similar to: RE: AVM A1 (OLD) CARD

Hi ! I've fetched a spare AVM B1 card from the cellar, and installed it. After "modprobe b1pci" I did "capiinit" and capiinit moaned about a missing t1.b4. So I search the web and found one at http://www.avm.de/ftp/cardware/b1/x_misc/ddi/. When I now look at the controller, I finally see p2p-mode: # cat /proc/capi/controllers/1 name b1pciv4-a400 io

Hi guys, I'trying to setup Asterisk with an AVM Fritz PCI ISDN card with no success. I have an IP phone from Micronet and I want to receive and place calls over ISDN. But I'm not sure if I need the binary CAPI from AVM or isdn4linux. I've tryed with redhat 9 and with Suse 8.2. Cold someone help me? Thank you very much.

Hello, I have been wrestling with installing the CAPI drivers for AVM Fritz in order to use chan_capi with Asterisk. I use an SMP machine, RH 9. I have found rpm's for CAPI and AVM drivers (namely: capi4k-utils-2003.06.16-08.mungo.RH9.i686.rpm and kernel-2.4.20-8- avmfcpci-03.11.02-08.mungo.RH9.i686.rpm), but I believe that they support only single processor machines. I've already

Hi List Is there a cron that I con do to replace this, as the fx0 card doesnt hang up properly phonegc:/home/samantha# asterisk -r Asterisk CVS-05/30/03-17:17:07, Copyright (C) 1999-2001 Linux Support Services, Inc. Written by Mark Spencer <markster@linux-support.net> ========================================================================= Connected to Asterisk CVS-05 currently running on

Hi Has anyone had any luck in putting two of these im a box? May I ask how.... I am starting to go bald.... I do have a suggestion is make another box and link them with iax2 Thanks Samantha r2d2:/home/s/samantha# ztcfg -vv Zaptel Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) 2

Hello, I've been using * for quite a while using AVM C4 card and a few Grandstream Budgetone 102 hard phones plus couple of HandyTone 286. Echo is a big problem. I am getting used to it, but some users complain. Anyone has experience w/ regards to echo comparing the AVM C4 with two HFC-cards? Before shelling out time and money, maybe someone else already has done so, and could tell me if

Hey Guys We are replacing a BM4 with a trixbox (asterisk) virtual numbers as the customer wants to move the callcentre. They are asking for an equiv to the ipview I gather HUD may be or the panel view The problem is that we need to see (a) total calls in the queue (b) calls for specific DID - How can you give 1 DID preference to another DID ie DID 61740410001 = Fred Electrical DID

Hi I have installed 2 fx0 cards into a machine 1 for pstn (out) and the other for pstn (in) However I can get the first card (pstnout to work fine) I have swapped the cards and both work I am also unable to make outgoign on the second card ztcfg -v shows r2d2:/etc/asterisk# ztcfg -v Zaptel Configuration ====================== 2 channels configured. My /etc/zapdata.conf file # fxsks=1,2

Has anyone got the BT Speedway (AVM Fritz) card working on a RedHat 8.0 system with *. If so could someone give me some pointers on getting the right sequence of installing the drivers and which versions to use. Thanks, Stuart -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi * Fans, I have some fritz cards now, followed instructions from stuart hirsts email of Jun 28: -> Thanks for your info but I think I have it working at last. Below are the steps I took which might help others. 1) Download the PCI AVM drivers from ftp://ftp.avm.de/cardware 2) Download the Chan_capi from http://www.junghanns.net/asterisk/ 3) tar -xvzf fcpci-suse8.0-03.09.10.tar.gz which

hello, does anybody know how to setup avm fritz pci card in p2p mode ? regards marian -- SUNTEQ s. r. o. Hviezdoslavova 9 # Prievidza # 971 04 # Slovak republic Tel: +421-46-5430 754 # Fax: +421-46-5439 144 http://www.sunteq.sk/ ------------------------------------------------------------ A mind is like a parachute... it only works when it's open.

hello! I'd like to use my asterisk-box on a p2p-line from my alcatel pbx. isdn4linux and capi works fine on a s0-line from the pbx, but i need more then 8 msns, cause i'd like to implement a voice-mail system and an extension to our "old" pbx with voip-phones. had anyone success using isdn4linux on a t0 (p2p) line (of course with an inexpensive passive card like my avm

Hi, I tested the capi_chan with latest cvs of * and I have problems with Early-B3. The following dialstring works for me (without Early B3): exten => _0X.,1,Dial(CAPI/@22715291:${EXTEN:1}|30) But if I add the 'b' for using Early-B3 exten => _0X.,1,Dial(CAPI/@22715291:b${EXTEN:1}|30) nothing changes (no dialtone). If in this example the called party discards the call, there is no

hi all it seems like whatever I do, I can't use more than 1 BRI on my AVM C2 with chan_capi. Both channels seem to work, but not at the same time. And - yes - they're connected to different NT boxes :) Any ideas? kapejod? -- Roy Sigurd Karlsbakk, Datavaktmester ProntoTV AS - http://www.pronto.tv/ Tel: +47 9801 3356 Computers are like air conditioners. They stop working when you open

Hi, Has anybody used AVM C1/C4s on Asterisk? What's the result? I know there may be better cards, but I have 2 C4s which I want to put to good use. Andrea Coppini +356 79 ANDREA (263732) andreacoppini@iwg.info EMPOWER PEOPLE - THE WORLD IN YOUR HAND iWG (iWORLD GROUP) is a global e-mobile company creating, building and growing new businesses. iWG founders are pioneers in creating

All, I have been trying to get CAPI4Linux working on my machine and being frank am failing miserably! I am looking for any help available, I am real newbie (so please be gentle) and choose to run Mandrake 9.2 as it appears quite friendly (or so I thought!). I have been following the guidance found at http://www.voip-info.org/wiki-Asterisk+How+to+connect+with+CAPI for the AVM card (actually I

Hello! Is there a way to use AVM Fritz!PCI as a ZAP interface and have it configured for ZAP channels? Thanx in advance! Roland Zagler mailto:r.zagler@fog.at @fog smart partners

Hi list, i'm keen to move to Asterisk 1.6, so really need to update my system which is running Mandrake 9.2 although it has been solid for years, fo Fedora 8. I have a Fritz! card for ISDN BRI, I have installed the drivers/kernel drivers from ATrpms (http://dl.atrpms.net/all/fcpci-03.11.07-14.fc8.i386.rpm and http://dl.atrpms.net/all/fcpci-kmdl-2.6.23.14-115.fc8PAE-03.11.07-14.fc8.i686.rpm)

Hello, I?m trying to compile the Fritz CAPI module for Debian stable, following the steps related in http://www.voip-info.org/tiki-index.php?page=Asterisk%20AVM%20Fritz%20CAPI%20Driver%20Install But I always get the same error, debian-asterisk:/home/ismaelg/fritz# make (cd src.drv; make CARD=fcpci) make[1]: Entering directory `/home/ismaelg/fritz/src.drv' cc -c -DMODULE

Running dovecot 1.2.12 on ubuntu 10.10. Here is the problem: I have mysql backend for expire. I am using the dovecot-postfix package which creates /etc/dovecot/conf.d/01-mail-stack-delivery.conf which looks like this: # Some general options protocols = imap imaps managesieve disable_plaintext_auth = no ssl = yes ssl_cert_file = /etc/ssl/certs/ssl-mail.pem ssl_key_file =