E400P.? But when I try to enable to configs together I get the following: ? modprobe wcfxo

<P>hi Everyone,</P> <P>We are configuring an ISDN PRI E1 with an E100P card, when you load the drivers, and starts the asterisk, cards also starts fine, givin following output,</P> <P>*CLI> <BR>&nbsp; == D-Channel on span 1 up<BR>&nbsp;&nbsp;&nbsp; -- B-channel 1 successfully restarted on span 1<BR>&nbsp;&nbsp;&nbsp; --

I've been beating my head a bit against the 1.0.6 Debian builds of Asterisk, using an E100P (E1, single span) board. In machines I've built in the past (back in 1.0.0 days), config I'm using and that card and 1.0.0 driver combo worked fine. ztcfg reports no problems: SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) 31 channels configured. And zttool sees the card, and

Hi, I am having some problems mentioned below, the box is in production live environment with traffic around 30 - 100 calls. I am running T/E410P in a Dual P4 xeon with HT disabled. I am using zaptel 0.9.0 and asterisk stable 1 release. There is no gui, just mysql, perl (small script) and asterisk. System runs very smoothly if the calls are around 40-50 and comes one by one , however sometimes

Hi all, I've setup a PBX in production environment last week but we have immediatly find out drop conversations and lot of errors (in asterisk logs) like: Apr 10 17:30:48 NOTICE[25154] chan_zap.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 2 My configuration is: Motherboard: SuperMicro P8SCT (Intel E7221 chipset) Hypertrading and APIC enabled CPU: P4 3GHz Digium TE205P

Hello, I have following problem with Sangoma A104 card: CLI> pri show span 1 Primary D-channel: 16 Status: Provisioned, Down, Active Switchtype: EuroISDN Type: CPE Window Length: 0/7 Sentrej: 0 SolicitFbit: 0 Retrans: 0 Busy: 0 Overlap Dial: 0 T200 Timer: 1000 T203 Timer: 10000 T305 Timer: 30000 T308 Timer: 4000 T313 Timer: 4000 N200 Counter: 3 NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI

Hello list , I?m putting to work a new asterisk box. I?m running * 1.0.3 with (one ) Wildcard TDM ( 2FXS* 2FXO) and (one) E-100P. Both boards are working well. ztcfg don?t show me any error. zttool list both cards as "OK" But when i run asterisk on verbose mode i get those errors : [chan_zap.so] => (Zapata Telephony) == Parsing '/etc/asterisk/zapata.conf': Found --

hello all, i'm using TE110P and all configuration prosess is done. but after i do the 'modprobe' for zaptel and wcte11xp, follow by ztcfg -vv and asterisk -vvvgc i have this error. *CLI> May 27 14:44:33 WARNING[3059]: chan_zap.c:8534 pri_dchannel: PRI Error: We think we're the network, but they think they're the network, too. May 27 14:44:34 WARNING[3059]: chan_zap.c:8534

Hi, I'm having trouble configuring and E1 link , I know the E1 is a PRI and the switchtype is 5ess. The problem is that everytime I try to dial I got and error saying that it was unable to open the zap channel . Devices are created in the /dev/zap directory and I can open them with a cat /dev/zap/1. I can also see the channels in /proc/zaptel/1. Thanks in advance [zaptel.conf]

Hi I have recently upgraded my Asterisk system (from 1.2 to 1.4) and I have started to notice the following messages when I recieve a call on my Zap channel :- [Mar 11 09:20:17] WARNING[4294]: chan_zap.c:8851 zt_pri_error: 1 copying 5 bytes LLC I have a single PRI ISDN 30 link to a Siemens Realitis DX. Here is my zapata.conf :- [channels] echocancel=no echocancelwhenbridged=no rxgain=-5.0

Hi, I'm installing E100P for isdn pri line. My configuration are like this. zaptel.conf ======================================= span=1,0,0,ccs,hdb3,crc4 loadzone = us defaultzone=us bchan=1-15 dchan=16 bchan=17-31 zapata.conf ================================================= [channels] context=default switchtype=euroisdn context=default signalling=pri_net usecallerid=yes

I have spent some time this morning trying to add an Astribank to our current Asterisk, but it failed, so I just removed the hardware, restore the config files to the original setup and started asterisk.; I could see that no Zap channels are started so I did load chan_zap.so: pbx*CLI> module load chan_zap.so [Feb 26 10:32:18] WARNING[3809]: pbx.c:2968 ast_register_application: Already have an